Owner’s Manual Model Year 2012 Edition: February 2012 TS 1700-A-12 0-1 VAUXHALL Antara Owner’s Manual Model Year 2012 Edition: February 2012 TS 1700-A-12
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 33 Storage ........................................ 52 Instruments and controls ............. 70 Lighting ...................................... 102 Climate control ........................... 110 Driving and operating ................. 116 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving.
Introduction 5
6 In brief In brief Vehicle unlocking Seat adjustment Seat positioning Initial drive information Press button q to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, operate button above number plate. Radio remote control 3 19, Central locking system 3 20, Load compartment 3 22. Pull handle, slide seat, release handle. Seat position 3 34, Seat adjustment 3 35.
In brief Seat backrests Seat height Power seat adjustment Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on the seat backrest whilst adjusting it. Seat position 3 34, Seat adjustment 3 35. Lever pumping motion up = seat higher down = seat lower Operate switches. Seat position 3 34, Seat adjustment 3 35.
8 In brief Positioning = move front switch forwards/backwards Height of = move front part of front part of front switch seat upwards/ downwards Height of = move rear part of rear part of front switch seat upwards/ downwards Height of = move entire front entire seat switch upwards/ downwards Backrest = move upper part of rear switch forwards/backwards Seat position 3 34, Power seat adjustment 3 36. Head restraint adjustment Seat belt Press release button, adjust height and engage. Head restraints 3 33.
In brief Mirror adjustment 9 Exterior mirrors Steering wheel adjustment Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 26, Electric adjustment 3 26, Folding exterior mirrors 3 27, Heated exterior mirrors 3 27. Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked. Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released. Airbag system 3 43, Ignition positions 3 117.
10 In brief Instrument panel overview
In brief 1 2 3 Side air vents ..................... 114 Fixed air vents .................... 114 High beam .......................... 103 Headlight flash ................... 103 Turn and lane-change signals ................................ 105 Exit lighting ......................... 109 Parking lights ..................... 106 4 Cruise control ....................... 87 Remote control on steering wheel ...................... 70 5 6 7 Trip computer ....................... 97 Horn .......................
12 In brief Exterior lighting Turn light switch AUTO = Automatic light control: Headlights are switched on and off automatically. = Off (or deactivation of 7 automatic light control) = Sidelights 8 = Headlights 9 Press button > = Front fog lights r = Rear fog light Lighting 3 102. Headlight flash, high beam and low beam headlight flash high beam low beam = pull lever = push lever = pull lever back towards steering wheel Automatic light control 3 102, High beam 3 103, Headlight flash 3 103.
In brief Hazard warning flashers Horn Washer and wiper systems Windscreen wiper Operated with the ¨ button. Hazard warning flashers 3 104. 13 Press j. & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 71, Wiper blade replacement 3 151.
14 In brief Windscreen and headlight washer systems Rear window wiper and washer system Pull lever. Windscreen and headlight washer system 3 71, Washer fluid 3 147. Wiper on = push lever Wiper off = pull lever Wash = press and hold button Rear window wiper and washer system 3 73, Wiper blade replacement 3 151, Washer fluid 3 147. Climate control Heated rear window, heated exterior mirrors Heating is operated by pressing the Ü button. Heated rear window 3 30, Heated exterior mirrors 3 27.
In brief Demisting and defrosting the windows Air distribution to l. Cooling n and air recirculation 4 are switched on automatically to improve defrosting efficiency. Set temperature to highest level. Set fan speed to highest level. Switch on heated rear window Ü. Close centre air vents, open side air vents and direct them towards the door windows. Climate control system 3 110.
16 In brief Starting off Starting the engine Stop-start system ■ Turn key to position ACC ■ move the steering wheel slightly to release the steering wheel lock ■ manual transmission in neutral ■ operate clutch and brake pedals ■ automatic transmission in P or N ■ do not accelerate ■ diesel engines: turn key to ON for preheating and wait until control indicator ! extinguishes ■ turn key to START and release Starting the engine 3 117.
In brief Parking ■ Always apply the electrical parking brake. Pull switch m. For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice. ■ Switch off the engine and turn the ignition key to position LOCK, push key into ignition switch and remove. Turn the steering wheel until the steering wheel lock is felt to engage. For vehicles with automatic transmission, depress foot brake and shift into P before pushing key into ignition switch and removing.
18 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 22 Vehicle security ............................ 23 Exterior mirrors ............................ 26 Interior mirrors ............................. 28 Windows ...................................... 29 Roof .............................................
Keys, doors and windows Radio remote control Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system The radio remote control has a range of approx. 6 metres. This range can be affected by outside influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
20 Keys, doors and windows Key with fixed key section Open the unit with a small screwdriver in the notch on the cover. Replace the battery (battery type CR2032), paying attention to the installation position. Close the unit. Unlocking Locking Close doors, load compartment, fuel filler flap, bonnet, windows and sunroof. Central locking system Unlocks and locks doors, load compartment and fuel filler flap. Notice In the event of an accident of a certain severity, the vehicle unlocks automatically.
Keys, doors and windows Unlocking the tailgate 21 Locking Manually lock the driver's door by turning the key in the lock. Child locks Press button q. The tailgate is unlocked together with the doors. With the engine running, the tailgate will only unlock when the electrical parking brake is applied or automatic transmission is in position P. Central locking buttons Locks or unlocks all doors, the load compartment and fuel filler flap from the passenger compartment.
22 Keys, doors and windows Doors Load compartment Tailgate Opening Caution Closing Ensure there are no obstructions and that there is adequate clearance when opening the tailgate. 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases, which can not be seen or smelled, could enter the vehicle. This can cause unconsciousness and even death. Operate the button above the number plate and lift the tailgate.
Keys, doors and windows Fault Vehicle security 23 Activating Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside. To open the tailgate in the event of power interruption: Remove the interior trim cover from the central latch area, then push the lever using a suitable tool. The system deadlocks all the doors. All doors must be closed otherwise the system cannot be activated.
24 Keys, doors and windows ■ Siren power supply ■ Ignition Activation Ensure the doors, tailgate, fuel filler flap, bonnet, windows and sunroof are closed. Press button p on radio remote control or manually lock the driver's door.
Keys, doors and windows 3. Close doors. 4. Activate the anti-theft alarm system. Press button o again to cancel. Control indicator o extinguishes. Status LED Status during the first 30 seconds of anti-theft alarm system activation: LED = test, arming delay. illuminates LED flashes = doors, tailgate or quickly bonnet not completely closed, or system fault. Status after system is armed: LED flashes = system is slowly armed. LED flashes = system is quickly 3 times disarmed.
26 Keys, doors and windows Immobiliser The system is integrated into the ignition switch and checks whether the vehicle is allowed to start with the key being used. If the transponder in the key is recognized, the engine can be started. The electronic immobiliser is activated automatically after the key has been removed from the ignition switch. Control indicator d illuminates in the instrument cluster when the ignition is switched on, then extinguishes.
Keys, doors and windows 27 Folding Electric folding Heated For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. With ignition switch in positions ACC or ON, press button n and both exterior mirrors will fold in. Press button n again - both exterior mirrors return to their original position.
28 Keys, doors and windows Do not use sharp instruments or abrasive cleaners on the exterior mirrors and avoid scratching or damaging the heating elements. Interior mirrors Automatic anti-dazzle Manual anti-dazzle To reduce dazzle, adjust the lever on the underside of the mirror housing. Press button on mirror housing to turn function on; button illuminates and dazzle from following vehicles at night is automatically reduced. Press button again to turn function off.
Keys, doors and windows Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. payment must be attached in these areas. Otherwise data recording malfunctions may occur. 29 After switching off the ignition, window operation is disabled when the driver's door is opened. Manual windows The door windows can be opened or closed with the window winders.
30 Keys, doors and windows Additional switches are located in the front passenger's door and the rear doors. The rear windows do not open fully. Child safety system for rear windows Heated rear window Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again.
Keys, doors and windows Do not use sharp instruments or abrasive cleaners on the rear window and avoid scratching or damaging the heating elements. Sun visors Roof For incremental operation, briefly press the switch in the required direction. For automatic opening or closing, press and hold the switch. Sunroof 9 Warning Take care when operating the sunroof. Risk of injury, particularly to children. Keep a close watch on the movable parts when operating them.
