Owner’s Manual Model Year 2014 Edition: July 2013 KTA-2744/2-VX-en 0-1 VAUXHALL Adam Owner’s Manual Model Year 2014 Edition: July 2013 KTA-2744/2-VX-en
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 30 Storage ........................................ 49 Instruments and controls ............. 68 Lighting ...................................... 101 Climate control ........................... 109 Driving and operating ................. 118 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction Danger, Warnings and Cautions 9 Danger Text marked 9 Danger provides information on risk of fatal injury. Disregarding this information may endanger life. 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3.
Introduction 5
6 In brief In brief Vehicle unlocking Initial drive information Press button c to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, press the brand emblem at the bottom half. Radio remote control 3 19, Central locking system 3 20, Load compartment 3 22.
In brief Seat adjustment Seat backrests Seat height Turn handwheel to adjust inclination. Do not lean on backrest while adjusting. Seat position 3 31, Seat adjustment 3 32, Seat folding 3 33. Lever pumping motion up = seat higher down = seat lower 7 Seat positioning Pull handle, slide seat, release handle. Seat position 3 31, Seat adjustment 3 32. 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. Seat position 3 31, Seat adjustment 3 32.
8 In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Press release button, adjust height, engage. Head restraints 3 30. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat position 3 31, Seat belts 3 34, Airbag system 3 37.
In brief Exterior mirrors Steering wheel adjustment Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 25, Electric adjustment 3 25, Folding exterior mirrors 3 26, Heated exterior mirrors 3 26. Unlock the lever, adjust the steering wheel, then engage the lever and ensure it is fully locked. Do not adjust the steering wheel unless the vehicle is stationary and the steering wheel lock has been released. Airbag system 3 37, Ignition positions 3 119.
10 In brief Instrument panel overview
In brief 1 2 3 Power windows ..................... 27 Exterior mirrors ..................... 25 Cruise control ..................... 129 Eco button for stop-start system ................................. 120 Speed limiter ....................... 130 Side air vents ...................... 116 Turn and lane-change signals, headlight flash, low beam and high beam .... 104 Seat heating .......................... 34 4 5 Parking assist ..................... 131 Heated steering wheel ..........
12 In brief Exterior lighting Turn light switch: 7 = lights off 8 = sidelights 9 = headlights Headlight flash, high beam and low beam Automatic light control AUTO = automatic light control: exterior lighting is switched on and off automatically m = activation or deactivation of the automatic light control = sidelights 8 = headlights 9 Rear fog light Press r in the light switch.
In brief Turn and lane-change signals Hazard warning flashers Horn lever up = right turn signal lever down = left turn signal Operated with the ¨ button. Hazard warning flashers 3 103. Press j. Turn and lane-change signals 3 104, Parking lights 3 104.
14 In brief Washer and wiper systems Windscreen washer Rear window wiper Pull lever. Windscreen washer system 3 70, Washer fluid 3 153. Press the rocker switch to activate the rear window wiper: upper switch = continuous operation lower switch = intermittent operation middle = off position Windscreen wiper 2 = fast 1 = slow P = interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down.
In brief Rear window washer Climate control Heated rear window, heated exterior mirrors Push lever. Washer fluid is sprayed on the rear window and the wiper wipes a few times. Rear window wiper/washer 3 71. The heating is operated by pressing the Ü button. Heated rear window 3 29. 15 Demisting and defrosting the windows ■ Switch on cooling n. ■ Set temperature control to warmest level. ■ Set fan speed to highest level. ■ Set air distribution control to l. ■ Switch on heated rear window Ü.
16 In brief Transmission Starting off Manual transmission Check before starting off Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal and then press the release button on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection. Manual transmission 3 123. ■ Tyre pressure and condition 3 171, 3 206. ■ Engine oil level and fluid levels 3 151.
In brief Stop-start system If the vehicle is at a low speed or at a standstill and certain conditions are fulfilled, activate an Autostop as follows: ■ Depress the clutch pedal ■ set the lever in neutral ■ release the clutch pedal An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer. To restart the engine, depress the clutch pedal again. Stop-start system 3 120. Parking ■ Always apply the parking brake. Activate the manual parking brake without pressing the release button.
18 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 22 Vehicle security ............................ 23 Exterior mirrors ............................ 25 Interior mirrors ............................. 26 Windows ...................................... 27 Roof .............................................
Keys, doors and windows Radio remote control Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system ■ Power windows The radio remote control has a range of approx. 20 metres. It can be restricted by external influences. The hazard warning flashers confirm operation. Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
20 Keys, doors and windows Extend the key and open the unit. Replace the battery (battery type CR 2032), paying attention to the installation position. Close the unit and synchronise. Key with fixed key section Have the battery replaced by a workshop. Radio remote control synchronisation After replacing the battery, unlock the door with the key in the driver's door lock. The radio remote control will be synchronised when the ignition is switched on.
Keys, doors and windows The setting can be saved for the key being used. Memorised settings 3 20. Unlocking and opening the tailgate 3 22. Central locking buttons Locks or unlocks doors, the load compartment and fuel filler flap from inside the passenger compartment. 21 Fault in radio remote control system Unlocking Locking Close doors, load compartment and fuel filler flap. Press the e button to lock. Press the c button to unlock. Press button e.
22 Keys, doors and windows Fault in central locking system Unlocking Manually unlock the driver's door by turning the key in the lock. The passenger door can be opened by pulling the interior handle twice. The load compartment and fuel filler flap cannot be opened. To deactivate the anti-theft locking system, switch on the ignition 3 24. Additionally it is configurable to unlock the driver's door or both doors after the ignition is switched off and the ignition key is removed.
