VAUXHALL Combo Owner’s Manual Model Year 2010 Edition: June 2009 TS 1649-A-10 Operation, Safety, Maintenance
Data specific to your vehic le Please enter y our vehicle’s data here to keep it easily accessible. This data can be found und er the sections "Technical da ta" and "S ervice and m aintenance" as well as on the identification plate.
Introduc tion Make use of the Owner’s Manu al Your vehicle is an intelligent sy nthesis of adv anc ed technology , proven safety, env ironmenta l friendliness a nd economy. z The "In brief" section will give you an initial overv iew. It now lies with you to drive your vehicle safely and ensure that it perform s perfectly. This O wner’s Manual provides you with all the necessary information to that end.
Contents Comm itment to custom er satisfaction: Our ai m: to k eep you happy with your vehicle. All Vauxhall Authorised Repairers offer first-class serv ice a t competitiv e prices. Experienced, factory-trained technicians w ork according to factory instructions. Y our Authorised Repa irer can supply you with GEN UINE VAU XHALLAPPRO VED PARTS , which hav e und ergone stringent quality and precision chec ks, and of course useful and a ttrac tiv e VAUXHALL-APPROVED AC CESSO RIES.
2 In Brief In Brief Unlocking the vehicle: Turn the key in the lo ck fo rwards or press the q button on the radio remote control 3 Unlo cking the tailgate 3: Turn the key to the horizontal po sitio n or press the q bu tton on the rem ote con trol 3 Pull on the door ha ndle and open the d oor or slide open the slid ing door 3. Press the button to open the tailgate. Sliding door 3 3 25.
In Brief Unloc king the rear doors 3: Turn the key to th e vertical position or press the q button on the remote control 3 To open the right rear door, pull on the handle and p ull open the door. To open the left rear door, turn the handle on the inside. When using the rem ote control, the rear doors are only unlocked if the key slot in the lock is in the vertical p osition. If the key slot is in the horizontal position, the rear doors are a lways locked.
4 In Brief Fro nt seat height 3 : Pull lever at side To fold fro nt seat backrest forward 3 : Raise release lever Lift lever a nd relieve som e weight from seat to raise it or press down on seat with body weight to low er it. Sea ts 3 36, Seat position 3 37. Never adjust the driver’s seat whilst driving. It could m ov e in a n uncontrolled m anner when the lev er has been pulled . Seats 3 36, S eat p osition 3 37.
In Brief 5 Pull out the seat belt and engage it in the belt buckle Adjust the exterior mirror manually using the handle Electrical exterior mirror adjustmen t 3 The seat belt must not b e twisted and m ust lie snugly a gainst the body. The back rest must not be tilted back too far (maxim um approx. 25°). Mirrors 3 32, Aspherica l ex terior mirrors 3 32, Folding the exterior m irrors 3 32. S elec t the corresponding ex terior mirror with the rock er switch and ad just with the four-way switch.
6 In Brief To adjust interior mirror by swivelling Swiv el lev er on underside of mirror housing to red uce daz zle a t nig ht. Mirrors 3 33. Steering wheel adju stment 3: Swivel lever down, adjust height, swivel lever up, engage Ad just steering wheel only when vehicle is stationary and steering column lock is relea sed. Airba g systems 3 3 54.
In Brief Headlight flash, m ain beam and dipped beam Headlight flash = Main beam Dipped beam = = Pull stalk toward s steering wheel Push sta lk forwards Push sta lk forwards again Main beam, headlight flash 3 81. Switch turn signal on Hazard warning lights Right Left O perated with the ¨ button. = = S talk upwards S talk downwards Turn signals 3 81. Haz ard warning flashers 3 82.
8 In Brief
In Brief 1 Page Side air v ents ... ..... .... ..... .... .... ..... .. 3 89 2 Front pa ssenger airbag 3 .... ..... .. 3 54 3 Infotainm ent system 3 . .... .... ..... .. 3 86 4 Haza rd warning lights .. .... .... ..... .... 3 7 LED for Vauxhall alarm sy stem 3 .... .... ..... .... .... ..... ... 3 30 5 Display 3 for tim e, date, outside tem perature, infotainment sy stem 3 . .... .... ..... .. 3 73 9 Pa ge Windscreen wiper, wind screen wash system, rear window w ash system 3 .... ....
10 In Brief Control indicato rs > Front fog lights 3, 3 63, 3 82. A Engine elec tronics, I mmob iliser 3, Easytr oni c3, Fault , 3 19, 3 63, 3 109. Z Exha ust gases 3 , 3 64, 3 109. v A irbag system s 3, Belt tensioners, 3 64, 3 48, 3 57. I Eng ine oi l pressure, 3 64. p Alternator, 3 66. O Turn signal l ights, 3 65, 3 81. R C Mai n bea m, 3 65, 3 81. Brake system, clutch system 3, 3 66, 3 168. u ! Preheat ing 3, diesel p articl e filt er 3, 3 65, 3 110.
In Brief Operate horn: Press j right or left Airbag system 3 3 54, Rem ote control on steering wheel 3 3 86. Windscreen wiper: Move stalk upwards & % $ § = = = = Fast Slow Ad justable interval switching Off Windscreen wiper 3 78, Adjusta ble wip er interval 3 3 79, Further informa tion 3 154, 3 168. Operating windscreen wash system: Stalk to ward steerin g wheel Windscreen w ash system 3 78, Further inform ation 3 169, 3 182.
12 In Brief Rear win dow wiper 3 and Rear win dow wash system operation Wiper on = Wiper off = Washing = 3 Push sta lk forwards Stalk toward steering wheel Push sta lk forward and hold Rear window wiper and rear wind ow wash system 3 78, Further information 3 168, 3 169. Heated rear window 3 , heated exterior mirrors 3 Operated with the Ü button. Climate control system 3 88, H eated rea r wind ow 3 35. To clear fogged or icy windo ws Turn the rotary k nobs for temperature and air flow clockwise.
In Brief 13 Before starting off, check z Tyre pressure and tyre condition 3 114, 3 179, z Engine oil level a nd fluid levels in engine compartment 3 163 to 3 169, z All windows, mirrors, exterior lig hting and number plates are free from dirt, snow and ice a nd operational, z Seats, seat belts and mirrors are correctly a djusted 3 36, 3 46, 3 32, z Check brake func tion at low speed , particula rly if the b ra kes are wet.
14 In Brief Steering c olum n lock and ignition Starting the engine Turn key to position 1. Mov e the steering wheel slightly to release the steering column lock. Depress the c lutch and brake ped als, Easytronic 3 in N , do not acc elerate; for diesel engine, turn key to p osition 2; when control indicator ! goes out turn the key to position 3 and release it w hen the engine is running.
In Brief Parking the vehicle z Alwa ys apply ha ndb rake firmly without op erating the release button, and apply as firmly as possible on a downhill or uphill slope. z Switch off the eng ine and ignition by turning the ignition key to 0 and removing it. Turn the steering wheel until you can feel its loc k enga ge (anti-theft protection). On vehicles with Ea sytronic 3 , control indica tor R flashes for a few seconds after the ig nition is switched off if the handb ra ke has not been app lied.
16 In Brief Airbag system The a irb ag system c onsists of several internal systems. Front airb ag system 3 The front airbag system will be triggered in the event of a serious ac cident involving a frontal impact and forms safety cushions for the driver and front passenger. The forward movement of the driver and front passenger is checked and the risk of injuries to the upper body a nd head thereby substantially reduced.
In Brief 17 Diesel partic le filter 3 The diesel particle filter sy stem filters ha rm ful soot particles out of the exhaust gases. The system includes a self-cleaning function that run automa tic ally during driving. The filter is cleaned by burning off the soot pa rticles at high tem perature. This proc ess ta kes place automatically under set driving conditions and may ta ke up to 25 minutes. Fuel c onsumption may be higher during this period.
18 Keys, doors, windows Keys, doors, windows Replacement keys The key number is specified in the Car Pass 3. The key is part of the electronic immobiliser. Locks 3 20, 3 155. Replacem ent keys ... ..... .... ..... .... .... ..... . Key with retractable key blade 3 ..... . Ca r Pass... .... .... ..... .... ..... .... ..... .... .... ..... . Electronic immobiliser... .... ..... .... .... ..... . Mechanica l unlocking or lock ing of ind iv idual doors. .... ..... .... ..... .... .... ..... .
Keys, do ors, windo ws 19 If control indica tor A illuminates a fter the eng ine has started, there is a fault in the eng ine electronic s or Easytronic transmission 3 100. Not e The immobiliser does not lock the doors. Y ou should always lock the vehicle after leaving it and switch on the Vauxhall alarm system 3, 3 20, 3 22, 3 29. Electronic immo biliser The system check s w hether the vehicle is allowed to sta rt with the key used.
20 Keys, doors, windows Mechanical unlocking or lo cking of individual doors (versions without rem ote control 3 and central lock ing sy stem 3) Front doors and sli ding doors 3 To unlock Turn k ey in lock towards front of vehicle as far as it will go. Return key to the vertical position and remove. Pull door handle. To lock With door or sliding door closed, turn key towards rear of vehicle as far as it will go. Turn key back to vertical position and rem ov e.
Keys, do ors, windo ws 21 Fault If the central locking system cannot be operated with the remote control, it m ay be due to the following: z Range exceed ed. z Battery voltage of the radio remote control too low, cha nge battery. z Frequent, repeated operation of the remote control outside the reception rang e of the vehicle (e. g. too far from vehicle, rem ote control is then no longer recognised). S ynchronise the rem ote control. The rem ote control is integ ra ted in the key .
22 Keys, doors, windows Key with fixed key sec tion Have the ba ttery changed in a work shop. Radio rem ot e c ontrol synchronisat ion After changing the ba ttery, unlock the door with the key in the lock 3 24. Inserting the key in the ignition synchronises the remote control. Remote contr ol batt ery replac em ent Replace the battery as soon a s the range of the remote control begins to shrink . Batteries do not belong in household waste.