32 Keys, doors and windows General hints Function standby The sunroof can be operated: ■ with ignition on, ■ within 10 minutes of switching ignition off, After switching off the ignition, sunroof operation is disabled when driver's door is opened.
Seats, restraints Seats, restraints Head restraints ............................ 33 Front seats ................................... 34 Rear seats ................................... 38 Seat belts ..................................... 39 Airbag system .............................. 43 Child restraints ............................. 47 Head restraints 33 Height adjustment Position 9 Warning Only drive with the head restraint set to the proper position.
34 Seats, restraints Stow head restraints securely in load compartment. Active head restraints on front seats In the event of a rear-end impact, the active head restraints automatically tilt forwards. The head is more effectively supported by the head restraint and the risk of whiplash injury is reduced. Do not attach objects or components that are not approved for your vehicle to the head restraints.
Seats, restraints Seat adjustment 9 Danger Pull handle, slide seat, release handle. Seat height Seat backrests Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on the seat backrest whilst adjusting it.
36 Seats, restraints Lumbar support Seat folding Folding the backrest forwards is possible only when the backrest is in an upright position. Do not operate lever to adjust lumbar support with backrest tilted forward. Power seat adjustment 9 Warning Adjust lumbar support to suit personal requirements using the lever. To increase or decrease lumbar support, move lever forwards or backwards. Push head restraint all the way down. Slide seat as far back as it will go.
Seats, restraints 37 Seat backrests Heating Move upper part of rear switch forwards/backwards. The seat backrest must not be tilted back too far (recommended maximum tilting angle approx. 25°). Adjust heating to the desired setting by pressing the ß button for the respective seat one or more times with the ignition switch set to ACC or ON. The control indicator in the button indicates the setting. To deactivate heating, set the heating level to its lowest setting and press the ß button.
38 Seats, restraints If temperature continues to rise, turn seat heating off and seek the assistance of a workshop. Rear seats 9 Warning Seat backrests Never adjust seats while driving as they could move uncontrollably. Seat folding To adjust seat backrests, lift release lever on top of backrest and move backrest forwards/backwards to desired position. Do not lean on the backrest whilst adjusting it. When folding the backrests, ensure the seat belts are unbuckled.
Seats, restraints Push head restraints all the way down, lift backrest release lever and fold backrest forwards and down onto seat cushion. Do not allow passengers to sit on a folded backrest, or place any unrestrained loads on it. To move backrest to its original position, lift and push the backrest into place and ensure the backrest engages. Safety net 3 66. Armrest Fold armrest down. The armrest contains cupholders and a storage box.
40 Seats, restraints Seat belts are designed to be used by only one person at a time. They are not suitable for people smaller than 150 cm. Child restraint system 3 47. Periodically check all parts of the belt system for damage and proper functionality. Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop. Notice Make sure that the belts are not damaged by shoes or sharp-edged objects or are trapped.
Seats, restraints 41 Height adjustment Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. 1. Squeeze release buttons together. 2. Slide adjuster up or down. 3. Ensure adjuster latches into position. Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm.
42 Seats, restraints Removing To release belt, press red button on belt buckle. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen. Front passenger seat belt reminder When the engine is running, control indicator k flashes then illuminates if the passenger seat is occupied and the seat belt is not engaged.
Seats, restraints Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Notice The airbag systems and belt pretensioner control electronics are located in the centre console area.
44 Seats, restraints Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The inflated airbags cushion the impact, thereby considerably reducing the risk of injury to the upper body and head of the front seat occupants. 9 Warning Optimum protection is only provided when the seat is in the proper position 3 34. Keep the area in which the airbag inflates clear of obstructions.
Seats, restraints Curtain airbag system The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars. The curtain airbag system is triggered in the event of a side-on impact of a certain severity. The ignition needs to be switched on. The curtain airbag system is triggered with the side airbag system and functions independently of the front airbag system.
46 Seats, restraints Use the ignition key to choose the position: = front passenger airbag * OFF systems are deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously on the passenger side of the instrument panel. A child restraint system can be installed in accordance with the chart Child restraint installation locations 3 48. No adult person is allowed to occupy the front passenger seat. V = front passenger airbag ON systems are active.
Seats, restraints Child restraints Child restraint systems We recommend the Vauxhall child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats.
48 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system On front passenger seat Weight and age class activated airbag deactivated airbag On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months X U1 U, < X Group 0+: up to 13 kg or approx. 2 years X U1 U, < X Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U, < X Group II: 15 to 25 kg or approx.
Seats, restraints 49 Permissible options for fitting an ISOFIX child restraint system On front passenger seat On rear On rear outboard seats centre seat Weight and age class Size class Fixture Group 0: up to 10 kg or approx. 10 months E ISO/R1 X IL X Group 0+: up to 13 kg or approx. 2 years E ISO/R1 X IL X D ISO/R2 X IL X C ISO/R3 X IL X Group I: 9 to 18 kg or approx.
50 Seats, restraints ISOFIX size class and seat device A - ISO/F3 B - ISO/F2 B1 - ISO/F2X C - ISO/R3 D - ISO/R2 E - ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Permitted installation positions for specific vehicle ISOFIX child restraint systems are marked in the table by IL. No more than two ISOFIX child restraint systems can be installed on the rear seats at the same time, though not on the rear centre seat. ISOFIX mounting brackets are indicated by a label on the backrest.
52 Storage Storage Storage compartments Glovebox Storage compartments ................ 52 Load compartment ....................... 63 Roof rack system ......................... 68 Loading information ..................... 68 Cupholders Cupholders are located in the front of the centre console. The cupholder is flexible, allowing different size drink containers to be stored. Additional cupholders are located in the centre rear seat armrest. Fold down the armrest to access the cupholder.
Storage Located in the front passenger foot well. Sunglasses storage Card holder Located above the coin storage compartment. A card can be retained in the slot for convenient use. Underseat storage Front passenger seat undertray Coin storage Pull handle to open. Push door firmly to close. 53 To open: push the rear part of the cover. To close: pull up cover and push it until it latches into place. Do not use for storing heavy objects. Pull up on front of tray then pull it forwards.
54 Storage Armrest storage Rear carrier system Console box in front armrest There must not be any objects on the bicycles that could become loose during transportation. Caution Do not attach bicycles with carbon pedal cranks to bicycle carriers. The bicycles might get damaged. Extending Open the tailgate. To open: pull up lever and lift the lid. To close: lower lid and push it down until it latches into position.
Storage Completely pull out the rear carrier system until it engages. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again. 55 Pull up license plate holder and fully insert the holder supports into the retainers. Install the tail lamps 9 Warning Raise release lever. The system disengages and travels quickly out of the bumper. It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged.
56 Storage Push the clamping lever and push the bulb holder into the retainer until it hits the stop. Perform this procedure for both tail lamps. Open out the bulb holder on the back of the tail lamp completely. Check the cable and lamp position to make sure these are correctly installed and are securely located. Lock the rear carrier system Swivel the left clamping lever (1) back first, followed by the right clamping lever (2) until they stop.
Storage Adapting the rear carrier system to a bicycle Unfold pedal crank recesses Fold one or both pedal crank recesses upwards until the diagonal support engages. 57 Remove the pedal crank mounts from the pedal crank recesses. With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank. If the bicycle has straight pedal cranks, unscrew the pedal crank unit completely (position 5).
58 Storage Press the release lever and withdraw the wheel recesses. If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1). Push the release lever on the strap retainer and remove the strap retainer. Prepare the bicycle for attachment Notice The maximum width for the pedal crank is 38,3 mm and the maximum depth is 14,4 mm. Rotate the left pedal (without a chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal.
Storage Attaching a bicycle to the rear carrier system Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. Caution Make sure that the pedal does not touch the surface of the rear end carrier. Otherwise the bicycle chainset might be damaged during transport. 59 Attach the pedal crank by rotating the attachment screw on the pedal crank mount.