Keys, doors and windows Closing General hints for operating tailgate 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases, which cannot be seen or smelled, could enter the vehicle. This can cause unconsciousness and even death. Use interior handle. Do not press the touchpad switch or the emblem whilst closing as this will unlock the tailgate again. Central locking system 3 20.
24 Keys, doors and windows Activating Activation ■ Self-activated 30 seconds after locking the vehicle (initialisation of the system) ■ Press button e on the radio remote control twice within 15 seconds. Status LED Status during the first 30 seconds of anti-theft alarm system activation: LED = test, arming delay. illuminates LED flashes = doors, tailgate or quickly bonnet not completely closed, or system fault. Status after system is armed: LED flashes = system is armed.
Keys, doors and windows The alarm can be silenced by pressing any button on the radio remote control or by switching on the ignition. The anti-theft alarm system can only be deactivated by pressing button c on the radio remote control or by switching on the ignition. A triggered alarm, which has not been interrupted by the driver, will be indicated by the hazard warning lights. They will flash quickly three times when the vehicle is unlocked with the radio remote control. Vehicle messages 3 92.
26 Keys, doors and windows In position 0 no mirror is selected. Heated mirrors Interior mirrors Manual anti-dazzle Folding mirrors For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time.
Keys, doors and windows Automatic anti-dazzle 27 Windows Windscreen Windscreen stickers Do not attach stickers such as toll road stickers or similar on the windscreen in the area of the interior mirror. Otherwise the detection zone of the sensor in the mirror housing could be restricted. Power windows Dazzle from following vehicles at night is automatically reduced. 9 Warning Take care when operating the power windows. Risk of injury, particularly to children. Be careful when closing the windows.
28 Keys, doors and windows Initialising the power windows Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again. Override safety function In the event of closing difficulties due to frost or the like, switch on the ignition, then pull the switch to the first detent and hold. The window moves up without safety function enabled. To stop movement, release the switch.
Keys, doors and windows Heated rear window A ticket holder is located on the backside of the sun visor. 29 Roof Glass panel Sunblind Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. If the sun visors have integral mirrors, the mirror covers should be closed when driving.
30 Seats, restraints Seats, restraints Head restraints ............................ 30 Front seats ................................... 31 Seat belts ..................................... 34 Airbag system .............................. 37 Child restraints ............................. 43 Head restraints Adjustment Position Front head restraints, height adjustment 9 Warning Only drive with the head restraint set to the proper position. Press release button, adjust height, engage.
Seats, restraints 31 Front seats Rear head restraints, height adjustment Seat position 9 Warning Only drive with the seat correctly adjusted. Pull the head restraint upwards and let engage. To move downwards, press the catch to release and push the head restraint downwards. Removal of rear head restraint E.g. when using a child restraint system 3 43. Press both catches, pull the head restraint upwards and remove.
32 Seats, restraints ■ Sit with shoulders as far back against the backrest as possible. Set the backrest rake so that it is possible to easily reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel. Do not angle the backrest too far back. We recommend a maximum rake of approx. 25°. ■ Adjust the steering wheel 3 68. ■ Set seat height high enough to have a clear field of vision on all sides and of all display instruments.
Seats, restraints 33 Seat backrests Seat height Seat folding Turn handwheel to adjust inclination. Do not lean on backrest while adjusting. Lever pumping motion up = seat higher down = seat lower Pull release lever towards the front and fold backrest forwards. Then slide seat forwards to the stop. To restore, slide the seat backwards to the stop. Lift backrest to upright position without operating the release lever. Let backrest engage.
34 Seats, restraints Caution When seat height is in the highest position, push head restraints down and fold up sun visors before folding backrest forwards. Seat heating is operational when engine is running and during an Autostop. Stop-start system 3 120. Seat belts Heating The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore the risk of injury is considerably reduced.
Seats, restraints Seat belts are designed to be used by only one person at a time. Child restraint system 3 43. Periodically check all parts of the belt system for damage, pollution and proper functionality. Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop. Note Make sure that the belts are not damaged by shoes or sharp-edged objects or trapped. Prevent dirt from getting into the belt retractors.
36 Seats, restraints Removing Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing. Seat belt reminder X 3 81. To release belt, press red button on belt buckle. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen.
Seats, restraints Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered, the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Note The airbag systems and belt pretensioner control electronics are located in the centre console area.
38 Seats, restraints geschützt ist, da dies den TOD oder SCHWERE VERLETZUNGEN DES KINDES zur Folge haben kann. FR: NE JAMAIS utiliser un siège d'enfant orienté vers l'arrière sur un siège protégé par un COUSSIN GONFLABLE ACTIF placé devant lui, sous peine d'infliger des BLESSURES GRAVES, voire MORTELLES à l'ENFANT. ES: NUNCA utilice un sistema de retención infantil orientado hacia atrás en un asiento protegido por un AIRBAG FRONTAL ACTIVO. Peligro de MUERTE o LESIONES GRAVES para el NIÑO.
Seats, restraints zalecenia może być przyczyną ŚMIERCI lub POWAŻNYCH OBRAŻEŃ u DZIECKA. TR: Arkaya bakan bir çocuk emniyet sistemini KESİNLİKLE önünde bir AKTİF HAVA YASTIĞI ile korunmakta olan bir koltukta kullanmayınız. ÇOCUK ÖLEBİLİR veya AĞIR ŞEKİLDE YARALANABİLİR. UK: НІКОЛИ не використовуйте систему безпеки для дітей, що встановлюється обличчям назад, на сидінні з УВІМКНЕНОЮ ПОДУШКОЮ БЕЗПЕКИ, інакше це може призвести до СМЕРТІ чи СЕРЙОЗНОГО ТРАВМУВАННЯ ДИТИНИ.