Keys, do ors, windo ws 23 Not e z To prevent the driv er from being ina dvertently locked out, the b utton on the driver’s door cannot be depressed when the door is open. z If the driv er’s door is not closed properly , the central loc king sy stem will unlock again immediately after lock ing. z A short time after unlocking with the remote control, the doors loc k again autom atically if no door is opened. z To loc k the d oors from insid e (e.g.
24 Keys, doors, windows Fault If the central locking system cannot be opera ted, the problem may be as follows: Malfunction in central lockin g system To unlock Turn the key in the driver’s door lock towards the front of vehic le, turn it b ack to the vertical position and rem ove. The driver’s door is unlocked. The other doors can b e opened b y pulling the lock button (unless the anti-theft locking system 3 is active). The load compartm ent and tank flap remain locked.
Keys, do ors, windo ws Sliding doo rs 3 9 Warning If the vehicle is parked facing down a slop e, open slid ing doors m ay mov e accidentally on account of their weight. Close the slid ing doors before driving off. O peni ng from outside Unlock the door with the key b y turning it forwards in the lock or p ressing the q button on the rem ote control. To open the slid ing doors, pull the handle and slide the door towards the rear of the vehic le.
26 Keys, doors, windows Tailgate 3 To open Turn the key in the lock to the vertical position or press the q b utton on the rem ote control. Press the button to open the tailgate. To close Close the tailgate and turn the key in the lock to a horizontal position or p ress the p button on the rem ote control. Central l oc king 3 and the ta ilgat e The central lock ing sy stem and a nti-theft lock ing sy stem 3 for the doors cannot b e op erated via the tailgate lock.
Keys, do ors, windo ws Rear do ors 3 To open Turn the key in the lock to the vertical position or press the q b utton on the rem ote control. O pen right-hand rear door from outside b y raising door ha nd le or from insid e b y pivoting handle. Unlock and open the left-hand rear door from inside by pivoting the handle. The doors engage at a 90° p osition.
28 Keys, doors, windows Notes on tailgate or rear doo rs z After fitting certain accessories, it m ight not be p ossible to k eep the tailga te in the open position. z The number p la te can only be seen when the tailgate or rear doors are closed. Do not driv e w ith a n op en tailgate or open rear doors. 9 Warning Do not drive with load c om partment open when transp orting bulky objects, for example, since toxic ex haust fumes could penetrate the interior.
Keys, do ors, windo ws Vauxhall alarm system 29 3 monitors z the doors, load compa rtm ent, bonnet, z the passenger c om partment, z vehicle tilt, e. g. if it is raised, z the ignition. 9 Warning Do not activate the system if there are people in the vehicle! The doors ca nnot be unlock ed from inside. To activ ate All doors, windows a nd the bonnet must be closed. Press the p button on the remote control again within 10 seconds of locking.
30 Keys, doors, windows After the first 10 second s of Vauxhall alarm sy stem activation: z LED flashes slow ly z LED illuminates for approx. 1 second = S ystem switched on, = S witch-off function. Contact a workshop for assistance if prob lems are encountered. Light emit ting d iode (LED) During the first 10 seconds of Vaux hall alarm system activation: z LED comes on = Test, dela yed switch-on, z LED flashes ra pidly = Door, load com partment or bonnet open or system fault.
Keys, do ors, windo ws 31 Not e z Modific ations to the passenger compartment, such as fitting seat covers, could hinder the function of passeng er comp artm ent monitoring. z Switch off passenger com partment monitoring of the interior of the parked vehicle is being heated. Ala rm When triggered, the alarm gives off an acoustic sig nal (horn) and a visual signal (hazard w arning flashers). The number and d uration of the alarms are stipulated by legislation.
32 Keys, doors, windows Exterio r mirrors Adjust m anually using handles in the front doors or electrically 3 using switches in the driver’s door console. Manual exterior m irror adj ust ment Adjust the exterior mirror using the handle. Electri cal ext eri or mirror adjustment 3 Select the corresp onding exterior m irror with the rocker switch a nd adjust w ith the four-way switch. To retrac t exterior m irrors The exterior mirrors can b e folded in by pressing gently on the outer edge of the housing.
Keys, do ors, windo ws Heated exter ior mirror s 3 Heating is activated or dea ctivated by pressing the Ü b utton. Heating is op erable when the ignition is switched on. In terior mirror 33 Swivel mirror housing to adjust. Man ual window operation, front doors To reduce dazzle, swivel the lever on the underside of the mirror housing. The door wind ow s c an be op erated using window w inders.
34 Keys, doors, windows Electric win dows 3 9 Warning Exercise care when operating electric wind ow s. Risk of injury, espec ia lly for children. Keep a close watch on the windows when closing them. Ensure tha t nothing becomes trapped in them as they m ov e. Operat ional readiness Operational when the ig nition key is in position 1 in the starter switch. Window in the sliding doors 3 z To op en = Release joint and push outwa rds. z To close = Pull joint and engage.
Keys, do ors, windo ws 35 Fault If the windows cannot be opened and closed automatically, activate the window electronics as follows: 1. C lose doors. 2. Sw itch on ignition. 3. C lose the window com pletely and hold the rock er switch depressed for at least another 5 seconds. 4. O pen the window completely and hold the rock er switch depressed for at least another 1 second. 5. Repeat for each window.
36 Seats, Interior Seats, Interior Front sea ts .. .... ..... .... ..... .... ..... .... .... ..... . Head restraints .... .... ..... .... ..... .... .... ..... . Loa d compartment ex tension .. .... ..... . Lashing eyes 3 .... .... ..... .... ..... .... .... ..... . Loa d compartment cover 3 . .... .... ..... . Safety net 3 .... ..... .... ..... .... ..... .... .... ..... . Loa d compartment grille 3 .. .... .... ..... . Notes on loading the vehic le .... .... ..... . Three-stage safety sy stem.... ....
Seats, Interior Adj ust heig ht of seat Lift lever a nd relieve som e weight from seat to raise it or press down on seat with body weight to low er it. Ti lting t he b ackrests forwa rd In order to fold the backrest forwards, lift the release lever. 37 Seat position 9 Warning O nly drive with the seat correctly adjusted. z Sit with your buttocks as far back against the back rest as possible.
38 Seats, Interior z Sit with your shoulders a s far b ack against the b ackrest as possible. Set the backrest rake so that you can easily reach the steering wheel with y our arm s slightly bent. Maintain contact between your shoulders and the backrest w hen turning the steering w heel. Do not angle the back rest too fa r back. We recommend a m aximum ra ke of approx. 25°. z Ad just the steering wheel 3 6.
Seats, Interior 39 Adj usti ng the cent re rear head restraint 3 To improve visibility when the centre rea r seat is not occ upied or to fold the bac krest, press the d etent springs on the guide sleeves to release the head restra int and push it all the wa y down. Hea d rest raint p osi tion Only d riv e with the head restraint set to the proper position. The rear, centre head restraint 3 ca nnot be removed .
40 Seats, Interior Load c ompartm ent extension Remove the load c om partment cov er 3 if necessary 3 42. Pull out the push-in collars 3 for the IS OFIX child-restraint sy stem mounting . Closely follow the installation instructions accomp any ing the IS OFIX child restraint system. Fold ing down t he rear seat back rests Push the rear, outer hea d restra int 3 down completely or remov e it 3 38. Push the rea r, centre head restraint 3 down completely 3 39.
Seats, Interior 41 Rep osi tioning the rear seats Pull the seat belt slightly forward so that it does not get damaged and aud ib ly engage the b ackrests. Reposition the seat cushions. Insert outer rear head restraints 3. Pict ure no: 12438s.t if To fold one or b oth of the rear seat back rests, press the button at the top to release the backrest (3 40, Fig . 18099 S) and fold it forward. Folding d own the front pa ssenger sea t 3 Push the passenger sea t head restraint down or remove it 3 38.
42 Seats, Interior Lashing eyes 3 Load compartment cover The four lashing eyes in the load compartment that are shown in Fig. 18101 S a re used to secure ob jects that are being transported so that they do not slid e around. To close Pull cov er towards rea r of vehicle using ha ndle and hook into side retainers. The b ra ckets on the floor between the front seats are only used to secure the safety net 3 3 43. They must not be used as lashing eyes.
Seats, Interior Safety net 3 Passeng ers m ust not be carried behind the safety net. The safety net ca n be fitted behind the rear seats or, with the rear seat backrest folded down, b ehind the front seats. Remove the load c om partment cov er as necessary 3 42. Unroll the safety net. Fitting behi nd the rear sea ts There are two installation apertures in the roof fram e ab ov e the rear seats: O pen the cover.
44 Seats, Interior Load c ompartm ent grille 3 To prevent vehicle occupa nts from being injured by loose cargo, a load compartment grille can be insta lled behind the front seats. Sp lit load comp artment g rille 3 To enlarge the load compartment, the grille can be moved forwards on the front passenger’s side. Push the head restraint of the front passenger seat down as far as it will g o 3 38. Tilt front p assenger’s seat bac krest forward by raising release lever and p ush down to lock in position.
Seats, Interior z If the seat b ackrests are not folded down when transporting objects in the load compa rtm ent, the backrests must be fully upright and engaged in position 3 40. z The EC kerbweight includes allow ances for the driver (68 kg), load (7 kg) a nd all fluids (tank 90% full). z Do not a llow the load to protrude ab ov e the upp er edge of the back rests. z Weights and payload 3 177. z The warning triangle 3 a nd first-aid k it (cushion) 3 m ust alway s be freely accessible.
46 Seats, Interior Three-stage safety system Com prising: z three-point seat belts, z belt tensioners at the front seats, z airb ag systems for driver and front passenger 3. The three stages are activated in sequence depending on the sev erity of the accident: z The automatic seat belt locking d evices prevent the belt strap from b eing pulled out and thus ensure that the vehicle occ upa nts are retained in their seats. z The seat belts of the front seats are pulled downwards at the belt buckles.
Seats, Interior 9 Warning Fasten your seat belt before ea ch trip . In the event of an a ccident, persons not wearing sea t belts end ang er their fellow occupants and themselv es. Seat belts are only designed for use by one person at a tim e. They are not suitable for persons young er than 12 years of age or smaller than 150 cm. For children up to 12 yea rs of ag e, w e recom mend the Vaux hall child restraint system 3 51.