60 Storage saved for each bicycle. Correct presetting will facilitate refitting of the bicycle. Align the bicycle in the longitudinal direction of the vehicle: Slightly loosen the pedal mount. Place the bicycle upright using the rotary lever on the pedal crank recess. If the two bicycles obstruct one another, the relative positions of the bicycles can be adapted by adjusting the wheel recesses and the rotary lever on the pedal crank recess until the bicycles no longer touch one another.
Storage Removing a bicycle from the rear carrier system 61 Retracting the rear carrier system Insert the strap retainer and pull tightly downwards as far as possible. Undo strap retainers on both bicycle tyres. Hold on to the bicycle, loosen the attachment screw for the pedal bearing mount, then lift the pedal bearing mount to remove it. Push the pedal crank mounts into the pedal crank recess as shown in the illustration.
62 Storage Press release lever and slide in wheel recesses all the way as far as they will go. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down. 9 Warning Risk of pinching. Push the clamping lever down and pull both lamp supports out of the recesses. Swivel first the right clamping lever (1) forwards, followed by the left clamping lever (2), until they can be engaged in their respective recesses. Fold in the bulb holders on the backs of the tail lamps.
Storage Raise the release lever up and push the system into the bumper until it engages. Release lever must return to original position. 63 Load compartment Storage compartments in the load compartment 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop. Pull up license plate holder and fold down into horizontal position. Located on both sides of the load compartment floor. Load compartment cover Do not place any objects on the cover. Open the tailgate.
64 Storage Closing the cover Removing the cover Rear floor storage cover Pull load compartment cover towards rear of vehicle using handle and insert retainers into brackets on either side of load compartment. Open load compartment cover. Pull socket on either side of cover towards centre of vehicle, lift and remove cover from the side guides. Fit in reverse order. To access the rear floor storage compartment, push both levers on the floor cover towards the handle and pull up the cover by the handle.
Storage Lashing eyes 65 Cargo management system The FlexOrganizer is a flexible system for dividing the load compartment or securing loads. Hang the hook to the upper part of the tailgate opening. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. Jack and vehicle tools 3 165. Tyre repair kit 3 171. Temporary spare wheel 3 177.
66 Storage Variable partition net To remove, press the net rod together and remove from the adapters. Fold open the adapter handle plate, disengage from lower groove and then from upper groove. Hooks and mesh pocket Safety net The safety net can be mounted behind the rear seats or, if the rear seat backrests are folded down, in front of the rear seats. Passengers must not be transported behind the safety net.
Storage When fitting in front of the rear seats, push head restraints of the rear seats down and fold down rear seat backrests 3 38. Open aperture covers on the roof frame and insert top corners of safety net into large apertures in roof frame and secure by sliding them into the smaller apertures. 9 Warning Do not stack loads higher than the upper end of the safety net. Avoid applying excessive force to the safety net or hanging heavy items from it.
68 Storage Roof rack system Loading information Roof rack ■ Heavy objects in the load compartment should be evenly distributed and placed as far forward as possible. Ensure the backrests are securely engaged. If objects can be stacked, the heavier objects should be placed at the bottom. With rear seats in the folded position, or with safety net installed behind rear seats, objects must not be stacked higher than the seat backrests. ■ Secure objects with lashing straps attached to lashing eyes 3 65.
Storage vehicle weight (see identification plate 3 189) and the EC kerb weight. To calculate the EC kerb weight, enter the data for your vehicle in the Weights table at the front of this manual. The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). Optional equipment and accessories increase the kerb weight.
70 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 70 Warning lights, gauges and indicators ..................................... 77 Information displays ..................... 88 Vehicle messages ........................ 96 Trip computer ............................... 97 Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked.
Instruments and controls Horn Windscreen wiper/washer 71 Adjustable wiper interval Windscreen wiper Press j. & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Do not use if the windscreen is frozen. Switch off in car washes. To set the wiping interval to a value between 1 and 10 seconds: ■ Switch on ignition. ■ Push lever down from position §.
72 Instruments and controls In this mode, wiping frequency is also affected by vehicle speed. As vehicle speed increases, wiping will become more frequent. Automatic wiping with rain sensor $ = automatic wiping with rain sensor The rain sensor detects the amount of water on the windscreen and automatically regulates the frequency of the windscreen wiper. The wiper operates for one cycle to check the system when the key is turned to ignition switch position ACC.
Instruments and controls Control indicator G illuminates in the instrument cluster when the washer fluid level is low. Wiper activated lighting With light switch in the AUTO position, when the windscreen wiper is operated for 8 cycles or more the exterior lights illuminate automatically. Rear window wiper/washer Move lever to activate the rear window wiper: Push lever = wiper on Pull lever = wiper off To activate rear window washer system, press and hold button on end of lever.
74 Instruments and controls Automatic time synchronisation 9 Warning Board-Info-Display The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock Graphic-Info-Display, Colour-Info-Display 3 91. Date and time are shown in the Info-Display. Board-Info-Display 3 88. The RDS (Radio Data System) signal of most VHF transmitters automatically sets the time, identified by } in the display. Some RDS transmitters do not send a correct time signal.
Instruments and controls Deactivate (Clock Sync.Off) or activate (Clock Sync.On) automatic time synchronisation with the arrow buttons on the Infotainment system. To set date and time manually, select the menu item for time and date setting from the Settings menu and make the desired setting. The value ready for modification is marked with arrows. Use the arrow buttons to make the required setting. The setting is saved when the menu item is exited.
76 Instruments and controls A 12 Volt power outlet is located in the rear centre console and on the righthand side of the load compartment. Pull the cap out to use the accessory socket, and replace the cap when not in use. Do not exceed the maximum power consumption of 120 watts. Operational with ignition switch in positions ACC or ON. Use of accessory sockets while the engine is not running will discharge the battery.
Instruments and controls To replace battery: remove screw on ashtray lid and replace with CR 2032 (or equivalent) battery. Warning lights, gauges and indicators 77 Odometer Speedometer The bottom line displays the recorded distance. Indicates vehicle speed. Trip odometer The top line displays the recorded distance since the last reset. There are two independent trip odometers. Press the trip odometer button once to toggle between Trip A and Trip B.
78 Instruments and controls Tachometer Fuel gauge Transmission display Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Displays the fuel level in the tank. Control indicator Y illuminates if the level in the tank is low. Refuel immediately 3 137. Never run the tank dry. Erratic fuel supply can cause catalytic converter to overheat 3 121. Diesel engines: if the tank has been run dry, bleed the fuel system 3 151.
Instruments and controls When the ignition is switched on, most control indicators will illuminate briefly as a functionality test. The control indicator colours mean: red = danger, important reminder yellow = warning, information, fault green = confirmation of activation blue = confirmation of activation Control indicators on the instrument panel k illuminates red. Front passenger seat belt reminder 3 40. * illuminates yellow. The front passenger airbag is deactivated 3 45.
80 Instruments and controls Control indicators in the instrument cluster
Instruments and controls Turn signal O illuminates or flashes green. The relevant control indicator flashes when the turn signal is switched on 3 105. Rapid flashing: failure of a turn signal bulb or the associated fuse or failure of a turn signal light on trailer. Both control indicators flash when the hazard warning flashers are active 3 104. Bulb replacement 3 151, Fuses 3 157. Turn signals 3 105. Seat belt reminder X illuminates or flashes red.
82 Instruments and controls Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. If it does not illuminate, seek the assistance of a workshop. Can illuminate briefly when driving; this is normal and does not indicate a system fault. Illuminates when the engine is running Fault in the emission control system. The permitted emission limits may be exceeded. Fuel economy and vehicle driveability may be impaired. Seek the assistance of a workshop immediately.
Instruments and controls When the engine is started, m illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates Electrical parking brake is applied 3 129. Flashes Electrical parking brake is not fully applied or released. Switch on ignition, depress brake pedal and attempt to reset the system by first releasing and then re-applying the electrical parking brake. If m remains flashing, do not drive and seek the assistance of a workshop.
84 Instruments and controls Green Illuminates when system is ready for operation. Flashes during driving when system is in operation, after pressing the u button. Yellow Flashes to indicate system is not ready for conditions to operate. Illuminates to indicate there is a fault in the system. If it flashes or illuminates during driving, friction material needs to cool down: drive the vehicle without braking as much as possible. Descent control system 3 132. Power steering 2 illuminates yellow.