40 Seats, restraints LV: NEKĀDĀ GADĪJUMĀ neizmantojiet uz aizmuguri vērstu bērnu sēdeklīti sēdvietā, kas tiek aizsargāta ar tās priekšā uzstādītu AKTĪVU DROŠĪBAS SPILVENU, jo pretējā gadījumā BĒRNS var gūt SMAGAS TRAUMAS vai IET BOJĀ. ET: ÄRGE kasutage tahapoole suunatud lapseturvaistet istmel, mille ees on AKTIIVSE TURVAPADJAGA kaitstud iste, sest see võib põhjustada LAPSE SURMA või TÕSISE VIGASTUSE. Beyond the warning required by ECE R94.
Seats, restraints The side airbag system consists of an airbag in each front seat backrest. The location is identified by the word AIRBAG. The side airbag system is triggered in the event of a side impact of a certain severity. The ignition must be switched on. 41 9 Warning Keep the area in which the airbag inflates clear of obstructions. Note Only use protective seat covers that have been approved for the vehicle. Be careful not to cover the airbags.
42 Seats, restraints Airbag deactivation The front passenger airbag system must be deactivated if a child restraint system is to be fitted on this seat. The side airbag and curtain airbag systems, the belt pretensioners and all driver airbag systems will remain active. The front passenger airbag system can be deactivated via a keyoperated switch on the right side of the instrument panel.
Seats, restraints Change status only when the vehicle is stopped with the ignition off. Status remains until the next change. Control indicator for airbag deactivation 3 82.
44 Seats, restraints backbone, which is still very weak, is under less strain in the event of an accident. Suitable are restraint systems that comply with ECE 44-03 or ECE 44-04. Check local laws and regulations for mandatory use of child restraint systems. Ensure that the child restraint system to be installed is compatible with the vehicle type. Ensure that the mounting location of the child restraint system within the vehicle is correct.
Seats, restraints 45 Child restraint installation locations Permissible options for fitting a child restraint system On front passenger seat Weight and age class activated airbag deactivated airbag On rear seats Group 0: up to 10 kg or approx. 10 months X U1 U2 Group 0+: up to 13 kg or approx. 2 years X U1 U2 Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U2, 3 Group II: 15 to 25 kg or approx. 3 to 7 years X X U Group III: 22 to 36 kg or approx.
46 Seats, restraints Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear seats Group 0: up to 10 kg E ISO/R1 X IL * Group 0+: up to 13 kg E ISO/R1 X IL * D ISO/R2 X X C ISO/R3 X X D ISO/R2 X X C ISO/R3 X X B ISO/F2 X IL, IUF** B1 ISO/F2X X IL, IUF** A ISO/F3 X IL, IUF** Group I: 9 to 18 kg IL = Suitable for particular ISOFIX restraint systems of the "specific-vehicle", "restricted" or
Seats, restraints ISOFIX size class and seat device A – ISO/F3 B – ISO/F2 B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Rear-facing child restraint system for children of maximum size in the weight class up to 18 kg.
48 Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. The vehicle is equipped with guides in the backrests to support the installation of the child restraint system. Open the flaps of the guides to mount a child restraint system. Remove rear head restraint before mounting a child restraint system, if required 3 45.
Storage Storage Storage compartments ................ 49 Load compartment ....................... 60 Roof rack system ......................... 66 Loading information ..................... 66 Storage compartments 9 Warning Do not not store heavy or sharp objects in the storage compartments. Otherwise, the storage compartment lid could open and vehicle occupants could be injured by objects being thrown around in the event of sharp braking, a sudden change in direction or an accident.
50 Storage Additional cupholders or bottleholders are located in the rear side panels. Front storage Flexible cupholder strap Door pockets in both doors are designed to carry bottles. A movable rubber strap is located in the storage compartment in front of the gear selector lever. Pull out the strap to fix a cup or ashtray. Storage compartments are located below the light switch, in the centre console in front of the gear selector lever, in the door pockets and in the side panels near the rear seats.
Storage Rear carrier system Rear carrier system for two bicycles electrically-powered bicycle to the pull-out carrier. The maximum load on the adapter is 20 kg. The wheelbase of a bicycle must not exceed 1.15 metre. Otherwise the secure fastening of a bicycle is not possible. If not in use, the carrier system must be slid back into the vehicle floor. There must not be any objects on the bicycles that could become loose during transportation.
52 Storage Pull release lever up. The system disengages and travels quickly out of the bumper. will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop. Fold out tail lamps Unfold number plate light Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again.
Storage Swivel both tail lamps backwards as far as it will go. 53 Lock the rear carrier system Assembling the bicycle rack Remove strap and swivel both clamping levers sidewards as far as it will go. Otherwise safe functionality is not guaranteed. Lift the rack at the rear (1) and pull it backwards. Fold up the rack (2). Fold out wheel recess Remove strap and fold out the wheel recess.
54 Storage Press button (1) and remove left part of rack (2). Push down the rack (1) and swivel handle (2) backwards to engage. Press button (1) and insert left part of rack into the right part (2). Attaching the adapter When carrying two bicycles, the adapter must be fixed before attaching the first bicycle. 1. Apply the adapter to the rear carrier system as shown in the illustration.