48 Seats, Interior Belt tension ers In the event of a hea d-on or rear-end collision of a certain severity, the front seat belts are pulled down at the buckles and thereby tightened. Actuati on of belt tensioners is indicated by illum ina tion of control indica tor v; see next column. Trigg ered belt tensioners must be replaced by a workshop. Belt tensioners can only be trigg ered once.
Seats, Interior 9 Warning Hav e ca use of fa ult remedied immediately by a workshop . The system ’s integrated self-diagnostics allows faults to be quickly remedied. Imp or tant z Do not affix or place accessories or other objec ts within the deploym ent zone of the belt tensioners (in the area of the belt buckle). Do not make any modifications to belt tensioner components and the inertia real device bec ause this will invalidate the v ehicle type approval. 9 Warning Incorrect handling (e.g .
50 Seats, Interior Operation of the seat belts Fitting seat bel ts The seat belt must not b e twisted and m ust lie snugly a gainst the body. The back rest must not be tilted back too far (maxim um approx. 25°). Adjust the height so that the belt lies across the should er. I t must not lie across the throa t or upper a rm . Pull the belt out of the reel, guide it across the b od y (mak ing certain it is not twisted) and engage the latch plate in the buc kle.
Seats, Interior Child restraint system 3 Follow the usage instructions for the child restra int system . Alw ays comply with loc al or national regulations. In some countries, the use of child restraint system s is forbidden on certain seats. 51 Selecti ng the right syst em Y our child should b e tra nsported facing the rear in the vehicle for as long as possible.
52 Seats, Interior Permissible opti ons for fi tting a child safety sea t Weight and age cl ass1 ) Group 0: up to 10 kg or approx. 10 months On front p assenger sea t On a n out board seat in the rear row of seat s On m iddle seat2 ) in the r ear row of seats Group I I: 15 t o 25 kg or approx. 3 to 7 years X U+ U X U+ U X U U Group I II: 22 t o 36 kg or approx. 6 to 12 y ears 1) 2) U = univ ersally suita ble in c onjunction with three-point seat belt. + Group 0+: up to 13 kg or approx.
Seats, Interior 53 Note z Children under 12 years of a ge or under 150 cm tall m ust only trav el in an appropriate child restraint system on the seats in the rear row 3. z The covers of the Vauxhall c hild restraint system can be wiped clean. Mounting clips 3 for ISOFIX child restraint systems z Do not stic k anything on the child restraint sy stems a nd do not cover them with any other materia ls. z When transporting children, use the child restraint systems suitable for the child’s weight.
54 Seats, Interior Examples of events triggering the front airbag sy stem: z Impact against a non-y ielding obstacle: the front airbags are trigg ered at low vehicle speed. z Impact against a yield ing obstacle: (such as another vehicle): the front airbags are only triggered at a hig her vehicle speed. Airbag system The front airb ag system will be trigg ered : Front airb ag The front airbag system consists of one airbag in the steering wheel and one in the instrument panel.
Seats, Interior When trigg ered , the front airbags inflate in milliseconds to form a safety cushion for the d riv er and front passenger. The forward movement of the front seat occupants is c hecked, thereby sub stantially reducing the risk of injury to the upp er body and hea d. No im pairment of view will occur, because the a irb ags inflate and deflate so quickly that it is often not ev en noticed in an accident. 9 Warning Optimum protection is only provided with the seat in the proper position 3 37.
56 Seats, Interior Sid e a irbag 3 The side airbag system consists of a n airbag in each front seat backrest. This can be identified by the word AI RBAG. The side airbag system comprises: z an airba g with inflator in the ba ck of the driv er’s and front passenger seat respectively, The side a irb ag system w ill be triggered : z depending on the severity of the accident, z depending on the type of impact, z within the range shown in Fig.
Seats, Interior 9 Warning 57 9 Warning Keep the area in which the airbag infla tes clea r of ob structions. Hav e c ause of fault remedied imm ediately by a workshop. The sid e airbags w ill not be trigg ered in the event of The sy stem’s integrated self-diagnostics allows faults to b e q uick ly rem edied.
58 Seats, Interior Im portant z No objects or accessories must be placed in the area in which the airbag s inflate, as they could ca use injury when the com ponents are deployed. z Do not p la ce a ny objects between the airb ag systems and the vehicle occ upa nts. Danger of injury . Do not install a child restraint system 3 on the front passenger seat. Danger to life. 9 Warning As with any other object, child restraint systems must not be carried on a passenger’s lap . Danger to life.
Seats, Interior 59 Use of child restraint systems 3 9 Warning No c hild restra int system 3 m ay be installed on front passenger seat. Danger to life. Child restraint systems m ust only be installed on the seats of the rear row 3. O n versions without rear row of seats, no child restraint system m ay be insta lled on the front passenger sea t. Cigarette lighter 3 The cigarette lighter is in the centre console. Accessory socket With the ignition on, press in the cigarette lig hter.
60 Seats, Interior Do not ex ceed the maximum power consump tion of 120 w atts. Electrical accessories connected to the soc ket m ust comp ly with the electromagnetic compatibility req uirements la id d own in DIN VDE 40 839, otherwise v ehicle m alfunctions may occur. Do not connect any current-delivering accessories, e.g. electrica l charging devices or ba tteries. Ashtray 3 Ca ution To be used only for ash and not for combustible rubbish.
Seats, Interior Rear ashtra y 3 In the rear centre console. Stowage compartments To open, swiv el the cover up wards. Glove comp artm ent To op en, pull handle. To empty, lift the cover and pull the ashtray out upwards by its cov er. On the inside of the glove compa rtm ent cover there is a p en holder. The glove compartment should remain closed while driv ing . St owage com partm ent for glasses 3 O n driver’ s side: fold down to open.
62 Seats, Interior Stow age com partm ent in roof abov e t he front seats and sid e m esh p oc kets abov e the sliding doors 3 The stowage c om partment above the front seats can hold a maximum load of 15 kg. The m esh packets above the doors can only hold light objec ts. 9 Warning Secure objects to prevent them from falling out and causing injury. Stowa ge compa rtment 3 b eneath passenger seat Lift stowage c om partment by grasping the recessed edge and p ull it out. Maximum loa d: 1 kg.
Instruments 63 Instruments Control indicators .... ..... .... ..... .... .... ..... . Instrument display ... ..... .... ..... .... .... ..... . Information display . ..... .... ..... .... .... ..... . Warning buzzers.. .... ..... .... ..... .... .... ..... . Wind screen wiper .... ..... .... ..... .... .... ..... .
64 In struments I Engine oil pressure C ontrol indicator illuminates red It illuminates w hen the ignition is switched on and g oes out shortly after the engine starts. Illuminates when the eng ine is running Caution Eng ine lubrication may be interrupted. This ma y result in damage to the engine and/or locking of the driv e wheels. Flashes w hen the ignition is on Fault in the electronic immobiliser system; the engine ca nnot be started 3 19.
Instruments 65 The control indicator ! goes off a s soon as the self-cleaning op eration is comp lete. Diesel particle filter 3 110. T Winter prog ramm e of Easyt ronic 3 An indicator light illumina tes in the transmission displa y if the Winter programm e is activ ated 3 99. O Turn signal l ights Control indicator flashes g reen. The control indicator flashes if a turn signal or the haz ard warning flashers a re activated. Rapid flashing: light or associa ted fuse has failed. Replacing bulbs 3 144.
66 In struments r R u Fog tail light Control indicator illum inates yellow. Brake system, clutch system 3 Control indicator illuminates or flashes red. Anti -lock b rake system 3 C ontrol indicator illuminates red Illuminates when the fog tail light is on 3 82. Illum inated Illum inates when the ignition is switched on if the handbrake is applied 3 113. Illuminates while driving Fault in the anti-lock brak e system 3 112.
Instruments 67 Y Fuel lev el 3 C ontrol indicator illuminates and/or flashes yellow Illuminates Lev el in fuel ta nk too low . Flashes Fuel level is used up , fuel imm ediately. N ever let the tank run dry! Erra tic fuel sup ply can c ause the cata ly tic converter to overheat 3 108. Diesel engines: Bleed the fuel system if the fuel ta nk is allow ed to run dry 3 121. S Eng ine oi l level 3 Control indicator illum inates yellow. The engine oil level is c hecked automatically.
68 In struments Vehicles with clock in odometer To reset, press button with ignition switched on a nd trip odometer activated and hold d ow n for a pproximately 2 seconds. To switch between trip od om eter and clock display 3 give reset knob a brief p ress – see nex t page. Bottom line: O dometer Records the number of miles. S ervice interval d isplay 3 162. Instrum ent display Tachom eter Displays the engine rpm. Drive in a low engine speed range for each gear as much as possible.
Instruments Setting t he t ime On the clock display, press the setting knob on the instrument for ap prox . 2 seconds. The flashing va lue is set b y pressing briefly. Press for about 2 seconds again to switch to the nex t setting and at the end to exit setting mode. Time di sp lay in odometer 3 To sw itc h b etween trip odometer and time display 3 give reset button a short press.
70 In struments For physical reasons, the engine temperature gauge show s the coolant temperature only if the coolant level is adeq uate. During operation the system is pressurised. The temp erature ma y therefore rise briefly to ov er 100 °C. Coola nt temperat ure d isplay Coolant temperature gauge.
Instruments Transmission displ ay 3 Display of current gear or mode with Ea sy tronic 3 . R N Reverse gear Neutra l A 1-5 Automatic mode for Easytronic Manual mode, current gear w ith Easy tronic Ea sy tronic 3 3 96. Service di sp lay 3 If it illum ina tes in the odometer d isplay , book vehicle into a workshop as soon as possible for a service with maintenance. Maintenance, inspection system 3 162.
72 In struments FM 12:01 17,0°C FM 3 90,6 MHz REG AS RDS [TP] C Din 8:56 -5 ,5° C 07.04.2004 90.6 MHz TP 19,5° Information display Tripl e inform ation d isp lay 3 Display of time, outside tempera ture and date/infotainm ent system (when it is on). When the ignition is off, the time, date and outside tem perature can be disp la yed by briefly pressing one of the two buttons adjacent to the display.