Instruments and controls Engine coolant temperature W illuminates red. When the engine is started, W illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates when the engine is running Stop vehicle and switch off engine. Caution Coolant temperature too high. Check coolant level 3 146. If there is sufficient coolant, seek the assistance of a workshop. Preheating ! illuminates yellow. Preheating is activated. Only activates when outside temperature is low.
86 Instruments and controls 9 Warning When the engine is off, considerably more force is needed to brake and steer. Do not remove key until vehicle is stationary, otherwise the steering wheel lock could engage unexpectedly. Check oil level before seeking the assistance of a workshop 3 145. Low engine oil level S illuminates yellow. When the ignition is switched on, S illuminates briefly. If it does not illuminate, seek the assistance of a workshop.
Instruments and controls Residual water in the diesel fuel filter must be drained 3 150. Seek the assistance of a workshop as soon as possible. Immobiliser d illuminates red. When the engine is started, d illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates to indicate a fault in the immobiliser system. The engine cannot be started. Electronic immobiliser 3 26. Reduced engine power # illuminates yellow. Illuminates in conjunction g, the vehicle needs a service.
88 Instruments and controls control indicator W flashes, accompanied by a warning chime, to warn the driver to reduce speed as appropriate. Trailer indicator g illuminates green. Illuminates when a trailer is connected to the vehicle 3 139. Anti-theft alarm system a illuminates yellow. Illuminates when alarm system monitoring of the passenger compartment and vehicle inclination has been switched off with button a in the roof lining. Anti-theft alarm system 3 23.
Instruments and controls The Info-Display is located in the instrument panel above the Infotainment system. An F in the display indicates a fault. Have the cause of the fault remedied by a workshop. Trip computer, Board-Info-Display 3 97. 89 Select using the Infotainment system buttons Select using the left adjuster wheel on the steering wheel In the Settings menu, use the OK button to call up the required function. Use the arrow buttons to change settings.
90 Instruments and controls System settings ■ ■ ■ ■ ■ ■ ■ Time, setting minutes Date, setting day Date, setting month Date, setting year Ignition logic Language selection Setting units of measure Automatic time synchronisation Press the Settings button of the Infotainment system. Menu item Audio then opens. Call up System with the left arrow button and select with the OK button. The first function of the System menu is highlighted. Some of the functions appear on the display in an abbreviated form.
Instruments and controls The value ready for modification is marked with arrows. Use the arrow buttons to make the required setting. The setting is saved when the menu item is exited. 91 Setting units of measure Ignition logic See Infotainment system instruction manual. Language selection Select the required unit of measurement with the arrow buttons. Graphic-Info-Display, Colour-Info-Display The display language for some functions can be selected. Select the required language with the arrow buttons.
92 Instruments and controls The type of information and how it is displayed depends on the equipment of the vehicle and the settings of the trip computer and Infotainment system. Some information appears on the display in an abbreviated form. An F in the display indicates a fault. Have the cause of the fault remedied by a workshop. Trip computer, Graphic-Info-Display, Colour-Info-Display 3 99. wheel. If there are several warning messages, acknowledge them one at a time. Check control 3 96.
Instruments and controls Select using the left adjuster wheel on the steering wheel Turn the adjuster wheel to call up the required function. Press the adjuster wheel to select marked items and confirm commands. Press to operate the stop watch or restart measurement and calculation. Trip computer 3 99. 93 Function areas System settings For each function area there is a main page (Main), which is selected at the top edge of the display: ■ Audio, ■ Navigation, ■ Telephone, ■ Trip computer.
94 Instruments and controls ■ Contrast ■ Day / Night ■ Ignition logic Setting date and time With the navigation system, date and time are set automatically upon receipt of a GPS satellite signal. If the displayed time does not match local time, it can be corrected manually or automatically by receiving an RDS time signal. Some RDS transmitters do not send a correct time signal. In such cases, switch off automatic time synchronisation and set the time manually.
Instruments and controls Setting units of measure Select the desired language. Selections are indicated by a 6 in front of the menu item. In systems with voice output, when the language setting of the display is changed, the system will ask whether the announcement language should also be changed – see Infotainment system instruction manual. Select menu item Units from the Settings menu. The available units are displayed. Select the desired unit. Selections are indicated by a o in front of the menu item.
96 Instruments and controls Always day design; black or coloured text on a light background. Always night design; white or coloured text on a dark background. Selections are indicated by a o in front of the menu item. Ignition logic See Infotainment system instruction manual. Vehicle messages Warning chimes When starting the engine or whilst driving ■ If seat belt is not fastened. ■ When operating the turn and lanechange signals.
Instruments and controls Reduce speed and check tyre pressure at the next opportunity. Tyre pressure monitoring system 3 168. Check tyre pressures 3 168, 3 198. If there is a considerable loss of pressure, a corresponding message appears indicating the relevant tyre. Steer out of the flow of traffic as quickly as possible without endangering other vehicles. Stop and check the tyres. Mount the spare wheel 3 174, 3 177. Tyre pressure monitoring system 3 168.
98 Instruments and controls Average consumption Display of average consumption. The measurement can be reset at any time. Effective consumption Display of the amount of fuel consumed. The measurement can be reset at any time. Average speed Display of average speed. The measurement can be reset at any time. Stoppages in the journey with the ignition off are not included in the calculations. Distance travelled Display of distance travelled. The measurement can be reset at any time.
Instruments and controls Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. Trip computer in GraphicInfo-Display or ColourInfo-Display page provides information on range, average consumption and instantaneous consumption. To display other trip computer data, press the BC button on the Infotainment system and select the trip computer menu in the display.
100 Instruments and controls Instantaneous consumption Display of the instantaneous consumption. Display changes depending on speed: Display in gal/h = below 8 mph Display in miles/gal = above 8 mph Average consumption Display of average consumption. The measurement can be reset at any time. Resetting trip computer information Distance travelled Display of distance travelled. The measurement can be reset at any time. To reset all information of a trip computer, select menu item All values.
Instruments and controls Stop watch Travel Time: Measurement of the time from manual activation via Start to manual deactivation via Reset. Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost. Select menu item Timer from the Board Computer menu. The Timer menu is displayed. To start, select menu item Start. To reset, select menu item Reset.
102 Lighting Lighting Exterior lighting Light switch Exterior lighting .......................... 102 Interior lighting ........................... 107 Lighting features ........................ 109 Tail lights Tail lights illuminate together with the headlights and sidelights. Automatic light control Turn light switch: AUTO = Automatic light control: Headlights are switched on and off automatically depending on external lighting conditions. = Off (or deactivation of 7 automatic light control).
Lighting To ensure automatic light control functions properly, do not cover the light sensor on top of the instrument panel. High beam 103 Headlight range adjustment Manual headlight range adjustment Daytime running lights Daytime running lights increase visibility of the vehicle during daylight. The lights operate automatically when the ignition is switched on. Driving abroad 3 104.
104 Lighting Vehicles without automatic level control system Turn thumb wheel to required position: 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden 3 = driver's seat occupied and load compartment laden Vehicles with automatic level control system Turn thumb wheel to required position: 0 = front seats occupied 1 = all seats occupied 1 = all seats occupied and load compartment laden 2 = driver's seat occupied and load compartment laden Automatic level contro
Lighting Turn and lane-change signals For three flashes, e.g. when changing lanes, press the lever until resistance is felt and then release. Move the lever to the resistance point and hold for longer indication. The volume of the turn signal audible warning is dependent upon vehicle speed. Switch the turn signal off manually by moving the lever to its original position. Control indicators O 3 81.
106 Lighting Rear fog lights The vehicle rear fog light is deactivated when towing. Parking lights Confirmed by a signal tone and the corresponding turn signal control indicator. To deactivate, switch on the ignition or move the turn signal lever in the opposite direction. Reversing lights The reversing lights come on when the ignition is on and reverse gear is selected. Centre high-mounted brake light Operated with the r button.
Lighting Interior lighting Instrument panel illumination control automatically for 30 seconds until ignition switch is turned to position ACC. Display mode 3 91. Interior lights Front courtesy light The instrument panel illuminates when the ignition is switched on. Brightness can be adjusted when the exterior lights are on: Turn thumb wheel to the right or left until the desired brightness is obtained.