Storage 2. Turn the lever (1) forwards and hold, then lower the adapter (2) at the rear. 3. Release lever and check if the adapter is engaged securely. 4. Guide the strap attached to the adapter underneath the lever for folding back the rear carrier system. Fasten the strap. 55 Attaching the first bicycle 1. Rotate the pedals into position as shown in the illustration and put the bicycle on the wheel recess. Make sure that the bicycle stands centrally on the wheel recesses. 2.
56 Storage 3. Secure both bicycle wheels to the wheel recesses using the strap retainers. 4. Check the bicycle to make sure it is secure. Caution Ensure gap between bicycle and vehicle is at least 5 cm. If necessary, loosen handlebar and swivel sideways. Attaching the second bicycle The attachment of a second bicycle is similar to the attachment of the first bicycle. Additionally some steps must be considered: 1. Always rotate the pedals into an appropriate position before putting on the bicycle. 2.
Storage Removing bicycles Undo strap retainers on both bicycle tyres. Turn knob anti-clockwise and remove mounting brackets. ■ Without attached adapter: Detaching adapter 1. Fold in wheel recesses. Push the lever (1) to disengage and hold. Pull the rack (2) backwards to fold the rear carrier system. ■ With attached adapter: 9 Warning Take care when disengaging the rear carrier system as it will tilt backwards. Risk of injury.
58 Storage 3. Turn the lever (1) forwards and hold. 4. Lift the adapter (2) at the rear and remove. Disassembling the bicycle rack Press button (1) and reinstall rack (2). Press button (1) and remove upper part of rack (2). Arrange mounting bracket as shown in the illustration. Swivel handle (1) sidewards to disengage and lift the rack (2).
Storage 59 Swivel both clamping levers inwards as far as it will go. Fasten strap. Fold in tail lamps Fold the rack backwards, then push forwards until it stops (1). Press the rack down at the rear (2). Fold in wheel recess Fold in wheel recess. Fasten strap. Stow the strap retainers accurately. Unlock the rear carrier system First swivel tail lamps (1) forwards as far as it will go. Then swivel hinges (2) forwards as far as it will go.
60 Storage Load compartment Fold in number plate light The rear seat backrest is divided into two parts. Both parts can be folded down separately. Load compartment extension Remove the load compartment cover if necessary. Press the catch and push down the head restraint. Fold number plate light forwards. Retracting the rear carrier system Caution Take care that all foldable parts, e.g. wheel recesses and mounting brackets, are stowed accurately.
Storage do so may result in personal injury or damage to load or vehicle in the event of heavy braking or collision. Hook for carrier bags Pull the strap on one or both backrests and fold them down onto the seat cushion. To fold up, raise the backrests into upright position and let them engage audibly. The backrests are properly engaged when the red marks on both release straps are not visible. 9 Warning When folding up, ensure that backrests are securely locked in position before driving.
62 Storage ■ raise the lashing eyes on both sides and turn the lock hooks to the front to fix the box to the lashing eyes, ■ raise rear backrests and install load compartment cover, ■ if equipped, stow the suitcase with tyre repair kit in a chamber of the storage box, ■ close and lock the cover. ■ turn the lock hooks on both sides to the rear and push down the lashing eyes in the recesses, ■ raise the storage box and place it on the folded backrests, ■ remove storage box out of the load compartment.
Storage Rear floor storage cover 63 Removal Rear floor cover Lift up rear floor cover. Depending on the version, there are vehicle tools, jacking equipment or a tyre repair kit under the floor cover. Tools 3 169, tyre repair kit 3 175. Rear floor cover on version with subwoofer box Lift up rear part of floor cover to gain access to the warning triangle. When closing floor cover, ensure it is fixed with the Velcro fastener.
64 Storage General hint Lashing eyes 9 Warning ■ move floor cover slowly to the front, taking care that the guiding bolts slide into the attachments of the load compartment, and allow the floor cover to lower into position, ■ close the floor cover by folding the upper part to the rear, and fix it with the Velcro fastener, ■ fold up rear backrests.
Storage Warning triangle The warning triangle is stowed with elastic straps in the load compartment below the tailgate. If the vehicle is equipped with a storage box in the load compartment, remove the storage box to gain access to the warning triangle 3 61. 65 First aid kit Version with subwoofer box: lift up the rear part of the load compartment floor cover. Pull the handle to remove the warning triangle. Rear floor storage cover 3 63.
66 Storage Roof rack system Loading information Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. For further information contact your workshop. Follow the installation instructions and remove the roof rack when not in use. Mounting roof rack Open the cover from each mounting point by using a coin. ■ Heavy objects in the load compartment should be placed against the seat backrests. Ensure that the backrests are securely engaged.
Storage 9 Warning Always make sure that the load in the vehicle is securely stowed. Otherwise objects can be thrown around inside the vehicle and cause personal injury or damage to the load or car. ■ The payload is the difference between the permitted gross vehicle weight (see identification plate 3 196) and the EC kerb weight. To calculate the payload, enter the data for your vehicle in the Weights table at the front of this manual.
68 Instruments and controls Instruments and controls Controls Steering wheel controls Steering wheel adjustment Controls ....................................... 68 Warning lights, gauges and indi‐ cators ........................................... 76 Information displays ..................... 86 Vehicle messages ........................ 92 Trip computer ............................... 95 Vehicle personalisation ................
Instruments and controls Heated steering wheel Activate heating by pressing * button. Activation is indicated by the LED in the button. Horn The recommended grip areas of the steering wheel are heated quicker and to a higher temperature than the other areas. Heating is operational when the engine is running and during an Autostop. Stop-start system 3 120. Press j.
