Technical information

0115 900 5858
20
®
20
I
N
L
I
N
E
C
O
M
P
O
N
E
N
T
S
www.diversitech-uk.com
VCRT-1 Core Removal Tool EA 1
LINE PIERCING VALVES AN D TOOLS
Core Removal Tool
Designed to remove and replace valve cores
without losing the refrigerant charge. Connects
to any 1/4” male flare fitting. Saves time, saves
refrigerant.
VCRT-1
CATALOGUE NO. DESCRIPTION ORDER UOM ORDER MULTIPLE
Features a valve core in the 1/4” male port.
Simply pierce the line and back seat the needle.
Flow starts when depressor type charging hose is
connected. Flow shuts off automatically when hose
is removed. If valve core is not desired, it may be
removed. Connect hose, pierce line and back seat
needle. This method offers full unrestricted flow.
Valve core can be removed or changed at any time
without loss of refrigerant if needle is front seated.
QT-1 Quick-Tap – 6.4mm, 8mm, 9.5mm O.D. Tube Size EA 1
QT-2
Quick-Tap – 13mm, 16mm O.D. Tube Size EA 1
Quick-Tap
QT-1
Quick-Tap-2
QTH-1 Quick-Tap-2 – 6.4mm, 8mm, 9.5mm O.D. Tube Size EA 1
QTH-2
Quick-Tap-2 – 13mm, 16mm O.D. Tube Size EA 1
Identical to Quick-Tap except that a nylon handle
replaces the hex wrench. Phillips-head screws
are used.
QTH-1
MAC- The Ultimate in Line
Piercing Valves
Install valve. Connect charging hose. Service. That’s
all there is to it! MAC features Uniport: 1 connection
for piercing and servicing. Sealed with refrigerant
resistant “O” rings. Needle automatically back
seats after servicing, leaving line free of restriction.
Connect to tubing with 2 socket-head screws.
(Hex wrench is included with each valve.) Needle
depressor is inserted into head of needle. Wing
cap is turned down easily by hand until line is
pierced. Wing cap is removed and system may
be serviced with any charging hose with built-in
depressor. When hose is removed, spring loaded
needle back-seats forming a leak proof seal. Needle
depressor is discarded and wing cap forms extra
precautionary seal.
QTM-1
QTM-1 MAC Line Piercing Valve – 6.35mm, EA 36
8mm, and 9.5mm O.D. Tube Size
QTM-2 MAC Line Piercing Valve – 13mm, EA 36
16mm O.D. Tube Size
QTM-3 MAC Line Piercing Valve – 4.75mm, EA 1
6.4 O.D. Tube Size
CATALOGUE NO. DESCRIPTION ORDER UOM ORDER MULTIPLE
QT-100 Quick-Tap-2 – 6.35mm, 8mm, EA 1
and 9.5mm O.D. Tube Size
QT-100N
Replaceable Hardened Steel Needle and Gasket EA 1
QT-100G Replacement Gasket Only EA 3
Insta-Tap Refrigerant
Recovery Tool
The fastest, easiest way to evacuate refrigerant
before disposal of a unit. Snaps onto refrigerant line
for full and immediate flow. Punctures super large
hole for maximum full flow discharge to recovery
unit. One tool fits all sizes from 4.76mm to 22.2mm
O.D. hard tubing. Replaceable needle.
CATALOGUE NO. DESCRIPTION ORDER UOM ORDER MULTIPLE
QT-100
Line Tap and Swivel Valves
The quick, safe and easy option to charge, discharge
and test a line. Simply clamp on the DLT valve, attach
the DCV-1G control valve, and pierce the line. The
control valve features a port for connecting charging
lines or gauges. The valve can swivel to any position
and also be removed and re-used. These line tap
valves are also difficult to tamper with as the line
can only be accessed by using the special DCV-1G
valve. They feature a specially formulated gasket
which can withstand heat up to 150°C. Available in
four sizes from 4.8mm O.D. tube size to 9.5mm.
The DCV-1G is designed for use with all four sizes.
DLT series line taps are also compatible with existing
A-1 Components CV-1G valves and likewise DCV-
1G valves are compatible with A-1 Components
LT-series line taps.
DLT-3G Line Tap Valve – 4.75mm O.D. tube EA 1
DLT-4G Line Tap Valve – 6.35mm O.D. tube EA 1
DLT-5G Line Tap Valve – 8mm O.D. tube EA 1
DLT-6G Line Tap Valve – 9.5mm O.D. tube EA 1
DCV-1G Valve for DLT Line Taps EA 1
DLT-4G
CATALOGUE NO. DESCRIPTION ORDER UOM ORDER MULTIPLE
CATALOGUE NO. DESCRIPTION ORDER UOM ORDER MULTIPLE
Core Storer
All steel valve core remover and storage container.
Completely knurled for easier grip, eliminating
slippage when using with oily or greasy hands. Core
Storer features a compartment for storing extra valve
cores. Four replacement cores are included with
each tool.
VCR-1
CATALOGUE NO. DESCRIPTION ORDER UOM ORDER MULTIPLE
VCR-1 Core Remover and Storer EA 1
CATALOGUE NO. DESCRIPTION ORDER UOM ORDER MULTIPLE