108 Lighting Switch off immediately by pressing button K in the roof lining. Ashtray illumination Reading lights Rear reading lights Front reading lights The portable front ashtray, located in the front drink holder, illuminates depending on outside light conditions. Glovebox illumination Illuminates when the glovebox is opened. Load compartment lighting Operated with the L and M buttons. Avoid using front reading lights while driving in the dark, as they can reduce driver visibility.
Lighting Lighting features Switching on Entry lighting Depending upon outside light conditions, when unlocking the vehicle with the remote control the hazard warning lights flash twice and the exterior and interior lights illuminate for 20 seconds. This function facilitates locating the vehicle when it is dark. The low beam and reversing lights illuminate for 30 seconds after the driver exits the vehicle and closes the door.
110 Climate control Climate control Climate control systems ............. 110 Air vents ..................................... 114 Maintenance .............................. 115 Climate control systems Heating and ventilation system Temperature red = warm blue = cold Heating will not be fully effective until the engine has reached normal operating temperature. Air distribution Controls for: ■ Temperature ■ Air distribution ■ Fan speed Heated rear window Ü 3 30. Heated seats 3 37.
Climate control Air conditioning system In addition to the heating and ventilation system, the air conditioning system has: n = cooling 4 = air recirculation Ü = demisting and defrosting Cooling n Operated with the n button and is functional only when the engine and fan are running. freezing point. Therefore condensation may form and drip from under the vehicle. If no cooling or drying is required, switch the cooling system off to save fuel.
112 Climate control Electronic climate control system Do not cover the interior temperature sensor (located below the fan switch) or the sunlight sensor (located in front of the windscreen defroster vents) as this could cause the system to malfunction. Automatic mode AUTO Basic setting for maximum comfort: ■ Set the air distribution switch to l or J. ■ Set temperature control to warmest level. ■ Set fan to highest level. ■ Close centre air vents.
Climate control Recommended comfort setting is 22 °C. Intermediate settings are possible. To deactivate automatic mode, turn fan to position off x. All air vents are actuated automatically in automatic mode. The air vents should therefore always be open. Operated with the t button. The automatic air recirculation system is only operational if the engine is running.
114 Climate control Air vents The area underneath the front seats must be kept clear, to allow air flow to the rear passenger foot well. Adjustable air vents Direct the flow of air by tilting and swivelling the slats. To open and close the vents, turn the horizontal adjuster wheel to the left or right. Open air vents when air distribution switch is set to M or L. The air supply is increased by switching on the fan.
Climate control Maintenance Air intake Active carbon filter In addition to the particle filter the active carbon filter reduces odours. Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a week, irrespective of the weather and time of year. Operation with cooling is not possible when outside temperature is too low.
116 Driving and operating Driving and operating Driving hints ............................... 116 Starting and operating ............... 116 Engine exhaust .......................... 120 Automatic transmission .............. 122 Manual transmission .................. 126 Drive systems ............................ 126 Brakes ........................................ 129 Ride control systems ................. 131 Cruise control ............................. 133 Object detection systems ........... 135 Fuel .
Driving and operating 117 Ignition switch positions Starting the engine Before restarting or to switch off the engine, turn key back to LOCK. Start attempts should not last longer than 15 seconds. If engine does not start, wait 10 seconds before repeating starting procedure. The increased engine speed automatically returns to normal idling speed as the engine temperature rises. Drive at a moderate speed, especially in cold weather, until normal engine operating temperatures have been reached.
118 Driving and operating Ensure the engine oil is of the correct viscosity, the correct fuel is used, vehicle services are performed regularly and the battery is sufficiently charged. Deactivation Stop-start system The stop-start system helps to save fuel and to reduce the exhaust emissions. When conditions allow, it switches off the engine as soon as the vehicle is at a low speed or at a standstill, e.g. at a traffic light or in a traffic jam.
Driving and operating Conditions for an Autostop The stop-start system checks if each of the following conditions is fulfilled. Otherwise an Autostop will be inhibited.
120 Driving and operating For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice. ■ Switch off the engine and turn the ignition key to position LOCK, push key into ignition switch and remove. Turn the steering wheel until the steering wheel lock is felt to engage. For vehicles with automatic transmission, depress foot brake and shift into P before pushing key into ignition switch and removing.
Driving and operating The filter is cleaned by periodically burning off the soot particles at high temperature. This process takes place automatically under set driving conditions and may take up to 15 minutes. Fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal. If cleaning of the filter is required and previous driving conditions did not enable automatic cleaning, it will be indicated by control indicator % 3 85.
122 Driving and operating Caution Fuel grades other than those listed on pages 3 136, 3 193 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
Driving and operating The selector lever is locked in position P and N and can only be moved when the ignition is on and the foot brake is applied. To engage P or R, push the release button. Never shift to P or R while the vehicle is moving. The engine can only be started with lever in position P or N. Depress foot brake or apply electrical parking brake before starting. Do not accelerate while engaging a gear. Never depress the accelerator pedal and brake pedal at the same time.
124 Driving and operating transmission will automatically shift to a lower gear, even in manual mode, to prevent the engine from stalling. If a higher gear is selected when vehicle speed is too low, or a lower gear when vehicle speed is too high, the shift is not executed. In manual mode, no automatic shifting to a higher gear takes place at high engine revolutions. Gears can be skipped by moving the selector lever repeatedly at short intervals. After stopping, 1st gear is automatically selected.
Driving and operating Deactivation Fuel economy mode is switched off by pressing button s again; control indicator s extinguishes in the instrument cluster. Fault In the event of a fault in the automatic transmission, control indicator Z illuminates in the instrument cluster 3 81. Automatic shifting may be much harsher than normal or, in the case of a serious fault, cancelled altogether. Have the cause of the fault remedied by a workshop.
126 Driving and operating Manual transmission Caution It is inadvisable to drive with hand resting on the selector lever. Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection. Do not grind the clutch unnecessarily. When operating, depress the clutch pedal completely. Do not use the pedal as a foot rest.
Driving and operating Ensure tyres (including the spare) are inflated to the correct pressure 3 198 and are suitable for the prevailing road conditions. For optimum system performance, the vehicle's tyres should not have varying degrees of wear. If control indicator B flashes in the instrument cluster during driving, Allwheel drive is temporarily disabled. If B flashes continuously, there is a fault in the system; seek the assistance of a workshop. All-wheel drive control indicator B 3 83.
128 Driving and operating operations for wading , involving checks for water contamination, at the earliest opportunity. Service checks after wading Check for the ingress of water into the following: ■ Brake fluid reservoir ■ Air cleaner element ■ Engine ■ Transmission ■ Axles ■ Interior of vehicle Renew any lubricating oil or hydraulic fluid that has a milky appearance, indicating contamination with water. Cleaning Clean the vehicle thoroughly and as soon as possible after driving offroad.
Driving and operating Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly. Considerably more force is needed for this. The braking distance is extended. Seek the assistance of a workshop before continuing your journey.
130 Driving and operating Applying when vehicle is stationary Pull switch m, the electrical parking brake operates automatically with adequate force. For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice. The electrical parking brake can always be activated, even if the ignition is off. Do not operate electrical parking brake system too often without engine running as this will discharge the battery. Before leaving the vehicle, check the electrical parking brake status.
Driving and operating movement. Seek the assistance of a workshop to have the cause of the fault remedied. Ride control systems Brake assist Electronic Stability Control (ESC) improves driving stability when necessary, regardless of the type of road surface or tyre grip. It also prevents the drive wheels from spinning. As soon as the vehicle starts to swerve (understeer/oversteer), engine output is reduced and the wheels are braked individually.
132 Driving and operating Switch off ESC function, to allow engine rpm to increase, by pressing button t briefly. Control indicator t illuminates in the instrument cluster. ESC is reactivated by pressing button t again. The control indicator extinguishes. Control indicator t 3 84. Hydraulic brake assist When the ESC function comes into action and recognises any emergency situation requiring hard braking, it automatically delivers increased braking pressure to the wheels.