70 Instruments and controls Windscreen wiper/washer Adjustable wiper interval Automatic wiping with rain sensor Wiper lever in position P. Turn the adjuster wheel to adjust the desired wipe interval: short = turn adjuster wheel interval upwards long = turn adjuster wheel interval downwards P = automatic wiping with rain sensor Windscreen wiper 2 1 P § = = = = fast slow interval wiping off For a single wipe when the windscreen wiper is off, press the lever down.
Instruments and controls Adjustable sensitivity of the rain sensor 71 Pull lever. Washer fluid is sprayed onto the windscreen and the wiper wipes a few times. Rear window wiper/washer Keep the sensor free from dust, dirt and ice.
72 Instruments and controls Outside temperature A drop in temperature is indicated immediately and a rise in temperature after a time delay. Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the rear window is frozen. Switch off in car washes. The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged. Activation or deactivation of this function can be changed in the Info-Display.
Instruments and controls If outside temperature drops to 3 °C, a warning message is displayed in the Driver Information Centre with Uplevel-Display. 9 Warning Note Find a detailed description of the menu operation in the user guide for the Infotainment system. Graphic-Info Display Press the CONFIG button to open the Settings menu. Scroll through the list and select the menu item Time Date to display the respective submenu.
74 Instruments and controls Set date format To switch between the available options, repeatedly press the MENUTUNE knob. RDS clock synchronization The RDS signal of most VHF transmitters automatically sets the time. RDS time synchronisation can take a few minutes. Some transmitters do not send a correct time signal. In such cases, it is recommended to switch off the automatic time synchronisation. To switch between the options On and Off, repeatedly press the MENUTUNE knob.
Instruments and controls Power outlets Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries. Do not damage the outlet by using unsuitable plugs. Stop-start system 3 120. 75 Ashtrays Caution To be used only for ash and not for combustible rubbish. Cigarette lighter A 12 Volt power outlet is located in the centre console. Do not exceed the maximum power consumption of 120 watts. With ignition off, the power outlet is deactivated.
76 Instruments and controls Warning lights, gauges and indicators Odometer Tachometer The bottom line displays the recorded distance in miles. Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Instrument cluster The needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer Trip odometer Indicates vehicle speed. The top line displays the recorded distance since the last reset.
Instruments and controls Fuel gauge Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity. Fuel selector 77 As soon as the liquid gas tank is empty, petrol operation is automatically engaged until the ignition is switched off. Fuel for liquid gas operation 3 143. Engine coolant temperature gauge Displays the fuel level or gas level in the tank depending on the operation mode. Control indicator Y illuminates if the level in the tank is low.
78 Instruments and controls Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. Service display The engine oil life system lets you know when to change the engine oil and filter. Based on driving conditions, the interval at which an engine oil and filter change will be indicated can vary considerably. In the Uplevel-Display, the remaining oil life duration is displayed in the Vehicle Information Menus.
Instruments and controls ignition is switched on, most control indicators will illuminate briefly as a functionality test.
80 Instruments and controls Control indicators in the instrument cluster
Instruments and controls Control indicators in the centre console Bulb replacement 3 156, Fuses 3 164. Turn signals 3 104. 81 Seat belt status on rear seats Seat belt reminder Seat belt reminder on front seats X for driver's seat illuminates or flashes red in the tachometer. k for front passenger seat illuminates or flashes red in the centre console, when the seat is occupied. Turn signal O illuminates or flashes green. Illuminates briefly The parking lights are switched on.
82 Instruments and controls Airbag and belt tensioners v illuminates red. When the ignition is switched on, the control indicator illuminates for approx. 4 seconds. If it does not illuminate, does not go out after 4 seconds or illuminates whilst driving, there is a fault in the airbag system. Seek the assistance of a workshop. The airbags and belt pretensioners may fail to trigger in the event of an accident. Deployment of the belt pretensioners or airbags is indicated by continuous illumination of v.
Instruments and controls Flashes when the engine is running Fault that could lead to catalytic converter damage. Ease up on the accelerator until the flashing stops. Seek the assistance of a workshop immediately. Service vehicle soon g illuminates yellow. Additionally a warning message or a warning code is displayed. The vehicle needs a service. Seek the assistance of a workshop. Vehicle messages 3 92. Brake and clutch system Brake and clutch fluid level R illuminates red.
84 Instruments and controls Illuminates with power steering reduced Interference due to external sources of ultrasound. Once the source of interference is removed, the system will operate normally. Have the cause of the fault in the system remedied by a workshop. Ultrasonic parking assist 3 131. stability, however, may deteriorate depending on road surface conditions. Have the cause of the fault remedied by a workshop. Electronic Stability Control 3 126, Traction Control system 3 126.
Instruments and controls Engine oil pressure I illuminates red. Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. Illuminates when the engine is running Caution Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels. 1. Depress clutch. 2. Select neutral gear. 3. Move out of the flow of traffic as quickly as possible without impeding other vehicles. 4. Switch off ignition.
86 Instruments and controls Illuminates green Cruise control is active. Cruise control 3 129. Door open h illuminates red. A door or the tailgate is open. Information displays Driver Information Centre ■ trip/fuel information ■ vehicle messages, displayed as code numbers 3 92. The Driver Information Centre (DIC) is located in the instrument cluster between speedometer and tachometer. It is available as Midlevel-Display or Uplevel-Display.
Instruments and controls Some of the displayed functions differ when the vehicle is being driven or at a standstill. Some functions are only available when the vehicle is being driven. Vehicle personalisation 3 97. Memorised settings 3 20. Press the SET/CLR button to select a function or to confirm a message. Vehicle Information Menu X Selecting menus and functions The menus and functions can be selected via the buttons on the turn signal lever.