Instruments 73 Automatic time synchronisation 3 The RDS signal of most VH F transmitters automatically sets the time. This can be identified by } in the displa y. Slippery road -2, 5°C 8 :56 5 ,5°C 07.04.2004 OK In vehicles with graphical information display 3, Sl ippery road is shown in the display as a w arning for icy roa d surfaces. There is no messa ge b elow -5 °C . 9 Warning Ca ution: The roa d surface may alrea dy be ic y even though the disp la y ind icates a few degrees above 0 °C.
74 In struments FM [TP] 19,5° C Din 90.6 MHz 19: 36 Graphical information display 3, selecting functio ns The g ra phic al information display depicts func tions and their m enus. Functions are selected and executed in the menu on the display using the four-way button, the m ulti-func tion button 3 on the infotainment sy stem or the buttons 3 on the steering wheel. To select w ith four-wa y but ton Select menu items via menus and with the buttons/four-w ay button of the infotainment system .
Instruments 7 FM [TP] C Din Settings Time, Date 75 19,5° 19:36 19:36 Language 90.6 MHz Units 10 . 07 . 2004 Contrast Day / Night 19,5° To sel ect with steering w heel but tons 3 Select menu options v ia the m enus using the b uttons. 19: 36 Functi on ranges Each function has a main page, w hich is selected from the upper row of the display (not in Infotainment system CD 30): z Audio, z Na vigation 3, z Telephone 3 .
76 In struments 7 Automatic tim e synchronisation 3 The RDS signal of m ost VHF transmitters autom atic ally sets the tim e. Time, Date Time Date 19,5° 19:36 19:36 10 . 07 . 2004 6 Synchron. clock automatical. Some transmitters do not send a correct tim e signal. I n such cases, we recommend that you sw itch off automatic tim e sy nchronisation. On infotainm ent systems with na vigation 3, time and date a re also ha rm onised upon receipt of a GPS sa tellite signal.
Instruments 7 13 Languages 19,5° 19:36 X Deutsch 7 Settings Language Español Units Nederlands Contrast F rançais Day / Night Italiano 6 Ign. logic Selections are indicated by a 6 in front of the m enu item . In systems with language version 3, when the la nguage setting of the display is changed , the system will ask if the m essag e language should also be changed - see infotainment sy stem instructions. 7 Contrast 19,5° 19:36 Time, Date English Select the desired language.
78 In struments Setti ng displa y mod e 3 Display brightness is independent of vehic le lighting. S ettings are m ade as follow s: Select menu item Day / N ight from the Setti ng s menu. The options are display ed. Autom atic: Adapted based on v ehicle lighting . Alw ays da y design: Black text on light back ground. Alw ays night desi gn: White text on dark back ground. Selections are indicated by a o in front of the m enu item . Ig ni tion logic 3 Setting , see infotainment sy stem instructions.
Instruments 79 Adj usta ble wip er i nter val To set the wiper interval to a v alue between 2 and 15 seconds: Stalk to interval operation $, stalk to §, wait for required interva l delay , Lev el to interval op eration again $ . The selected interval w ill remain stored until the next time it is changed or until the ignition is switched off. After switching on the ignition a nd m oving the stalk up, $ the interval is set to 7 seconds. Wi nd sc reen wa sh syst em Pull the stalk towards the steering wheel.
80 Ligh ting Lighting Versi ons w ith da ytim e r unning lights 3 If the light sw itch is set to 7, d ipped beam is activa ted without instrum ent illumination when the ignition is switched on. The daytime running lights turn off when the ignition is switched off. Follow the regula tions of the country in which you are driving w hen using da ytime running lig hts and front fog lights 3. Ex terior lights .. ..... .... ..... .... ..... .... .... ..... . Main beam, headlight flash . .... .... ..... .
Lightin g 81 Reversing lights The reversing lights come on when the ignition is on and reverse gear is eng aged. Main beam, headlight flash Turn signal lights Push stalk forward to switch from dipp ed beam to m ain beam . Stalk upwa rd s Stalk d ownwa rd s To switch to dipped beam, push stalk down again. If the stalk is moved pa st the resistance point, the turn signal lig ht remains on.
82 Ligh ting Fog tail ligh t r The fog tail light can only b e switched on if both the ignition and dipped beam/ parking lights are switched on. Operated with the r button. The fog tail light is deactivated when tow ing a carava n/trailer. Fro nt fog lights > 3 Hazard warning lights The front fog lights can only be sw itched on if both the ignition and lights are switched on. O perated with the ¨ button. O perated with the > button.
Lightin g 83 Comb o 0 1 2 = = = 3 = Front seats occupied All seats occupied All seats occupied and load compartment loaded Driver’ s seat occupied and full load in load com partment Comb o Crew v an Headlight range adju stment ? 3 Rotate the adjuster wheel to the required position to ad just the d ipped beam range to vehic le loading a nd prevent dazz ling.
84 Ligh ting Load c om part ment light ing 3 The loa d compartment lighting comes on when the load c om partment is opened. Autom atica lly reg ul ated centre console lig hting 3 S potlight in housing of interior m irror. Day lig ht-dependent, automatically regula ted centre console lighting with ignition switched on. Courtesy light 0 Autom atic i nt eri or light Com es on automatically when the vehicle is unlock ed with the remote control or when a door is opened.
Lightin g Battery discharge protectio n 3 Headlights when driving abroad Some consum ers such as the interior lighting switch them selves off after ap prox . 30 minutes if the ignition is off in order to protect the battery charge. The asymm etrical dipped b eam increases the field of v ision on the p assenger sid e of the lane. Misted light c overs The inside of the light bezels may mist briefly when sub jected to adverse wet a nd cold winter cond itions, strong ra in or after the vehic le is washed.
86 In fotain men t system Infotainment system Radio reception 3 Radio reception may be disrupted by static, noise, distortion or loss of rec eption due to z C hanges in distance from the transm itter, z multi-path rec eption due to reflection and z sha dowing . In fotain men t system 3 The infotainment sy stem is opera ted as described in the operating instructions. Radio reception 3 .... ..... .... ..... .... .... ..... . Infotainm ent system 3 . .... ..... .... .... ..... .
Info tainment system Mo bile teleph ones and radio equipment (CB) 3 The Vauxhall installation instructions and the opera ting guid elines provided by the telep hone ma nufacturer must be ob served when fitting and opera ting a mobile telep hone. Failure to do so could invalidate the vehicle’s opera ting permit (EU Direc tiv e 95/54/EC).
88 Climate c ontrol Climate control Heating , ventilation and air cond itioning system 3 ... ..... .... .... ..... . Air vents .. .... .... ..... .... ..... .... ..... .... .... ..... . Heating and ventila tion system ... ..... . Air conditioning system 3 ..... .... .... ..... . Air intake . .... .... ..... .... ..... .... ..... .... .... ..... . Air outlet.. .... .... ..... .... ..... .... ..... .... .... ..... . Pollen filter .. .... ..... .... ..... .... ..... .... .... ..... . Regula r operation ...
Climate control 89 Ad ditional vents Located in front of the windscreen, in front of the door mirrors and in the front footwells. Air vents At lea st one air vent must b e open while cooling 3 (air conditioning compressor) is on in order to prevent the evaporator from icing up due to lack of air movement. Com fortable ventilation of the interior is based on the position of the temp erature switch. To increase the air supply, set the fan to a higher speed a nd set the a ir distribution switch to M or L.
90 Climate c ontrol Heatin g and ventilation system Temperature Adjusted using left-hand rota ry knob. Red area Blue area = = wa rm cold The a mount of heat is dependent on the coolant temp erature a nd is thus not fully attained until the engine is w arm. Air flow Ad justed using centre rotary k nob. Air distribut ion Adjusted using right-hand rotary knob. x 1-4 V off selected fan sp eed The rate of air flow is determined b y the fa n.
Climate control 91 Hea ting For rapid warming of the p assenger compartment: z Turn the temperature switch clockw ise as far as it will g o (warm). z Set the fan to speed 3. z Set the air distribution sw itch to the desired position, preferab ly position J 3 90. The comfort and general well-b eing of the vehicle occupants a re to a large extent dependent on a suitable ventilation and heating setting. Vent ilation z Set the tem perature to the desired setting.
92 Climate c ontrol z Turn the temperature switch clockw ise as far as it will g o (warm). z Set fan to 3 or 4. z Set air distribution switch to V. z Activate heated rear window Ü. z O pen side air vents as required and direct them towa rd s side windows. z For simultaneous warming of the footwell, set air distribution switch to J.
Climate control 93 9 Warning The air recirculation sy stem minimises the entry of outside air. The humidity increa ses, and the windows can m ist up. The quality of the p assenger compa rtm ent air deteriorates which ma y cause v ehicle occupants to feel drowsy. Air distribution to V: the air recirculation system is a utomatically switched off to speed up w indow dem isting and p revent fogging. Cooli ng n O nly operate with the engine and fa n running. Ac tiv ate a nd dea ctiv ate w ith the n button.
94 Climate c ontrol Com fort setting z Set cooling n as desired. z Air recirculation system 4 off. z Set temperature switch as desired . z Switch on fan at desired speed. z Set air distribution sw itch to M or L. z Open vents as req uired. Tem perature switch in centre of adjustm ent range: wa rm er air will flow into the footwell and cooler air into the upper zone, with warmer air coming from the side air vents and cooler air from the centre vents.
Climate control Regular operation z Cooling n on, the a ir cond itioning com pressor automatically sw itches off in low outdoor tempera tures (ice formation), To ma ke sure that the AC com pressor is constantly work ing well, the cooling system 3 must be sw itched on several minutes once a month rega rd less of the weather or season. It is not possible to activa te cooling when outside temperatures a re low. z Turn the temperature switch clockwise. z Set fan to 3 or 4.
96 Drivin g and operatio n Driving and operation Ea sy tronic 3 .... ..... .... ..... .... ..... .... .... ..... . Manual transm ission .... .... ..... .... .... ..... . Driving hints .... ..... .... ..... .... ..... .... .... ..... . Sav ing Fuel, Protecting the Environment . ..... .... ..... .... ..... .... .... ..... . Fuels, refuelling .... .... ..... .... ..... .... .... ..... . Ca ta lytic converter, eng ine exhaust . . Hyd raulic brake sy stem ... ..... .... .... ..... .
