Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 1 Vax Careline: 0870 6061248 www.vax.co.uk VO-7000 Wet/Dry vac with exclusive two-tank system Instruction Manual Please read carefully before using the Wet/Dry vac. Always fully extend the mains cable before use.
Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 2 Parts overview 1. Diagram 1 -1 G K I C N M A P B H D L J O E Q R F S Fig.1 Box contents Remove the parts from the tank and check that the following are all present: A. Outer tank B. Inner tank C. Cleaner lid and motor housing D. Caster supports (4) E. Casters (4) F. Caster support screws (4) G. Hose H. Adapter I. J. K. L. Vacuum nozzle Small float ball Wet/dry nozzle Reusable cartridge filter - connected to the cleaner lid M. Crevice tool N.
Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 3 Safety Information 2. Safety Information FOR DOMESTIC USE ONLY When using the Wet/Dry vac, basic safety precautions should always be observed, including the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. The Wet/Dry vac must be stored indoors, in a cool dry area. Turn off the Wet/Dry vac controls before connecting to or disconnecting from the mains supply.
Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 4 Assembly 3. Assembling the Wet/Dry vac Once in place, do not remove the float assembly. NOTE: The large filter cage and the float ball on Wet/Dry vac lid are not removable parts. 1 A B A B 2 3 B A B A Fig.2 Attach caster supports and casters Remove Wet/Dry vac lid and inner tank. Turn outer tank upside down. Match letters (A or B) on bottom of caster support with letters on wet/dry vac tank. Align square tabs (1) on supports with rails (2) on tank.
Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 5 Assembly I Fig.6 Fig.8 Attach hose, wands and cleaning tool Attach drain cap Push hose into hose inlet on tank; twist hose to tighten or loosen connection. The wands and tools attach to hose in the same manner. Screw drain cap (I) on to lower, front of tank as shown. Additional tools and accessories that are not included, are available at additional cost from your Vax Service Cente or Authorised Vax Dealer. Fig.
Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 6 Use & Function 4. Using the Wet/Dry vac Cleaner Description 15 16 18 The assembled Wet/Dry vac will look like the drawing (21/2 inch diameter tools are shown on cleaner). 17 Operate cleaner only at voltage specified on rating label on Wet/Dry vac lid. 1 2 3 6 13 5 3 4 1. On/off switch 2. Cleaner lid 3. Cleaner lid latches 4. Carrying handles 5. Hose 6. Hose inlet 7. Wet/dry selector 7 8. Caster supports 12 9. Casters 10. Tank drain cap 11 8 11.
Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 7 Use & Function Dry pick-up Disconnect Wet/Dry vac from electrical outlet. With hose removed from cleaner, slide wet/dry selector (A) to expose ‘dry tank inlet’ (B). (Fig.11) Selector will snap into place. Insert hose into ‘dry tank inlet’. Attach the desired tool to hose end. Make sure cleaner lid is locked in place. A Fig.
Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 8 Use & Function Single tank operation Dry tank dust For picking up very large amounts of debris (either wet or dry), the cleaner may also be operated without the inner tank in place. Disconnect Wet/Dry vac from electrical outlet. Remove inner tank and set aside. Attach hose to either the wet or dry intake port. Plug power cord into a properly grounded outlet and turn cleaner on. When using single tank for dry pick-up, cartridge filter must be in place.
Vax VO-7000 D7 IL 10/19/04 3:35 PM Page 9 Use & Function/Maintenance Note: If not very full, the inner tank may be easier to empty if it is removed from the outer tank. When emptying the inner tank, do not grab on to filter cage. Fig.15 Storage Empty tanks (see ‘Maintenance’ section). Rinse inside of tank thoroughly with clean water particularly if spills or other liquid substances other than plain water have been picked up. Wipe inside of tank dry.
Vax VO-7000 D7 IL 10/19/04 3:36 PM Page 10 Maintenance After wet pick-up, allow filter to dry and gently brush with a soft brush. Check filter thoroughly and replace it if there are any tears or holes in it. B If extremely dirty, the cartridge filter can be cleaned by a soft bristle brush. NOTE: Vigorous scrubbing may shorten the life of the cartridge filter. Do not use water to clean cartridge filter.
Vax VO-7000 D7 IL 10/19/04 3:36 PM Page 11 Troubleshooting/Technical Specification 6. Troubleshooting If a minor problem occurs, it can usually be solved quite easily by using the checklist below. PROBLEM: Wet/Dry vac won’t run Cause: Not firmly plugged in Solution: Plug unit in firmly. Cause: No voltage in wall plug Solution: Check fuse or circuit breaker. Cause: Blown fuse/tripped circuit breaker Solution: Replace fuse/reset circuit breaker.
Vax VO-7000 D7 IL 10/19/04 3:36 PM Page 12 EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the product VO-7000 Wet/Dry vac is manufactured in compliance with the following: Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC EMC: 89/336/EEC Electromagnetic Compatibility Directive, as modified by 93/68/EEC Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