88 Instruments and controls ■ Speed Warning: if exceeding the preset speed, a warning chime will be activated Selection and indication can be different between Midlevel- and Uplevel-Display. Trip/Fuel Information Menu W ■ Remaining Oil Life: indicates when to change the engine oil and filter 3 78 Press the MENU button to select W in the top line of the UplevelDisplay. Turn the adjuster wheel to select a submenu. Press the SET/CLR button to confirm.
Instruments and controls 89 Submenus are: ■ Shift indication: Current gear is indicated inside an arrow. The figure above recommends upshifting for fuel saving reasons. Eco index display: The current fuel consumption is indicated on a segment display. For economical driving, adapt your driving style to keep the filled segments within the Eco area. The more segments are filled, the higher the fuel consumption. Simultaneously the current consumption value is indicated.
90 Instruments and controls Graphic-Info-Display, Colour-Info-Display Depending on the vehicle configuration the vehicle has a ■ Graphic-Info-Display or ■ Colour-Info-Display with TouchScreen functionality. Both displays are located in the instrument panel.
Instruments and controls The Colour-Information-Display indicates in colour: ■ time 3 73 ■ outside temperature 3 72 ■ date 3 73 ■ electronic climate control settings 3 112 ■ parking assist and advanced parking assist instructions 3 131 ■ Infotainment system, see description in the Infotainment manual ■ navigation, see description in the Infotainment manual ■ system messages ■ vehicle messages 3 92 ■ settings for vehicle personalisation 3 97 The type of information and how it is displayed depends on the equi
92 Instruments and controls Vehicle messages Messages are indicated mainly in the Driver Information Centre (DIC), in some cases together with a warning and signal buzzer. Vehicle messages on the Midlevel-Display 5 Steering wheel is locked 7 Turn steering wheel, switch ignition off and then on 9 Turn steering wheel, start engine again 12 Vehicle overloaded 13 Compressor overheated 15 Centre high-mounted brake light failure 16 Brake light failure 17 Headlight levelling malfunction No.
Instruments and controls No. Vehicle message No.
94 ■ ■ ■ ■ ■ ■ ■ ■ ■ Instruments and controls Lighting, bulb replacement Wiper/washer system Doors, windows Radio remote control Seat belts Airbag systems Engine and transmission Tyre pressure Vehicle battery Vehicle messages on the Colour-Info-Display Some important messages appear additionally in the Colour-Info-Display. Some messages only pop up for a few seconds. Warning chimes When starting the engine or whilst driving Only one warning chime will sound at a time.
Instruments and controls Trip computer ■ Trip odometer 1 ■ Average consumption 1 ■ Average speed 1 The menus and functions can be selected via the buttons on the turn signal lever 3 86. Trip/Fuel Information Menu on Uplevel-Display Turn the adjuster wheel to select the submenus: Press the MENU button to select W on the Uplevel-Display.
96 Instruments and controls When the fuel level in the tank is low, a message appears on vehicles with Uplevel-Display. When the tank must be refuelled immediately, a warning code or warning message is displayed on vehicles with Midlevel- and UplevelDisplay. Additionally the control indicator Y in the fuel gauge illuminates or flashes 3 85.
Instruments and controls On vehicles with LPG engines: Average consumption is indicated for the currently selected mode; LPG or Gasoline. Instantaneous consumption Display of the instantaneous consumption. On vehicles with LPG engines: Instantaneous consumption is indicated for the currently selected mode; LPG or Gasoline. Average speed Display of average speed. The measurement can be reset at any time. To reset, press the SET/CLR button for a few seconds.
98 Instruments and controls In the corresponding submenus the following settings can be changed: Languages Selection of the desired language. Time Date See Clock 3 73. Radio settings See Infotainment manual for further information. Phone settings See Infotainment manual for further information. Vehicle settings ■ Climate and air quality Auto fan speed: Modifies the level of the cabin airflow of the climate control in automatic mode.
Instruments and controls Time & date settings See Clock 3 73. Auto relock doors: Activates or deactivates the automatic relock function after unlocking without opening the vehicle. ■ Restore factory settings: Reset all settings to the default settings. Radio settings See Infotainment manual for further information. Connection settings See Infotainment manual for further information. Personal settings in the Colour-Info-Display When audio is switched on, press ; on the control panel. Press Settings.
100 Instruments and controls Personalization by driver: Activates or deactivates the personalisation function. Auto wipe in reverse gear: Activate or deactivate automatic switching on of the rear window wiper when reverse gear is engaged. ■ Collision / detection Park assist: Activate or deactivate the ultrasonic sensors. Side blind zone alert: Changes the settings for the side blind spot alert system. ■ Lighting Exit lighting: Activates or deactivates and changes the duration of exit lighting.
Lighting Lighting Exterior lighting Light switch 101 Light switch with Automatic light control Exterior lighting .......................... 101 Interior lighting ........................... 105 Lighting features ........................ 107 Turn light switch: 7 = lights off 8 = sidelights 9 = headlights Control indicator 8 3 85. Turn light switch: AUTO = automatic light control: low beam is switched on and off automatically depending on external lighting conditions.
102 Lighting The current status of the automatic light control is displayed In the Driver Information Centre with UplevelDisplay. When switching on the ignition, automatic light control is active. When headlights are on, 8 lights up. Control indicator 8 3 85. Tail lights Tail lights are illuminated together with headlights and sidelights.
Lighting Headlight range adjustment Manual headlight range adjustment To adapt headlight range to the vehicle load to prevent dazzling: turn thumb wheel ? to required position. 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden 3 = driver's seat occupied and load compartment laden. Headlights when driving abroad The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side.