Driving and o peration 97 Selector lev er in o (centre position) Moving the selec tor lever from N to o (centre position) while depressing the foot brak e time switches Ea sytronic to automatic m ode a nd engages first gear (second gear if winter prog ra mme is ena bled). "A" app ears in the gear display. Sta rting t he engine Briefly operate foot brake when starting the eng ine. The engine c an now be started in position N and with the foot brak e opera ted. N appea rs in the gear display .
98 Drivin g and operatio n Selec tor lever in + or + S hift to a hig her gear. S hift to a lower gear. If a higher g ear is selected when the running speed is too low, or a lower gear when the speed is too high, no shift is carried out. This prev ents the eng ine from running at too low or too high rev s. Selector l ev er i n A/M Switch b etween Automatic and M anual mode. In ma nual m ode, a gear can be selected manually b y tapp ing the selector lever to the + or - position.
Driving and o peration 99 Engine brak ing Automatic mode When driving d ow nhill, Ea sytronic does not shift into higher g ears until a fairly high eng ine speed has been rea ched. When brak ing, the transmission shifts down in good tim e. Manual m od e To utilise the engine braking effect, selec t a lower gear in good time when driving downhill. Winter progr amme T In the event of diffic ulties starting off on slip pery roads, p ress the T button ("A" and T a ppear in the transm ission d isplay ).
100 Drivin g and operatio n Vehicle storag e Ap ply the ha nd brake and rem ov e the key from the ignition. The previously selected gear (shown on the transm ission display ) remains selec ted. No gear is selected in selector lever p osition N. When the ignition is switched off, Easytronic no longer responds to movem ent of the selector lev er. If the ignition key is not removed, the battery m ay be discharged if the vehicle is then left to stand for a lengthy period of tim e.
Driving and o peration 101 3. C lean the transmission around the ca p (see Fig. 13739 S) so that no dirt can get into the opening when the cap is rem oved. 4. Rotate cap to slacken and remove by lifting upwards – see Fig. 13739 S. 5. Turn the a djusting screw clockwise using a flat-head screwdriver (vehicle tools 3 3 129) until clear resistance can be felt. The clutch has now been disenga ged.
102 Drivin g and operatio n Driving hints The first 600 mil es (1000 k m) Drive your vehicle at v arious speeds. Do not use full throttle. Never allow the eng ine to labour at low revs. Change gear frequently. Do not press the accelerator pedal more than approx. 3/ 4 in all gears. Do not drive faster than three quarters of max imum speed. Do not brake unnecessarily hard for the first 125 miles (200 km ).
Driving and o peration Sav e energy – m ore m iles Please observe the running-in hints on the previous pag e and the tips for sav ing energy on the following pa ges. Good, technica lly correct and economical driving ensures ma ximum durability and performance for your vehic le. O verrun cut-off The fuel supply is autom atically cut off during overrun, e.g. when the vehicle is driven w ith a gear engaged but no throttle application.
104 Drivin g and operatio n Saving Fuel, Protecting the Environment Trend-set ting technology Env ironmenta lly friendly and mainly recy clable materia ls were used when y our vehic le was being developed and manufactured. The production methods used to m ake your vehicle are also env ironmenta lly -compatible. Recycling of production wastes keeps the circulation of material closed. Reduction of energy a nd water requirements a lso help s to conserve natural resources.
Driving and o peration O verrun z The fuel supply is automatically shut off during ov errun, e. g. when the vehicle is being driven down long gradients or when braking 3 103. z To enable the overrun cut-off to come into action and sav e fuel, do not accelerate or d epress the c lutch pedal during ov errun. Corr ect gear sel ec tion z High revs increase engine w ear and fuel consumption. z Do not race your engine. Avoid d riv ing at high engine speeds. Making use of the tachom eter helps to save fuel.
106 Drivin g and operatio n Fuels, refu elling Fuel c onsum ption Fuel consump tion is determined und er specific d riv ing cond itions 3 175. Special equipment increases the weight of the v ehicle. As a result, they can increase fuel consump tion and reduce the specified max imum speed. There is increased friction betw een engine and transmission parts during the first 600 miles (1000 k m). This increases fuel consump tion. Fuel for petrol engi nes Only use unleaded fuel that complies with DIN EN 228.
Driving and o peration 107 C orrect filling depends to a large extent on proper operation of the fuel disp ensing pump: 1. Fully insert the pump nozz le and switch it on. 2. After the automatic cut-off, the nominal capacity of the fuel tank can be obtained by topping up with two d oses of fuel. Mak e sure the noz zle is fully inserted. To c lose, place fuel filler cap in position and turn, overcom ing the resistance until the ratchet on the cap engages audibly.
108 Drivin g and operatio n z In the event of misfiring, uneven engine running, a clear reduction in engine performa nce or other unusual problems, have the cause of the fa ult rec tified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low. z If unburnt fuel enters the catalytic converter of a petrol engine, this m ay result in overheating and irrepa ra ble dam age to the cataly tic converter.
Driving and o peration 109 If it illuminates briefly, but does not rec ur, it is of no significance. If A illuminates, there may b e water in the diesel fuel filter 3. Ha ve the fuel filter checked for water residue by a workshop 3 166. If it flashes after the ignition is switched on, there is a fault in the im mobiliser sy stem. The engine c annot be started 3 19. Engine exhaust 9 Warning Ex haust ga s control indicator Z Illuminates when the ignition is switched on and during the start a ttempt.
110 Drivin g and operatio n Diesel p artic le fi lter 3 The d iesel pa rticle filter system filters harmful soot pa rticles out of the ex ha ust gases. The sy stem includes a self-cleaning func tion that run automatically d uring driving. The filter is cleaned by b urning off the soot particles at high temperature. This process takes place automa tic ally under set driving conditions and may take up to 25 minutes. Fuel consumption may be higher during this period.
Driving and o peration 111 Maintenance Have all maintena nce work c arried out at the specified intervals. We recomm end that y ou entrust this work to your Vauxhall Authorised Repairer, who ha s p roper equipment and trained personnel available. Electronic testing sy stems permit ra pid diagnosis and remedy of faults.
112 Drivin g and operatio n For vehicles with Easytronic 3, the control indicator flashes for a few second s w hen the ignition is turned off if the handbrake i s not applied. To ensure the full p edal trav el c an be utilised, especially in c ase of a fault in one of the brak e circuits, there must b e no mats in the v icinity of the pedals 3 103. When the engine is not running, the sup port of the brak e servo unit d isappears once the brake pedal has been depressed once or tw ic e.
Driving and o peration 113 Self test ing When the engine is started and the vehicle starts off, the system performs a self-check, whic h may be a udib le. Fault 9 Warning If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heav ier than normal. The advantages of ABS are no longer ava ila ble. During ha rd braking, the vehicle can no longer be steered and may swerve. Cont rol indica tor u for ABS It illuminates for a few seconds when ignition is switched on.
114 Drivin g and operatio n Brake assist Wheels, tyres When the brake peda l is rap idly and forcefully depressed, the vehicle is automatically braked with ma ximum b ra ke force a mplification in order to obtain the shortest possib le brak ing distance during full-on bra king (brake assist). Suitable ty res or limitations 3 179. Maintain steady pressure on the brak e pedal for as long as full-on brak ing is to continue.
Driving and o peration 115 Alw ays inflate the spare wheel 3 to the pressure specified for full load. Do not reduce ty re pressure when the tyres are wa rm. O therwise the pressure may drop b elow the perm issible minimum when the tyres cool down. After having chec ked the tyre pressure, tig hten the va lv e ca ps using the v alve cap key . Incorrect infla tion pressures will imp air safety, v ehicle handling, comfort and fuel economy and will increase tyre wear.
116 Drivin g and operatio n Tyre cond ition, w heel condi tion Drive over edges slowly and at right angles if possible. Driving over sha rp edg es can cause tyre and wheel damage. Do not trap tyres on the kerb when pa rk ing. Tr ead depth Check tread depth regularly. Regula rly check the wheels for damag e. Seek the assistance of a workshop in the event of dam age or unusua l wear. The leg ally permissible minimum trea d depth (1.
Driving and o peration 117 Tyre designations Meanings: Winter tyres 3 Instructions on fitting new tyres 3 114. e.g. 175/70 R 14 79 T Limitations 3 179. z Ty res age, even if they are little used or not used at all. We recomm end ty re replacement no la ter tha n every 6 years. 175 = 70 = Winter tyres improve driving safety a t temperatures b elow 7 °C . z Nev er fit used ty res the previous history and use of which you do not know.
118 Drivin g and operatio n Wheel trims must not imp air brak e cooling . Remove the wheel trims when using tyre chains 3 130. Remove the wheel trims if fitting tyre chains 3. Tyre cha ins may only be used at sp eeds up to 30 mph (50 km/h). When tra velling on roads that are free of snow, they may only be used for brief periods. 9 Warning Use of unsuitable tyres or wheel trim s could lead to sud den loss of a ir and thereby ac cidents. 9 Warning Dama ge m ay lead to ty re blowout.
Driving and o peration Roo f racks 3 Towing equipment 3 For safety reasons and to avoid roof dam age we recommend using the Vauxhall roof rac k system that is approved for your vehicle. Only use towing equipment tha t has b een approved for your vehicle. Entrust retrofitting of towing equipment to a work shop. It may be necessary to m ake cha ng es that affect the cooling sy stem, heat shields or other equip ment. Follow the usa ge instructions for the roof rack. Remove the roof rack when not in use.
120 Drivin g and operatio n Coup ling socket l oa d The c oupling socket load is the load exerted by the carav an/trailer on the coupling ball. It can b e varied by changing the w eight distribution when loa ding the carava n/trailer. C aravans/trailers with LED turn signa ls require a p rov ision that make bulb replacem ent as with stand ard bulbs possible. Handling is greatly influenced by the loading of the caravan/tra iler.