Driving and operating Deactivation Press button u again. The green control indicator u extinguishes. Depressing the foot brake or accelerator will also cause the system to be deactivated. Fault The yellow control indicator u flashes to indicate that the system is not ready for conditions to operate, due to the high temperature (approx. 350 - 400 °C) of friction material, through severe or repeated braking. It will extinguish when the temperature drops below 350 °C.
134 Driving and operating With automatic transmission, only activate cruise control in automatic mode. Control indicator m 3 87. Alternatively accelerate to the desired speed and store by pressing the SET button. Activation With cruise control active, press and hold the - SET button or tap the SET button repeatedly: speed decreases continuously or in small increments. Press the e button; control indicator m illuminates yellow in the instrument cluster.
Driving and operating Object detection systems Control indicator r 3 84. Activation Parking assist The parking assist system makes parking easier by measuring the distance between the vehicle and obstacles to the front and rear, and giving acoustic signals. It is the driver, however, who bears full responsibility for the parking manoeuvre. The system consists of four ultrasonic parking sensors in both the front and rear bumpers. 135 When the distance is less than 30 cm, the signal is continuous.
136 Driving and operating If the acoustic signal sounds 3 times continuously when there are no obstacles near the front or rear bumper, there is a fault in the system. Have the cause of the fault remedied by a workshop. Important hints for using the parking assist system 9 Warning Under certain circumstances, various reflective surfaces on objects or clothing as well as external noise sources may cause the system to fail to detect obstacles.
Driving and operating Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage. Fuel for ethanol adapted engines (E85) If access to E85 is limited then fuel with a different proportion of ethanol or normal RON 95 can be used for refuelling. The engine's control management system is adjusted automatically according to the amount of ethanol in the fuel. E85 fuel must fulfil the CWA 15293 or SS 155480 standard.
138 Driving and operating Caution 9 Danger Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this remedied immediately by a workshop. Caution In case of misfuelling, do not switch on ignition. Fuel filler flap is located at left rear side of vehicle. The fuel filler flap can only be opened if the vehicle is unlocked 3 20. Release the fuel filler flap by pushing the flap. Wipe off any overflowing fuel immediately.
Driving and operating General information The official fuel consumption and specific CO2 emission figures quoted relate to the EU base model with standard equipment. Fuel consumption data and CO2 emission data are determined according to regulation R (EC) No. 715/2007 (in the version respectively applicable), taking into consideration the vehicle weight in running order, as specified by the regulation.
140 Driving and operating When driving downhill, drive in the same gear as if driving uphill and drive at a similar speed. Adjust tyre pressure to the value specified for full load 3 198. Trailer towing Trailer loads The permissible trailer loads are vehicle-dependent and enginedependent maximum values which must not be exceeded. The actual trailer load is the difference between the actual gross weight of the trailer and the actual coupling socket load with the trailer coupled.
Driving and operating Towing equipment Caution Remove sealing plug from the hole for the coupling ball bar and stow it in the load compartment. 141 Inserting the coupling ball bar When operating without a trailer, remove the coupling ball bar. Towing equipment with detachable coupling ball bar The coupling ball bar is kept in a bag, fastened with a strap and is stowed below the floor cover in the load compartment. Fitting the coupling ball bar Confirm that the colour marking on the lever is red.
142 Driving and operating 9 Warning Towing a trailer is permitted only when the coupling ball bar is fitted correctly. If the coupling ball bar cannot be properly attached, seek the assistance of a workshop. Lock coupling ball bar by turning the supplied key in the lock cylinder of the coupling ball bar. Remove key. Check that the coupling ball bar is correctly attached: ■ Green marking must be visible on lever. ■ Coupling ball bar must be seated firmly in coupling housing.
Vehicle care Vehicle care General Information ................... 143 Vehicle checks ........................... 144 Bulb replacement ....................... 151 Electrical system ........................ 157 Vehicle tools .............................. 165 Wheels and tyres ....................... 167 Jump starting ............................. 178 Towing ....................................... 180 Appearance care .......................
144 Vehicle care Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir. ■ Check the engine oil level. ■ Check the coolant level. ■ Fit the number plate if necessary. Seek the assistance of a workshop for further advice.
Vehicle care 145 Engine oil Locate the safety catch, found slightly left of centre on the underside of the bonnet, push the catch upwards and lift the bonnet gently. The bonnet is held open automatically. Air intake 3 115. Closing Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. Check the engine oil level manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used. Recommended fluids and lubricants 3 186.
146 Vehicle care Control indicators for engine oil pressure I 3 85, low engine oil S 3 86 and engine oil life C 3 86. Once the engine oil has been changed, the engine oil life monitor needs to be reset. Seek the assistance of a workshop. Engine coolant The coolant provides freeze protection down to approx. -28 °C. We recommend the use of the same grade of engine oil that was used at the last oil change. The engine oil level must not exceed the MAX mark on the dipstick.
Vehicle care the coolant concentration checked and have the cause of the coolant loss remedied by a workshop. Engine coolant temperature control indicator W 3 85. Washer fluid Power steering fluid 147 Do not spray washer fluid onto windscreen in freezing weather, to avoid ice forming and impairing vision. In cold weather, do not fill the washer fluid reservoir more than three quarters full, to allow enough room for expansion if the fluid freezes, and to prevent damage to the reservoir.
148 Vehicle care Clutch fluid 9 Warning Clutch fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces. The brake fluid level must be between the MIN and MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop. Only use high-performance brake fluid approved for the vehicle. Brake fluid 3 186.
Vehicle care Retrofitted electrical or electronic accessories can place an additional load on the battery or discharge the battery. Seek the assistance of a workshop regarding technical possibilities, such as fitting a more powerful battery. Ensure the ignition is switched off before reconnecting the battery. Then perform the following actions: 1. Set date and time in the information display 3 74. 2. If necessary, activate the power windows and sun roof 3 29, 3 31.
150 Vehicle care Charging the battery 9 Warning On vehicles with stop-start system, ensure that the charging potential does not exceed 14.6 volts when using a battery charger. Otherwise the battery might be damaged. Jump starting 3 178. Warning label Meaning of symbols: ■ No sparks, naked flames or smoking. ■ Always shield eyes. Explosive gases can cause blindness or injury. ■ Keep the battery out of reach of children.
Vehicle care operation 3 times or more while the engine is switched off, to avoid air entering the fuel line. Check diesel fuel filter at shorter intervals if the vehicle is subjected to extreme operating conditions. If there is water in the diesel fuel filter, control indicator N illuminates in the instrument cluster 3 86. Drain the water immediately. Wiper blade replacement Bulb replacement Wiper blades on the windscreen Switch off the ignition and turn off the relevant switch or close the doors.
152 Vehicle care 1. Switch off the ignition and headlight switch. 2. Open the bonnet, release the 11 retainers and remove the radiator cover. 3. Remove 3 bolts and withdraw headlamp. 4. Depress harness connector tags and disconnect headlamp wiring. 5. Remove the headlamp assembly. Headlamp assembly installation is the reverse of removal - ensure locating dowel aligns with its socket. Do not overtighten bolts or retainers.
Vehicle care 5. Engage bulb retaining spring and replace headlamp cap. 6. Reinstall headlamp assembly. Front turn signal 1. Remove headlamp assembly 3 151. 2. Rotate bulb holder anticlockwise and withdraw bulb holder from lamp assembly. 3. Press and rotate bulb anticlockwise to remove it from bulb holder. 4. Insert new bulb into bulb holder by pressing and rotating it clockwise. 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. 6. Reinstall headlamp assembly. Sidelights 1.
154 Vehicle care Low and high beam 9 Danger Xenon headlights work under extremely high electrical voltage. Do not touch. Have bulbs replaced by a workshop. Front turn signal 1. Remove headlamp assembly 3 151. 2. Rotate bulb holder anticlockwise and withdraw bulb holder from lamp assembly. 3. Press and rotate bulb anticlockwise to remove it from bulb holder. 4. Insert new bulb into bulb holder by pressing and rotating it clockwise. 5. Reinstall bulb holder in lamp assembly by rotating it clockwise. 6.