104 Lighting Turn and lane-change signals Switch the turn signal off manually by moving the lever to its original position. Parking lights Rear fog lights lever up = right turn signal lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated. For three flashes, e.g. when changing lanes, press the lever until resistance is felt and then release.
Lighting Reversing lights The reversing light comes on when the ignition is on and reverse gear is selected. Interior lighting Instrument panel illumination control Misted light covers 105 Turn thumb wheel A and hold until the desired brightness is obtained. On vehicles with light sensor, the brightness can only be adjusted when the exterior lights are on and the light sensor detects night conditions.
106 Lighting Operate rocker switch: w = automatic switching on and off. press u = on. press v = off. Ambient light comes on automatically when switching off ignition and extinguishes after opening a door. Pressing button m after switching off ignition; ambient light remains on for 60 minutes. It is also activated with Entry lighting 3 107 and Exit lighting 3 107. Note In the event of an accident with airbag deployment the courtesy lights are turned on automatically.
Lighting Operate button with ignition switched on: m one brief = on or off. press T repeated = dimming stepwise. brief presses T long press = dimming continuously. The selected intensity remains the next time the ignition is switched on. Starlight comes on automatically when switching off ignition and extinguishes after opening a door. Pressing button m after switching off ignition; ambient light remains on for 60 minutes. It is also activated with Entry lighting 3 107 and Exit lighting 3 107.
108 Lighting Path lighting Headlights, tail lights, reversing lights and number plate lights illuminate the surrounding area for an adjustable time after leaving the vehicle. Activating Exit lighting is switched off immediately if the turn signal lever is pulled while the driver's door is open. Activation, deactivation and duration of this function can be changed in the Info-Display. Vehicle personalisation 3 97. The settings can be saved for the key being used 3 20.
Climate control Climate control Climate control systems ............. 109 Air vents ..................................... 116 Maintenance .............................. 117 Climate control systems Heating and ventilation system 109 Heating will not be fully effective until the engine has reached normal operating temperature. Fan speed Adjust the air flow by switching the fan to the desired speed.
110 Climate control Demisting and defrosting the windows Note If air distribution mode l is selected while engine is running, an Autostop will be inhibited until another air distribution is selected. If air distribution mode l is selected while the engine is in an Autostop, the engine will restart automatically. Stop-start system 3 120.
Climate control Press button n again to switch off cooling. The air conditioning system cools and dehumidifies (dries) as soon as the outside temperature is slightly above the freezing point. Therefore condensation may form and drip from under the vehicle. If no cooling or drying is required, switch off the cooling system to save fuel. Activated cooling might inhibit Autostops. Stop-start system 3 120. Air recirculation system 4 111 Press button to activate air recirculation mode.
112 Climate control Demisting and defrosting the windows V Note If air distribution mode l is selected while engine is running, an Autostop will be inhibited until another air distribution is selected. If air distribution mode l is selected while the engine is in an Autostop, the engine will restart automatically. Stop-start system 3 120. Electronic climate control system ■ Switch on cooling n. ■ Set temperature control to warmest level. ■ Set fan speed to highest level.
Climate control Climate control settings are shown on the Graphic-Info-Display, or depending on the version, on ColourInfo-Display. Setting modifications are briefly popped-up in both displays, superimposed over the currently displayed menu. The electronic climate control system is only fully operational when the engine is running. Automatic mode AUTO Basic setting for maximum comfort: ■ Press AUTO button, the air distribution and fan speed are regulated automatically.
114 Climate control Demisting and defrosting the windows V Setting of automatic rear window heating can be changed in the Info-Display. Vehicle personalisation 3 97. Fan speed Z Note If the V button is pressed while the engine is running, an Autostop will be inhibited until the V button is pressed again. If the V button is pressed while the engine is in an Autostop, the engine will restart automatically. Stop-start system 3 120. ■ Press button V. Activation is indicated by the LED in the button.
Climate control Air distribution Cooling n Turn right rotary knob for desired adjustment. Setting is indicated in the Info-Display. K = to foot well 9 = to windscreen, front door windows and foot well s = to windscreen and front door windows M = to head area via adjustable air vents L = to head area and foot well Press button n to switch on cooling. Activation is indicated by the LED in the button. Cooling is only functional when the engine is running and climate control fan is switched on.
116 Climate control Press button 4 to activate air recirculation mode. Activation is indicated by the LED in the button. Press button 4 again to deactivate recirculation mode. Air vents Adjustable air vents At least one air vent must be open while the cooling is on. 9 Warning The exchange of fresh air is reduced in air recirculation mode. In operation without cooling the air humidity increases, so the windows may mist up from inside.
Climate control Maintenance Air intake Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when the outside temperature is too low. Service The air intake in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow.
118 Driving and operating Driving and operating Driving hints ............................... 118 Starting and operating ............... 118 Engine exhaust .......................... 123 Manual transmission .................. 123 Brakes ........................................ 124 Ride control systems ................. 126 Driver assistance systems ......... 129 Fuel ............................................
Driving and operating Ignition switch positions Power to the Infotainment system will continue to operate for 30 minutes or until the key is removed from the ignition switch, regardless of whether any door will be opened. Starting the engine The following electronic systems can work until the driver's door is opened or at the latest for 10 minutes after the ignition is switched off: ■ Power windows ■ Power outlets Before restarting or to switch off the engine, turn the key back to position 0.
120 Driving and operating Possible reasons for a non-starting engine: ■ Clutch pedal not operated ■ Timeout occurred Turbo engine warm-up Upon start-up, engine available torque may be limited for a short time, especially when the engine temperature is cold. The limitation is to allow the lubrication system to fully protect the engine. Overrun cut-off The fuel supply is automatically cut off during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released.
