User`s guide
5-1
5-2
A-I
A-2
Example No.
2-1
2-2
4-1
4-2
4-3
4-4
4-5
5-1
5-2
5-3
6-1
6-2
6-3
6-4
7-1
7-2
7-3
7-4
7-5
7-6
7-7
7-8
7-9
7-10
Diagnostic Programs
on
TU58 #39 ..........................................................................
5-5
Diagnostic Programs
on
TU58 #44 .......................................................................... 5-5
Internal Processor Registers ..................................................................................... A-I
Machine-Dependent Internal Registers .................................................................... A-2
EXAMPLES
Title
Page
Printout Produced by the Console Terminal as the
CPU
Enters
the Console
I/O
Mode.. ................... ........ .... ... ....... ...................... ....... ............ .......... 2-7
Evoking the
Customer
Runnable Diagnostic
Auto
Mode
Package-
File
Not
Found
....................................................................................................... 2-18
Console
Printout
at
Power-Up
as
the
CPU
Enters
MICMON
................................ 4-3
Console
Printout at Power-Up
as
the
CPU
Enters the Console
I/O
Mode.......................... ........
...
..... ............................ ....... ................ ...................... 4-4
Console Printout of the
CPU
Entering the
MICMON
from the Console
I/O
Mode....... ....... ........ .... ................... ................ .........
...
.... ....
...
.... ........................
...
4-4
MICMON Error Printout ......................................................................................... 4-5
MICMON
Error Printout After
SE
TR
Command ................................................. 4-5
Console Printout of Booting the Diagnostic Supervisor from the
RL02 Diagnostic Distribution Disk ........................................................................... 5-2
Console Printout of Booting the Diagnostic Supervisor from the
R80 System Disk .......................................................................................................
5-3
Typical Autosizer Printout of a
RL02/R80
Configured VAX-I
1/730
System ...... 5-9
HALT
in
Hardcore Instruction Test .........................................................................
6-3
Level 4 Diagnostic Program Set Up to Loop on Hard Error.................................. 6-4
Level 4 Program Listing Sample EVKAA, Test 12, Subtest
55
............................. 6-4
Setting
Up a Loop on an Intermittent Error ............................................................ 6-4
Printout of an
AUTO
Mode Testing Sequence on a RL02/R80-Configured
System
in
Which the System Was Improperly Set Up ............................................
7-3
Printout of an
AUTO
Mode Testing Sequence
in
Which No Errors
Were Encountered .....................................................................................................
7-5
Printout of an
AUTO
Mode Testing Sequence in Which
DQAO
Was
WRITE-PROTECTed ............................................................................................... 7-6
Printout of an
AUTO
Mode Testing Sequence
in
Which
DQAO
Was Off-Line ....
7-7
Printout of an
AUTO
Mode Testing Sequence
in
Which a
Microdiagnostic
Program File Was Missing.............................................................
7-7
Printout of an
AUTO
Mode Testing Sequence in Which an Error
Was Detected During Microdiagnostic Testing ........................................................
7-8
Printout of an
AUTO
Mode Testing Sequence on a RL02/R80-Configured
System
in
Which an Error Was Detected During Macrodiagnostic Testing ........... 7-9
Printout of the
MENU
Mode Main Menu .............................................................
7-11
Printout of the
MENU
Mode
in
Which Choice A Was Selected from
the Main Menu ........................................................................................................ 7-12
Pdntout
of the
MENU
Mode
in
Which Choice B Was Selected from
the Main Menu ........................................................................................................ 7-12
VI