Vehicle care 1. Remove 2 screws from panel on underside of vehicle below front fog lights and remove panel. 2. Disconnect harness connector from bulb holder and rotate bulb holder anticlockwise. 3. Remove bulb holder from lamp assembly, rotate bulb anticlockwise and remove from bulb holder. 4. Insert new bulb into bulb holder and rotate it clockwise. 5. Reinstall bulb holder in lamp assembly and reconnect harness connector. 6. Reinstall panel to underside of vehicle using 2 screws removed earlier.
156 Vehicle care Side turn signal lights Centre high-mounted brake light Have bulbs replaced by a workshop. Number plate light 5. Reinstall bulb holder into lamp assembly, rotate bulb holder clockwise and ensure it is secure. 6. Replace lamp covers using the 4 screws removed earlier. Interior lights Front reading lights 1. Using a suitable screwdriver, pry lamp assembly away from wing. 2. Rotate bulb holder anticlockwise. 3. Remove bulb from lamp assembly by pulling bulb straight out of bulb holder.
Vehicle care Rear reading lights Load compartment light 157 Electrical system Fuses 1. Using a suitable screwdriver, pry lamp lens away from roof lining. 2. Remove bulb. 3. Insert new bulb. 4. Reinstall lamp lens in roof lining. 1. Using a suitable screwdriver, remove lens from lamp assembly. 2. Remove bulb. 3. Insert new bulb. 4. Reinstall lens to lamp assembly. Glovebox light Have bulbs replaced by a workshop. Instrument panel illumination Have bulbs replaced by a workshop.
158 Vehicle care It is advisable to carry a full set of spare fuses. Spare fuses can be stored in the engine compartment fuse box. Fuse extractor A fuse extractor may be located in the engine compartment fuse box. Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse.
Vehicle care Engine compartment fuse box The fuse box is located next to the coolant reservoir in the engine compartment. To open, disengage cover and tilt upwards.
160 Vehicle care
Vehicle care 161 Fuse Circuit Fuse Circuit Fuse Circuit ABS Anti-lock Brake System FAN1 Cooling fan LO BEAM RH A/C Climate control, air conditioning system FAN3 Cooling fan Low beam (righthand) FRT FOG Front fog lights PRK LP LH FRT WPR Front wiper Parking light (lefthand) Fuel pump, vacuum pump PRK LP RH Parking light (right-hand) PWM FAN Pulse width modu‐ lation fan BATT1 Instrument panel fuse box FUEL/VAC BATT2 Instrument panel fuse box HDLP WASHER Headlight washer BATT
162 Vehicle care After changing of defective fuses close the fuse box cover and press until it engages. If the fuse box cover is not closed correctly, malfunctions may occur. Instrument panel fuse box The fuse box is located on the lefthand side of the front passenger seat foot well, or, in right-hand drive vehicles, on the left-hand side of the driver's seat foot well. Release latch to open cover.
Vehicle care 163
164 Vehicle care Fuse Circuit Fuse Circuit Fuse Circuit AMP Amplifier CIM HVAC BLWR APO JACK (CONSOLE) Power outlet (centre console) Communica‐ tions Integration Module Climate control, air conditioning fan APO JACK (REAR CARGO) Power outlet (load compart‐ ment) CLSTR Instrument cluster IPC Instrument panel cluster DRL ISRVM/RCM AWD/VENT All-wheel drive, ventilation Daytime running lights DR/LCK Driver door lock Interior mirror, remote compass module BCM (CTSY) Courtesy lights
Vehicle care Fuse Circuit Fuse Circuit Vehicle tools RUN 2 Power battery key on run XBCM Export Body Control Module Tools RUN/CRNK Run crank XM/HVAC/DLC Vehicles with spare wheel SDM (BATT) Safety Diag‐ nosis Module (Battery) XM satellite radio, climate control, data link connection SDM (IGN 1) Safety Diag‐ nosis Module (Ignition) SPARE - S/ROOF Sunroof S/ROOF BATT Sunroof battery SSPS Power steering STR/WHL SW Steering wheel TRLR Trailer TRLR BATT Trailer battery 165 After
166 Vehicle care Remove wing bolt from the jack by rotating it anticlockwise and remove the jack and wheel wrench bag. Remove straps holding the bag containing the wheel wrench. Remove wheel wrench from the bag. Vehicles with tyre repair kit The jack and vehicle tools are in a storage compartment below the floor cover in the load compartment. To remove the jack and vehicle tools, open the tailgate. Push both levers on the floor cover towards the handle and pull up the floor cover by the handle.
Vehicle care the floor cover by the handle. Hang the hook to the upper part of the tailgate opening. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. Wheels and tyres Tyre condition, wheel condition Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking. Regularly check the wheels for damage.
168 Vehicle care 104 = Load index e.g. 91 is equivalent to 618 kg H = Speed code letter Speed code letter: Q = up to 100 mph S = up to 112 mph T = up to 118 mph H = up to 130 mph V = up to 150 mph W = up to 168 mph Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey. Do not forget the spare wheel. This also applies to vehicles with tyre pressure monitoring system. Use the valve cap key to make unscrewing the valve caps easier.
Vehicle care pressures are detected. In some versions, the message is displayed in abbreviated form. For example, the following messages can be displayed: A graphic indicating the left rear tyre is shown together with the current tyre pressure; slight pressure deviation. Reduce speed. Check tyre pressure at next opportunity with an appropriate gauge and correct if necessary. On the Colour-Info-Display, this message will appear in yellow.
170 Vehicle care Changing tyre and wheel size The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI). Their position is indicated by markings on the sidewall. If there is more wear at the front than the rear, swap round front wheels and rear wheels. Ensure that the direction of rotation of the wheels is the same as before. Tyres age, even if they are not used. We recommend tyre replacement every 6 years.
Vehicle care Tyre chains Tyre chains are permitted only on tyres of size 215/70 R 16. We recommend you consult your service partner. The use of tyre chains is not permitted on the temporary spare wheel. If the use of tyre chains is required after suffering a flat front tyre, fit the temporary spare wheel on the rear axle and transfer one of the rear wheels to the front axle. Tyre repair kit Tyre chains are only permitted on the front wheels.
172 Vehicle care Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. 1. Release the sealant filler hose 1 and the power plug 2. 2. Unscrew valve cap from defective tyre. Screw the sealant filler hose onto the tyre valve. 3. Connect the power plug to the power outlet or cigarette lighter socket. Unplug all items from other power outlets. 4. Switch on ignition.
Vehicle care is obtained, switch off the compressor. If the prescribed tyre pressure is not obtained within 10 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation. Reattach the tyre repair kit and continue the filling procedure for 10 minutes. If the prescribed tyre pressure is still not obtained, the tyre is too badly damaged. Seek the assistance of a workshop. Drain excess tyre pressure with the button next to the pressure gauge. Do not run the compressor for longer than 10 minutes. 8.
174 Vehicle care 13. Turn the selector switch clockwise to the air only position. Switch on the compressor to inflate the tyre with air only. Notice The driving characteristic of the repaired tyre is severely affected, therefore have this tyre replaced. If unusual noise is heard or the compressor becomes hot, turn compressor off for at least 30 minutes. Note the expiry date of the kit. After this date its sealing capability is no longer guaranteed.
Vehicle care ■ Do not raise the vehicle more than is necessary to change a wheel. ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle. ■ Do not start the engine when it is raised on the jack. ■ Clean wheel nuts and thread before mounting the wheel. 175 1. Pull off the wheel cover. 2. Install the wheel wrench ensuring that it locates securely and loosen each wheel nut by one turn by turning anticlockwise.
176 Vehicle care 5. Attach wheel wrench to eye of threaded rod and rotate wrench clockwise to raise vehicle. If this is not the case, carefully lower the vehicle immediately and reposition the jack. Raise the vehicle until the wheel is just clear of the ground. 6. Unscrew wheel nuts completely and wipe clean with a cloth. Do not grease the threads. Put wheel nuts somewhere where the threads will not be soiled. 7. Change the wheel. Notes on spare wheel 3 177. 8.
Vehicle care tyre renewed as soon as possible and have the wheel balanced and fitted to the vehicle. Front arm position of the lifting platform centrically under the recess of the sill. Spare wheel Temporary spare wheel Some vehicles are equipped with a tyre repair kit instead of a spare wheel. The temporary spare wheel is designed for use on your vehicle only. Use of the temporary spare wheel could affect driveability, particularly if using winter tyres.