Self-help, vehicle care Self-help, vehicle care Diesel fuel system, bleeding . .... .... ..... . Bonnet ..... .... .... ..... .... ..... .... ..... .... .... ..... . Starting the engine with jump leads 3 .. .... .... ..... .... ..... .... ..... .... .... ..... . Towing ..... .... .... ..... .... ..... .... ..... .... .... ..... . Warning triangle ¨ 3 and first-aid kit (cushion) + 3 .... .... ..... .... ..... .... .... ..... . Spa re wheel 3 . ..... .... ..... .... ..... .... .... ..... .
122 Self-help, vehicle care Starting the engine with jump leads 3 Do not start by quick cha rger or by pushing or towing. A vehicle with a d ischarged battery ca n be started using jump leads and the battery of another v ehicle. 9 Warning Lift the safety catch and op en the bonnet. Dirt or snow on the bonnet may drop onto the windscreen when the bonnet is opened and block the air intake. Air intake 3 95. Sec ure the b onnet support. Before closing the bonnet, press the supp ort into the holder.
Self-help, vehicle care 123 z Use a booster battery with the same voltage (12 volts). Its capacity (Ah) must not be much less than tha t of the discharged battery. z Use jump leads with insulated terminals and a cross section of at least 16 mm 2 (25 m m2 for diesel engines). z Do not disconnect the d ischarged battery from the vehicle. z Sw itch off all unnecessary electrical consumers. z Do not lean over the battery during jump starting. z Nev er expose the battery to naked flam es or sparks.
124 Self-help, vehicle care Route the lead s so that they cannot catch on rotating parts in the engine compartment. To start the eng ine: 1. Start the engine of the vehicle p rov id ing the jump start. 2. After 5 minutes, sta rt the other engine. Start attem pts should be made at intervals of 1 m inute not last longer than 15 seconds. 3. Allow both engines to idle for approx. 3 m inutes w ith the lead s c onnec ted. 4. Switch on electric loads (e.g .
Self-help, vehicle care Switch on ignition to release steering colum n lock and to permit opera tion of brake lights, horn and windscreen wiper. When the engine is not running, consid erably more force is needed to brak e and steer. Manua l tra nsmission in neutral; Easy tronic 3 in N. To prevent the entry of exhaust fum es from the tow ing vehicle, switch on the air recirc ulation 3 and close the wind ow s. Ca ution Driv e slowly. Do not driv e jerkily. Excessive tractive force ca n damage the vehicle.
126 Self-help, vehicle care Towing another vehicle Attach a tow rope 3 – or better still a tow rod 3 – to the rear towing ey e on the right side of the vehicle underbody, but nev er to the rear ax le. The towing eye is only to be used for towing and not for vehic le recovery. C aution Drive slowly . Do not drive jerkily . Ex cessive tractive force can damag e the vehic le.
Self-help, vehicle care Com bo Crew van The w arning triangle and the first aid cushion or box are k ept in the compartment behind the driver’s seat. When the vehicle is being loaded, p lease ensure that nothing protrudes over the bottom edge of the opening. Diseng age flap 3 by p ressing retaining lug and rem ov e. 127 3 The spare wheel is stored benea th the floor. 3. Unhook the catch and lower the spare wheel holder. 1.
128 Self-help, vehicle care General i nformati on Depend ing on the version, the spare w heel may be d esigned for use as a temporary spare 3. The temporary spare is designated by a sticker on the rim. Follow the instructions on this pag e and on 3 118, 3 179. Not es on temp orary sp are wheel 3 z Using a temp orary spare w heel may chang e the driving behaviour of the vehicle, particularly if using winter tyres 3 . Rep la ce d efec tiv e ty re as quickly as possib le, b alance w heel and fit to vehicle.
Self-help, vehicle care 129 Inform ation on di rec tional tyres 3 Fit direc tional tyres such that they roll in the direc tion of travel. The rolling d irection is indicated by a symbol (e.g. a n arrow) on the sidewall. The following applies to tyres fitted opposing the rolling direction: z Driv ing conditions ma y be a ltered. Have the defective tyre replaced as soon as possible. z Do not d riv e faster than 50 mph (80 km/h). z Driv e esp ecially carefully in wet and snowy w eather.
130 Self-help, vehicle care Changing wheels z Use the ja ck only to change wheels. There m ay be a tyre rep air kit instead of a spare wheel 3 135. z If the ground on which the vehicle is standing is soft, a solid board (max . 1 cm thick ) should be placed under the jack. Make the following prep arations and ob serve the follow ing information: z Park the v ehicle on a level, firm and nonskid surface. The front wheels must be in the straight-ahead position.
Self-help, vehicle care 1. Prise off the hub cap using a screwdriver, positioning the sc rewdriver at the recess at the side of the hub cap. Vehicle tools 3 129. Pull off the wheel trim with the hook 3. Vehicle tools 3 129. O n some versions, the w heel trim is rem oved tog ether w ith the wheel bolts. For wheel trims with visible wheel bolts 3, the trim can rem ain on the wheel. The reta ining rings 3 a t the wheel bolts must not be remov ed.
132 Self-help, vehicle care Alloy wheels w ith a nti-theft lock 3: unscrew the hub cap with anti-theft k ey and remov e it. Vehic le tools 3 129. 2. Push the wheel bolt wrench 3 on as far as possible and slacken the wheel b olts half a turn. 3. The jacking p oints are marked.
Self-help, vehicle care 133 5. Unscrew the wheel bolts. On some versions, the wheel trim is rem ov ed together with the wheel bolts. If there are lock wa shers 3 on the wheel bolts, these m ust not be rem ov ed. 6. Changing wheels. Notes on spare w heel 3 127. Notes on temp orary spare wheel 3 118, 3 128, 3 179. 4. Pre-adjust the jack 3 to the required height. Position the jack arm in the front or rear so that the jack claw (arrow in picture) grips the vertical web in the recess.
134 Self-help, vehicle care 9. Push the wheel bolt wrench 3 on as far as possib le and tig hten crosswise. Tightening torque is 110 Nm. Alloy wheels 3 : put hub cap on a nd engage, inserting pin on rear of hub ca p into required hole in wheel. Alloy wheels with anti-theft lock 3: Put hub ca p on. Insert and tighten antitheft lock 3. 10. Before refitting the w heel trim, clean the wheel around the retaining clips. Valv e sym bol 3 on back of wheel trim must point towards va lv e on wheel. 7.
Self-help, vehicle care Tyre repair kit 3 Minor d amage to the tyre tread or sidewall can be repaired with the tyre repair kit. Do not rem ov e the foreign body from the tyre. Tyre d amage exceeding 4 mm or that is on the rim cannot be repaired with the ty re rep air kit. 9 Warning Do not drive faster than 50 m ph (80 k m/h). Do not use the temporary spare wheel for a leng thy period. Steering and handling m ay be affected. Imp ortant information 3 138.
136 Self-help, vehicle care 4. Screw the compressor air hose to the connection on the sealant bottle. 5. Fit the sealant bottle in the retainer on the compressor. Set the compressor near the ty re in such a way tha t the sealant b ottle is up rig ht. 6. Remove the v alve cap from the defective ty re. 7. S crew the filler hose to the tyre valve. 8. The sw itch on the compressor must be set to §. 9. Plug the compressor connector into the ac cessory socket or the cigarette lighter socket.
Self-help, vehicle care 137 Drain excess tyre pressure with the button over the pressure indicator. Do not run the com pressor for more than 10 minutes - see "Imp ortant information" 3 138. 15. Detach the ty re repair kit. Screw the filler hose to the free connection on the sea lant bottle. This prev ents sealant leakage. S tow the ty re repair kit in the load compartment. 16. Wipe away any sea la nt spill with a cloth.
138 Self-help, vehicle care Im portant The d riv ing comfort of the rep aired ty re is greatly lessened. Hav e such tyres rep laced. If the compressor makes abnorm al noises or heats up greatly, switch it off for at least 30 minutes. The integrated safety valv e opens a t a pressure of 102 psi (7 bar). Protect the compressor from m oisture and rain. The sealant can only be stored for approx. 4 years. After this tim e, the sealing properties can no longer be guaranteed.
Self-help, vehicle care 139 Alway s use fuses with the correct current va lue. This is shown on eac h fuse, and is also indicated by the fuse colour and the plug-in location in the fuse box . Different versions of fuses are used. Before replac ing a fuse, turn off the respective switch and the ignition. Slot fuse-gripping tool onto fuse and withdraw it. A defective fuse can be recognized by its melted wire. A new fuse should only be installed after the cause of the trouble has been rectified.
140 Self-help, vehicle care Fuses and the m ost importan t circuits they protect Some circuits m ay be protected by severa l fuses. The figures on pag es 140, 141 depict the fuse b ox es of vehic les with engine Z 13 DTJ 1) . Fuse boxes of other engines are dep ic ted on pa ges 142, 143. No. 1 2 1) Circuit Central control unit Engine control unit Sa les desig nation 3 173. No.
Self-help, vehicle care No. 26 No. 19 20 Elec tric wind ow (rig ht) – Circuit 21 22 – Central control unit, immobiliser 23 24 Windscreen wiper Infotainment sy stem, information display, lig ht switch, courtesy light, instruments, EPS No.
142 No. 27 Self-help, vehicle care Circuit Seat heater (left) No. 28 29 Ci rcuit ABS Rear window wiper No.
Self-help, vehicle care No. 38 39 Left tail light, left pa rk ing light Right tail light, right parking light Circuit 40 41 Bra ke lig hts Front fog lights 42 43 Fog tail light Main bea m (left) 44 45 Main bea m (right) Ventilation fan 46 47 Engine control unit Heated rear window 48 49 Starter EPS 50 51 ABS Petrol engine: Easytronic Diesel eng ine: engine control unit No. 52 Ci rcuit Radiator fan No.
144 Self-help, vehicle care Bulb replacement Switch off the ignition and turn off the relevant switch or close the doors. O nly hold a new bulb at the base! Do not touch the bulb glass with your b are hands. The replacement bulb must be in accordance with the d ata on the ba se of the defective bulb . Do not ex ceed wattage given on bulb base. To change the bulbs on the left side, open the fuse b ox cover.
