Vax V-008SC User Guide.qxd 6/3/07 14:13 Page 1 Vax careline 0870 6061248 Vax model number: V-008SC www.vax.co.uk instruction manual Bagless upright Please read carefully before using this cleaner. Always fully extend the mains cable before use. Retain for future reference.
Vax V-008SC User Guide.qxd 6/3/07 14:13 Page 2 www.vax.co.uk 1. Diagram V-008SC 1 13 2 3 14 4 15 5 6 16 10 7 17 8 18 9 19 11 20 21 12 21 Fig.
Vax V-008SC User Guide.qxd 6/3/07 14:13 Page 3 Vax Careline 0870 606 1248 2. Safety Information 15. Do not vacuum up hard or sharp objects such as glass, nails, screws, coins, etc. FOR HOUSEHOLD USE ONLY. 16. Do not use without the filters in place. When using the vacuum cleaner, basic safety precautions should always be observed, including the following: 1. Only use the vacuum cleaner indoors on dry surfaces. 2.
Vax V-008SC User Guide.qxd 6/3/07 14:13 Page 4 www.vax.co.uk 3. How to Assemble Re-attach dirt container by aligning bottom of dirt container to bottom of cleaner and push forward to snap into place. Handle Assembly: Tool required: Phillips screwdriver Detach dirt container from back panel of cleaner by pressing dirt container release button and tilting forward. Fig.3/4 Secure Back Hose: Fig.3/1 Wrap hose around back of hose caddy. Push hose wand down into the right side of cleaner (Fig.3/5).
Vax V-008SC User Guide.qxd 6/3/07 14:13 Page 5 Vax Careline 0870 606 1248 4. How to Operate Cord Release: Turn Quick Cord Release for easy cord removal. Store cord in cord grip (see page 2 - parts overview) to keep out of the way while vacuuming (Fig.4/1). Fig.4/3 Handle Release Pedal: Fig.4/1 To release handle, push the handle release pedal located on the lower left side of the cleaner (Fig.4/4). Turn the carpet height adjuster to match the surface being cleaned (Fig.4/2).
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 6 www.vax.co.uk NOTE: Rotating brush could cause area rug fringe to become tangled within cleaner. Use caution when vacuuming throw rugs with fringe.. ! Above Floor Cleaning: Extension Tube: If additional length is needed, use the extension tube and crevice tool. Pull crevice tool out of extension tube. Use extension tube and crevice tool together or separately. Cleaner must be in its upright position to raise brushbar. Fig.4/9 Fig.
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 7 Vax Careline 0870 606 1248 5. Dirt Container & Filters: Removal and Replacement ! WARNING: To reduce the risk of injury from moving parts, unplug before servicing. Emptying the dirt container: Press dirt container release button and remove dirt container from cleaner (Fig.5/1). Fig.5/3 Lift filter cartridge out of base of cleaner (Fig.5/4). Fig.5/1 Hold dirt container over dustbin and press clean release dirt container button to empty.
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 8 www.vax.co.uk Replace filter cartridge: Return filter cartridge to base of cleaner (Fig.5/9). Fig.5/6 Wash foam filter: Hold foam filter under running water to wash (Fig.5/7). Ring excess water out of filter. Allow filter to dry for at least 24 hours before replacing in filter cartridge. Fig.5/9 Click buttons back into place to lock filter cartridge in base of cleaner (Fig.5/10). Fig.5/7 Fig.
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 9 Vax Careline 0870 606 1248 Pull out and wipe with a damp cloth to clean (Fig.5/12). Regular Maintenance Each time the dirt container is emptied, the filter should be cleaned. Tap the filter firmly against the inside of a dustbin until the dirt stops falling from the filter. The filter will be discoloured after use, but this will not affect the filter’s performance. Do not brush the filter.
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 10 www.vax.co.uk Place new belt in area of brushbar without bristles (Fig.6/5). Fig.6/2 Lift and remove brushbar (Fig.6/3). Dispose of old belt. Fig.6/5 With new belt in place, pull and slide brushbar into nozzle making sure that the brushbar end caps are in the correct orientation (inset). Rotate brushbar manually to make sure belt is properly aligned (Fig.6/6). Fig.6/3 To replace belt or brushbar: Slide belt onto motor shaft (see Fig.6/4).
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 11 Vax Careline 0870 606 1248 Secure by aligning the three (3) tabs in the base slots. 7. General Maintenance ! SLOTS WARNING: To reduce the risk of injury from moving parts, unplug before servicing. Debris removal - hose: Check to see if dirt container is full; empty if needed TABS Fig.6/8 Replace all three (3) screws to secure nozzle guard (see Fig.6/9). Fig.6/9 Plug cleaner in and check to see if there is any suction at end of hose.
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 12 www.vax.co.uk 8. Troubleshooting Debris removal - TurboTool: Rotate locking ring 180° and turn TurboTool over (Fig.7/3). WARNING: To reduce the risk of personal injury, unplug the vacuum cleaner before performing maintenance or troubleshooting checks. ! LOCKING RING Fig.7/3 Pivot lower housing and remove clog (Fig.7/4). Fig.7/4 To reassemble, be sure tabs are engaged. Pivot the lower housing closed (Fig.7/5). Fig.
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 13 Vax Careline 0870 606 1248 9. Technical Specification Voltage: Wattage: Capacity: Filters: Cord length: Weight: 220-240V ~50Hz 1550W 2.2L Foam and pleated HEPA pre motor filters 9.2m 9.35kg Subject to technical change without notice.
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 14 www.vax.co.
Vax V-008SC User Guide.
Vax V-008SC User Guide.qxd 6/3/07 14:14 Page 16 EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the V-008SC Performance Cyclonic Upright is manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage Directive EMC: 89/336/EEC Electromagnetic Compatibility Directive Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