178 Vehicle care The following applies to tyres fitted opposing the rolling direction: ■ Driveability may be affected. Have the defective tyre renewed as soon as possible and have the wheel balanced and fitted to the vehicle. ■ Do not drive faster than 50 mph. ■ Drive particularly carefully on wet and snow-covered road surfaces. 9 Warning Storing a jack, a wheel or other equipment in the load compartment could cause injury if they are not fixed in place properly.
Vehicle care ■ A discharged battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the same voltage (12 Volts). Its capacity (Ah) must not be much less than that of the discharged battery. ■ Use jump leads with insulated terminals and a cross section of at least 16 mm2 (25 mm2 for diesel engines).
180 Vehicle care 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Operate discharged vehicle for approx. 20 minutes to allow for adequate battery recharging. 6. Reverse above sequence exactly when removing leads. Towing Towing the vehicle Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral. Switch on the hazard warning lights on both vehicles.
Vehicle care To prevent the entry of exhaust fumes from the towing vehicle, switch on the air recirculation system 3 111 and close the windows. Vehicles with manual transmission and All-wheel drive: If the vehicle is towed with all four wheels on the ground then there are no technical limitations for speed and distance. If only one axle has been raised, the maximum speed is 30 mph. There is no distance limitation.
182 Vehicle care Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using de-icing agent, have the locks regreased by a workshop. Washing The paintwork of your vehicle is exposed to environmental influences. Wash and wax your vehicle regularly. When using automatic car washes, select a programme that includes waxing.
Vehicle care Windows and windscreen wiper blades Use a soft lint-free cloth or chamois leather together with window cleaner and insect remover. When cleaning the rear window, make sure the heating element inside is not damaged. For mechanical removal of ice, use a sharp-edged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass. Clean smearing wiper blades with a soft cloth and window cleaner.
184 Vehicle care Rear carrier system Clean the rear carrier system with a steam-jet or high-pressure jet cleaner at least once a year. Operate the rear carrier system once in a while if not in regular use, in particular during winter. Interior care Interior and upholstery Only clean the vehicle interior, including the instrument panel fascia and panelling, with a dry cloth or interior cleaner. Clean the leather upholstery with clear water and a soft cloth. In case of heavy soiling, use leather care.
Service and maintenance Service and maintenance General information ................... 185 Recommended fluids, lubricants and parts .................................... 186 General information Service information 185 Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland, United Kingdom.
186 Service and maintenance Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty. 9 Warning Operating materials are hazardous and could be poisonous. Handle with care. Pay attention to information given on the containers. Engine oil Engine oil is identified by its quality and its viscosity.
Service and maintenance Coolant and antifreeze Use only silicate-free long life coolant (LLC) antifreeze. The system is factory filled with coolant designed for excellent corrosion protection and frost protection down to approx. -28 °C. In northern countries with very low temperatures the factory filled coolant provides frost protection down to approx. -37°C. This concentration should be maintained all year round.
188 Technical data Technical data Vehicle identification .................. 188 Vehicle data ............................... 190 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is also engraved on the top right-hand side of the bulkhead near the centre of the engine firewall. The Vehicle Identification Number is visible through the windscreen.
Technical data Identification plate Information on identification label: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Identification Number 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gross train weight in kg 6 = Maximum permissible front axle load in kg 7 = Maximum permissible rear axle load in kg 8 = Vehicle-specific or countryspecific data The identification plate is located on the front left door frame.
190 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Serbia, Turkey) Engine oil quality Only Israel Petrol engines (including E85) Diesel engines Petrol engines (including E85) Diesel engines dexos 1 – – ✔ – dexos 2 ✔ ✔ – ✔ In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.
Technical data International service schedule Required engine oil quality All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including E85) Diesel engines Petrol engines (including E85) Diesel engines dexos 1 ✔ – – – dexos 2 – ✔ ✔ ✔ In case dexos quality is unavailable you may use the oil qualities listed below: All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey
192 Technical data All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including E85) Diesel engines Petrol engines (including E85) Diesel engines ACEA A3/B3 ✔ – ✔ – ACEA A3/B4 ✔ ✔ ✔ ✔ ACEA C3 ✔ ✔ ✔ ✔ API SM ✔ – ✔ – API SN resource conserving ✔ – ✔ – Engine oil viscosity grades All countries outside Europe (except Israel), including Belarus, Moldova, Russia, Serbia, Turkey Ambient temperature Petrol and
Technical data 193 Engine data Sales designation 2.4 3.0 V6 2.2 CDTI 2.
194 Technical data Performance All-wheel drive Engine A 24 XF A 30 XF A 22 DM A 22 DMH Manual transmission 115 – 116 124 Automatic transmission 109 123 113 119 A 24 XF A 30 XF A 22 DM A 22 DMH Manual transmission 118 – 117 – Automatic transmission – – 114 – Maximum speed3) [mph] Front-wheel drive Engine Maximum speed3) [mph] 3) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload.
Technical data Vehicle weight Kerb weight, basic model without any optional equipment Manual transmission / Automatic transmission.
196 Technical data Turning circle diameter, wall to wall [m] 12.78 Turning circle diameter, kerb to kerb [m] 11.
Technical data Capacities Engine oil Engine A 24 XF A 30 XF A 22 DM A 22 DMH including filter [l] 4.7 5.7 5.6 5.6 between MIN and MAX [l] 1.0 1.0 1.0 1.
198 Technical data Tyre pressures Up to full load Engine Tyres All 4) Up to full load ECO Trailer towing front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 240/2.4 (35) 240/2.4 (35) 260/2.6 (38) 260/2.6 (38) 240/2.4 (35) 280/2.8 (41) T 155/90 R 16 420/4.2 (60) (Temporary spare) 420/4.2 (60) – – 420/4.2 (60) 420/4.
Technical data Towing hitch installation dimensions Dimension mm A 412 B 505 C 482 D 734 E 1039 F (fully laden) 363 G (at kerb weight) 481 199
200 Technical data
Customer information Customer information Vehicle data recording and privacy ....................................... 201 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data.
202 Customer information In addition, the manufacturer may use the collected or received diagnostic data: ■ for the manufacturer's research needs ■ to make it available for research needs where appropriate confidentiality is maintained and need is shown ■ to share summary data which is not tied to a specific vehicle with other organisations for research purposes Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition syste
Customer information 203
204 Index A Accessories and vehicle modifications .......................... 143 Accessory sockets........................ 75 Active head restraints................... 33 Adjustable air vents ................... 114 Airbag and belt tensioners ........... 81 Airbag deactivation ...................... 45 Airbag system .............................. 43 Air conditioning regular operation ................................ 115 Air conditioning system .............. 111 Air intake ...............................
205 Change engine oil ....................... 86 Changing tyre and wheel size . . . 170 Charging system .......................... 81 Check control................................ 96 Child locks ................................... 21 Child restraint installation locations ................................... 48 Child restraint systems ................ 47 Cigarette lighter ........................... 76 Cleaning the vehicle................... 182 Climate control ............................. 14 Clock ........
206 Glovebox ..................................... 52 Graphic-Info-Display, ColourInfo-Display .............................. 91 H Halogen headlights .................... 152 Hand brake................................. 129 Hazard warning flashers ............ 104 Headlight flash ........................... 103 Headlight range adjustment ...... 103 Headlights.......................... 103, 151 Headlights when driving abroad 104 Headlight washer.......................... 71 Head restraint adjustment .......
207 Performance .............................. 194 Performing work ........................ 144 Pollen filter ................................. 115 Power outlets ............................... 75 Power seat adjustment ................ 36 Power steering ............................. 84 Power steering fluid ................... 147 Power windows ............................ 29 Preheating ................................... 85 R Radio Frequency Identification (RFID).....................................
208 Tyre changing............................. 174 Tyre designations ...................... 167 Tyre pressure ...................... 96, 168 Tyre pressure monitoring system............................... 96, 168 Tyre pressures ........................... 198 Tyre repair kit ............................. 171 Tyres .......................................... 167 Tyres and wheel size, changing. 170 U Ultrasonic parking assist ...... 84, 135 Underseat storage ....................... 53 Upholstery, cleaning....