Self-help, vehicle care 3. Push bulb on plug connec tor downward. 5. Detach plug c onnec tor from bulb base. 4. Rem ov e b ulb with connector from reflec tor housing. 7. I nsert the bulb with connector so that the lug engag es in the recess in the reflector. 6. Plug the plug onto the new bulb. 8. Place head lig ht protective cover in position and close. 145 Ma in beam 1. Op en bonnet a nd engage sup port. 2. Rotate the cap anticlock wise and rem ov e.
146 Self-help, vehicle care 3. Detach p lug connector from bulb. 5. Remove bulb from reflector housing. 4. Disengage spring w ire clip from retaining lugs by moving it forward and sw iv elling it to the side. 6. When fitting the new bulb, insert lugs in the reflec tor recesses. 7. Engage spring wire clip, plug connector onto bulb. 8. Place head lig ht protective cover in position and close. Park ing lig hts 1. Op en bonnet a nd engage sup port. 2.
Self-help, vehicle care 4. Rem ov e side light bulb mounting from reflec tor. 7. I nsert b ulb socket in reflector. 5. Rem ov e b ulb from socket. 9. Place head lig ht protective cover in position and close. 6. Insert new bulb . 8. Attach connector to m ain beam bulb. 147 Front turn signa l lights 1. Op en bonnet a nd engage sup port. 2. Rotate bulb hold er to left and disengage.
148 Self-help, vehicle care 3. Push bulb into holder a little, rotate left and rem ove. 4. Insert new bulb . 5. Engage holder into reflector by rotating to the right. Ellipsoidal headlight system 3. Detac h plug connector from bulb. Di pped beam Head lig ht system with separate bulbs for dipped beam (inner bulbs) and main beam (outer bulb s). 4. Disengage the sp ring wire clip from the lugs and swivel it aside. 1. O pen bonnet and eng age support. 2.
Self-help, vehicle care 149 Ma in beam, p arki ng lights Hav e b ulb replacement carried out by a workshop. Side turn signal lights Hav e b ulb replacement carried out by a workshop. Front fog lights 3 Hav e b ulb replacement carried out by a workshop. Front turn signal lights 1. Open bonnet and engage supp ort. 3. Push b ulb into holder a little, rota te left and remove. 2. Rotate b ulb holder to left a nd disengage. 4. I nsert new bulb. 5. Engage holder into reflector by rotating to the right.
150 Self-help, vehicle care Tail lights 1. Disenga ge c ov er by pressing retaining lugs and remove. 2. Deta ch plug connector from bulb mounting . 3. Grip the bulb housing from the outside, slacken the two knurled nuts using the wheel bolt spanner 3 and unscrew by hand. 4. Deta ch bulb housing. 5. Press retaining lugs on bulb mounting together and rem ov e bulb m ounting, as shown in Fig. 13726 S.
Self-help, vehicle care Number plate lights 1. Unscrew both screws. Remove light insert. 2. Press bulb slig htly towards spring c lip and remove. 3. Insert new bulb. 4. Insert light insert and sec ure using a screwdriv er. Courtesy lights Front courtesy l ight 1. Prise light out of recess using a screwdriver.
152 Self-help, vehicle care 2. Press bulb slightly towards spring clip and remov e. 3. Insert new bulb. 4. Insert lig ht in op ening and eng age in position. Front c ourtesy light with read ing light s 3 1. Disengage and remove lens at the position shown in Fig. 11669 S using a screwdriv er. 2. Remove bulb from socket. 3. Insert new b ulb. 4. Mount lens a nd engage in position.
Self-help, vehicle care Instrument ill um ination, Informat ion display illum ination 3 Have bulb replacem ent carried out by a work shop. Load com partm ent light 3 1. Prise lig ht out of recess using a screwdriver. 2. Press bulb slightly towards spring clip and remov e. 3. Insert new bulb. 4. Insert lig ht in op ening and eng age in position.
154 Self-help, vehicle care Vehicle care When caring for your vehicle, observe all nationa l environmental regulations, particularly when washing it. Regula r, thorough care helps to imp rov e the a ppearance of your vehicle and maintain its value ov er the years. It is also prerequisite for warranty claim s for any paint or corrosion dam age. The following pages conta in tips for vehicle ca re which, if used properly, w ill help comb at the unavoidable damag ing effects of the env ironment.
Self-help, vehicle care Windows and windscreen wip er b lades Use a soft lint-free cloth or chamois leather together with window cleaner and insect rem ov er. Engine com partm ent Clea n painted surfa ces in the engine compartment lik e any other painted surface. When c leaning the rear w indow, m ake sure the heating element inside the window is not damag ed. For best results, wa sh and w ax the engine compartment before a nd after winter.
156 Service and maintenance Service and maintenance Scheduled maintenance The service intervals app ly to normal op erating conditions. For extreme op erating conditions, 3 160. Serv ic e interv al display 3 162. Service interv als Every 20,000 miles (30,000 k m) or annually, whic hever occurs first. Scheduled m aintenance .. ..... .... .... ..... . Additional service work .... ..... .... .... ..... . Recommended fluids and lubricants . Inspection system .... ..... .... ..... .... .... ..... .
Servic e and mainten ance 157 Servi ce plan after y ear 1 ) miles (x 1000) 1 ) km (x 1000) 1 ) Service w ork 1 20 30 x 2 40 60 x Check and correc t windscreen wip er, w indscreen wash sy stem and headlight wash sy stem x x Check and correc t coola nt level and frost protection (pale orange) 2) Note freeze protec tion tempera ture in the S ervice and Warranty Booklet (confirmation box) x Check water hoses for leaks and chec k to mak e sure they are firmly sea ted x Visually insp ect control, lig
158 Service and maintenance Service w ork ⊕ after y ear 1 ) miles (x 1000) 1 ) km (x 1000) 1 ) 1 20 30 2 40 60 3 55 90 4 75 120 5 100 150 Replac e toothed belt and tension roller Z 17 DTH Change engine oil and oil filter ⊕o Drain water from d iesel fuel filter (with high humidity and/or low fuel grade) Replac e and drain water from fuel filter, Z 13 DTJ, Z 17 DTH Check and ad just parking b ra ke (wheels unladen); v isually inspec t wheel suspension and spring suspension front and b ack, b ra ke
Servic e and mainten ance Servic e w ork ⊕ a fter year 1) miles (x 1000) 1) km (x 1000) 1) 1 20 30 2 40 60 3 55 90 4 75 120 159 5 100 150 Visually inspect steering bellows, trac k rods and ax le drive x x x x x Check track-rod ends and suspension ball joints x x x x x Change brake and clutch fluid (Easytronic) every 2 years Undo wheel mounting and tighten to 110 N m torque During assem bly, lightly lub rica te wheel bolt tap ers with grease or oil x Check tyre condition; check and cor
160 Service and maintenance Additional service work Add itional w ork ⊕ Additional work is work which is not req uired for ev ery service but can be carried out along with a regular service. Time allowances for such w ork are not included within the scope of a regular service and m ust be accounted for separately. However, it is more cost effective to carry out this work as part of a planned service than to hav e it done separately.
Servic e and mainten ance Eng ine oi l Engine oil is identified b y its grade and viscosity . When choosing which engine oil to use, g ra de is more important than viscosity . Top ping up engi ne oil Oil from different manufacturers and of different brands can be mix ed prov iding they m eet the spec ified eng ine oil criteria (g ra de a nd viscosity). The new eng ine oil GM-Dex os 2 is of the highest quality available at the moment.
162 Service and maintenance The service interval display takes account of off-the-road p eriods during which the battery is d isconnected. Flexible serv ice interva l 3 The length of the service intervals is based on several parameters stemming from usage. For this reason, various engine-spec ific data is continually gathered and is used to calculate the remaining distance until the next serv ic e.
Servic e and mainten ance 163 Vauxhall genuine parts and ac cessories We recommend that you use " Vauxhall genuine parts and accessories" and conversion parts approved ex pressly for your vehicle ty pe. These parts have undergone special tests to establish their reliab ility , safety and specific suitability for Vauxhall vehicles.
164 Service and maintenance Engine oil O n vehicles w ith engine oil level check 3, the engine oil level is m onitored automatically 3 67. We recommend that you check the engine oil level before starting a long journey. C aution Imp ortant: It is the owner’s resp onsibility to maintain the correct lev el of an appropriate quality oil in the engine. Check with the v ehicle on a level surface. The engine must be at operating temperature and switched off for a t least 5 minutes.
Servic e and mainten ance We recommend that you use the sam e engine oil as was used the last tim e it w as topped up. The engine oil lev el must not ex ceed the MAX mark on the dipstick. Ca ution If there is too much engine oil, the ex cess must b e drained or suc tioned out. 165 The amount must be between the M IN and MAX m arks 3 182. Fit the ca p on straight and tig hten it.
166 Service and maintenance Diesel fuel filter Coo lant O n the event of eng ine oil change, have fuel filter checked for possible water residue by a workshop. The coola nt provides antifreeze p rotection down to approx. -28 °C . Ca ution Illumination of A indicates wa ter in the fuel filter 3.
Servic e and mainten ance Top up with antifreez e. I f no antifreeze is available, fill with clean tap water or distilled water. Have the antifreeze concentration checked. Have the cause of coolant loss rectified by a workshop. Ca ution Too low a coolant lev el can c ause engine d amage. Fit the cap on straight and tighten it. Coola nt level In a closed cooling sy stem, there is hardly any loss. When the cooling sy stem is cold, the level of coolant should lie above the KA LT/CO LD mark.
168 Service and maintenance Brake fluid 9 Warning Brake fluid is poisonous and corrosive. Do not allow it to come into contact with eyes, skin, fab rics or pa inted surfaces. Cha ng ing bra ke fluid Brake fluid is hy groscopic, i.e. it absorbs water. If the brakes b ecome hot, suc h as when d riv ing on long downhill stretches, vap our bubb les can form in the water, which can have an extrem ely adverse effect on braking power (depending on the proportion of w ater).
Servic e and mainten ance 169 Parking up the vehicle for more tha n 4 weeks can lead to b attery discharge. Disconnect the negative terminal of the vehicle b attery. Ensure the ignition is switched off before connecting or disconnecting the vehicle battery. Note The Va ux ha ll a larm sy stem 3 siren must be deactiv ated a s follows: switch the ignition on then off, disconnect the vehicle’s battery within 15 seconds.
170 Service and maintenance Parking t he vehicle up for a long period of time If the vehicle is to be laid up for several months, the following work should b e undertaken to prev ent dam age. z Wash and wa x the vehicle 3 154. z Have the wax in the engine com partment a nd underbody checked. z Clean and preserv e rubber seals. z Change engine oil. z Check antifreeze and c orrosion protection 3 166. z Check the coolant lev el; top up antifreeze if necessary 3 167. z Drain the windsc reen wash system .
Technical data 171 Technical data Vehicle data .... ..... .... ..... .... ..... .... .... ..... . Engine data. .... ..... .... ..... .... ..... .... .... ..... . Performance (approx. mph / km/h) .. . Fuel consump tion, CO 2-em issions ..... . Fuel consump tion (l/100 km), CO 2 emissions (g/km) for ty re width of up to 185 mm .... ..... .... ..... .... ..... .... .... ..... . Weights, pay loa d and roof load .. ..... . Tyres ... ..... .... .... ..... .... ..... .... ..... .... .... ..... .
172 Tec hnic al data Eng ine code and eng ine number. Marked on engine block a t left side of engine in petrol engines, and beneath diesel injection pump at right side of eng ine in diesel engines.
Technical data Engine data Sales designation Eng ine identifier code 1.4 TWINPOR T Z 14 XEP 1. 3 CDTI Y 13 DT 1.3 C DTI Z 13 DTJ 1.
174 Tec hnic al data Performance (approx. mph / km/h) Eng ine speed1) Max imum 5-speed ma nual transmission Easytronic 1) 2) Z 14 XEP Y 13 DT Z 13 DTJ Z 17 DTH 102/164 – 93/150 – 94/152 2 ) 94/152 2 ) 106/170 – The ma xim um s peed is a ch ieva ble with a m aximum of h alf p ayloa d. Optiona l eq uipm ent m ay reduce th e specified m aximum speed of the vehicle. Sp ecific version with electronic speed limitation a t 78 m ph (125 km/h ).
Technical data Fuel consumption, CO 2 -emissions Directive 80/1268/EEC (last c hanged by 2004/3/EC) has applied for the measurement of fuel consumption since 1996. The direc tiv e is oriented to actual driving practices: Urba n driving is rated at approx. 1/ 3 and off-road driv ing with approx. 2/ 3 (urban and extra-urban consumption). C old sta rts a nd acceleration phases are also taken into considera tion. The specification of CO 2 emission is also a constituent of the directive.
176 Tec hnic al data Fuel consumption (l/100 k m) , CO 2 emissions (g/km) for tyre w idth of up to 185 mm Eng ine Z 14 XEP Y 13 DT Z 13 DTJ Z 17 DTH Manual / Ea sytronic transm ission urban extra-urb an total CO 2 7.9/– 5.2/– 6.2/– 148/– 6.5/– 4.5/– 5.3/– 143/– 6.1/ 5.9 4.5/ 4.5 5.1/ 5.0 134/135 6.6/– 4.4/– 5.
Technical data Weights, payload and roof load The p ayload is the difference between the permitted g ross vehicle weight (see identification plate 3 171) and the EC kerbweight. To ca lc ulate the kerbweight, enter the data for your vehicle below: z Kerb weight from Ta ble 1 3 178 z Weight of heavy accessories from Ta ble 2 3 178 Total +... ..... .... .. kg +... ..... .... .. kg =... ..... .... .. kg is the EC k erbweight.
178 Tec hnic al data Weights (k g) , Table 1, kerbweight1 ) Com bo Crew van Engine M anual transmission Easytronic wi thout/w ith ai r condit ioning Z 14 XEP 1190/1350 – Y 13 DT 1285/1420 – Z 13 DTJ 1285/1420 1285/1420 Z 17 DTH 1320/1455 – Weights (k g) , Table 1, kerbweight Com bo Engine M anual transmission Easytronic wi thout/w ith ai r condit ioning Z 14 XEP 1235/1265 – Y 13 DT 1325/1355 – Z 13 DTJ 1325/1355 1325/1355 Z 17 DTH 1365/1395 – Weights, Table 2, heavy acces
Technical data Tyres Not a ll tyres ava ila ble on the market currently meet the structural requirem ents. We recommend that you consult a Vauxhall Authorised Repairer concerning suitab le tyre mak es. These ty res have und ergone special tests to establish their reliab ility , safety and specific suitability for Vaux hall vehicles.
180 Tec hnic al data Tyre pressure in psi / bar Com bo Crew van Ty re pressure w ith load of up to 2 p ersons and 100 kg load Tyre pressure for full load Front Rear Front Rear 35/2.4 35/2.4 35/2.4 51/3.5 Engine Tyres Z 14 XEP 175/70 175/65 185/55 185/60 Y 13 DT 175/70 R 1421 ), 185/60 R 15, 185/55 R 1554 ) 35/2.4 35/2.4 35/2.4 51/3.5 Z 13 DTJ 175/70 175/65 185/55 185/60 R 14 1)2 ), R 14 2), R 15 3)4 ), R 15 35/2.4 35/2.4 35/2.4 51/3.
Technical data Tyre pressure in psi / bar Com bo Ty re pressure w ith load of up to 3 persons Engine Tyres Z 14 XEP 175/70 175/65 185/55 185/60 185/65 195/45 195/50 Y 13 DT 175/70 R 14 1), 185/55 R 15 3), 185/60 R 15 Z 13 DTJ 175/70 175/65 185/55 185/60 185/65 Z 17 DTH 185/60 185/55 185/65 195/50 all T 115/70 R 16 (Temp orary sp are wheel) 5) 1) 2) 3) 4) 5) Tyre pressure for full load Front Rear Front Rear 35/2.4 35/2.4 35/2.4 51/3.5 35/2.4 35/2.4 35/2.4 35/3.
182 Tec hnic al data Capacities (approx. in litres) Eng ine oi l Eng ine Z 14 XEP Y 13 DT Z 13 DTJ Z 17 DTH Incl. filter 3. 5 3.2 3.5 5. 0 Betw een MIN a nd MAX 1. 0 1.0 1.0 1.
Technical data Dimensions (m m) C ombo C rew v an Comb o O verall length 4322 4322 O verall w id th 1684 1684 Width with two ex terior mirrors 1892 1892 Height at kerbweight 1801 1801 Length of load comp artm ent 1787 1) /27002) 10203 )/1664 4) /27 00 2) Width of loa d compartment; without/with 1/with 2 sliding doors min. width between wheel housings 1348/1399/1449 1107 –/1399/1449 1107 Max .
184 Tec hnic al data Mounting dimensions of towing equipment with fixed coupling ball bar All dimensions relate to trailer towing equipm ent app rov ed b y Vauxhall. Dimension mm A 71 B 929 C 515 D 506.3 E 274.3 F 149 G 401.7 H 384 I 398 9 Warning O nly use towing eq uipm ent app rov ed for your vehicle. We recomm end entrusting retrofitting of towing equipm ent to y our workshop.
Index Index A ABS (Anti-lock Braking System) ... ..... .... 112 Accessories . .... ..... .... ..... .... ..... .... .... ..... .... 126 Accessory socket .... ..... .... ..... .... .... ..... .... .. 59 Air intake .... .... ..... .... ..... .... ..... .... .... ..... .... .. 95 Air recirculation system ... ..... .... .... ..... .... .. 93 Air vents . .... .... ..... .... ..... .... ..... .... .... ..... .... ..89 Airbags ... .... .... ..... .... ..... .... ..... .... .... ..... .... .. 54 Alarm . ..... ....
186 In dex Display instruments ..... .... ..... .... .... ..... .... .. 68 Display mode . ..... .... ..... .... ..... .... .... ..... .... .. 78 Door locks ... .... ..... .... ..... .... ..... .... .... ... 18, 155 Driving abroad Headlights .. ..... .... ..... .... ..... .... .... ..... .... .. 85 Driving hints ... ..... .... ..... .... ..... .... .... ..... .... 102 Environmental protection ... .... ..... .... ..... 154 EPS (Electric p ower steering) .. ..... ... 67, 102 Exhaust control indicator .... .
Index Height adjustment seat belts .... ..... .... ..... .... ..... .... .... ..... .... .. 50 Steering wheel . .... ..... .... ..... .... .... ..... .... .... 6 High pressure jet clea ner ..... .... .... ..... .... 155 Horn ... ..... .... .... ..... .... ..... .... ..... .... .... ..... .... .. 11 Hyd raulic brake sy stem .. ..... .... .... ..... .... 111 I Identification plate . ..... .... ..... .... .... .171, 172 Idling .. ..... .... .... ..... .... ..... .... ..... .... .... ..... .... 101 Ignition ..
188 In dex O il level ... .... .... ..... .... ..... .... ..... .... .... ..... .... 164 O il pressure .... ..... .... ..... .... ..... .... .... ..... .... .. 64 O perating temperature ... ..... .... .... ..... .... 103 O utside temperature ga uge .... .... ..... .... .. 72 O verrun ... .... .... ..... .... ..... .... ..... .... .... .103, 105 P Paintwork dama ge . ..... .... ..... .... .... ..... .... 154 Parking ... .... .... ..... .... ..... .... ..... .... .... ..... .... .. 15 Parking lights . ....
Index Tail lights .... .... ..... .... ..... .... ..... .... .... ..... .... .. 80 Bulb replacement ..... .... ..... .... .... ..... .... 150 Tailgate .. .... .... ..... .... ..... .... ..... .... .... ..... .. 2, 26 Technical d ata .... .... ..... .... ..... .... .... ..... .... 171 Telephone, see Mobile telephone .... .... .. 87 Tem perature regulation .. ..... .... .... ..... .... .. 90 Tem porary spare wheel .. ..... .... .... .118, 128 The first 600 miles (1000 km ) ... .... ..... ....