Driving and operating An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer. During an Autostop, the heating and brake performance will be maintained.
122 Driving and operating Restart of the engine by the stop-start system The selector lever must be in neutral to enable an automatic restart.
Driving and operating Engine exhaust 9 Danger Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled. If exhaust gases enter the interior of the vehicle, open the windows. Have the cause of the fault rectified by a workshop. Avoid driving with an open load compartment, otherwise exhaust gases could enter the vehicle. Catalytic converter The catalytic converter reduces the amount of harmful substances in the exhaust gases.
124 Driving and operating Caution It is not advisable to drive with the hand resting on the selector lever. Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly. Considerably more force is needed for this. The braking distance is extended. Seek the assistance of a workshop before continuing your journey.
Driving and operating Parking brake Fault 9 Warning Manual parking brake If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available. During hard braking, the vehicle can no longer be steered and may swerve. 125 Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking).
126 Driving and operating Ride control systems Fault If there is a fault in the system the control indicator b lights up continuously and a message or a warning code appears in the Driver Information Centre. The system is not operational. Have the cause of the fault remedied by a workshop. Traction Control system The Traction Control system (TC) is a component of the Electronic Stability Control (ESC).
Driving and operating Fault If there is a fault in the system the control indicator b lights up continuously and a message or a warning code appears in the Driver Information Centre. The system is not operational. Have the cause of the fault remedied by a workshop. 127 Activation City mode ESC is operational after each engine start as soon as the control indicator b extinguishes. When ESC operates b flashes. 9 Warning Do not let this special safety feature tempt you into taking risks when driving.
128 Driving and operating Stop-start system 3 120. Fault Deactivation Press button B; LED in the button extinguishes and a message pops-up in the Driver Information Centre. Each time the engine is started, City mode is deactivated. Overload If the steering in City mode is heavily loaded, e.g. in long parking manoeuvres or heavy city traffic, the system is deactivated for overheat protection. Steering operates in normal mode until City mode activates automatically.
Driving and operating Driver assistance systems Vehicle speed can be increased by depressing the accelerator pedal. When the accelerator pedal is released, the previously stored speed is resumed. Cruise control remains activated while gearshifting. 9 Warning Driver assistance systems are developed to support the driver and not to replace his attention. The driver accepts full responsibility when driving the vehicle.
130 Driving and operating Reduce speed Resume stored speed With cruise control active, hold thumb wheel turned to SET/- or briefly turn to SET/- repeatedly: speed decreases continuously or in small increments. Turn thumb wheel to RES/+ at a speed above 20 mph. The stored speed will be obtained. Deactivation Press button m, control indicator m in instrument cluster extinguishes. The stored speed is deleted.
Driving and operating Alternatively accelerate to the desired speed and briefly turn thumb wheel to SET/-: the current speed is stored as maximum speed. Speed limit is displayed in the Driver Information Centre. Change speed limit With speed limiter active, turn thumb wheel to RES/+ to increase or SET/to decrease the desired maximum speed.
132 Driving and operating The rear parking assist makes parking easier by measuring the distance between the vehicle and rear obstacles. It informs and warns the driver by giving acoustic signals. Indication The system warns the driver with acoustic signals against potentially hazardous obstacles behind the vehicle in a distance range up to 1.5 metre. The interval between the sounds becomes shorter as the vehicle gets closer to that obstacle.
Driving and operating The front-rear parking assist measures the distance between the vehicle and obstacles in front and behind the vehicle. The system gives acoustic signals and display messages. The system has six ultrasonic parking sensors each in the rear and front bumper. It uses two different acoustic warning signals for the front and rear monitoring areas, each with a different tone frequency.
134 Driving and operating Operation When reverse gear is engaged, the front and rear parking assist is ready to operate. An illuminated LED in the parking assist button D indicates that the system is ready to operate. The front parking assist can also be activated at a speed up to 7 mph with a brief press of the parking assist button. If the D button is switched on once within an ignition cycle, the front parking assist is deactivated at a speed above 7 mph.
Driving and operating In the Colour-Info-Display, distance is displayed by coloured zones in front of or behind the vehicle. The distance indication in the Driver Information Centre can be inhibited by vehicle messages with a higher priority. After approving the message by pressing the SET/CLR button on the turn signal lever, distance indication appears again. Fault In the event of a fault or if the system does not work temporarily, e.g.
136 Driving and operating Button logic operates the systems by pressing as follows: ■ If only front-rear parking assist is active, a brief press deactivates front-rear parking assist. ■ If only front-rear parking assist is active, long press activates advanced parking assist. ■ If only advanced parking assist is active, a brief press activates frontrear parking assist. ■ If only advanced parking assist is active, long press deactivates advanced parking assist.
Driving and operating 137 If the driver does not stop the vehicle within 10 metres for parallel parking slots or 6 metres for perpendicular parking slots after a parking slot is proposed, the system starts to search for another suitable parking slot. Parking slot searching mode Select parallel or perpendicular parking slot on Driver Information Centre by pressing the SET/CLR button or on Colour-Info Display tap icon 6 or 7.
138 Driving and operating A brief vibration in the steering wheel after engaging reverse gear indicates that the steering is controlled by the system. Then the vehicle is steered into the slot automatically by giving the driver detailed instructions for braking, accelerating and gear shifting. The driver must keep hands away from the steering wheel. Pay always attention on the sound of the front-rear parking assist. Continuous sound means that the distance to an obstacle is less than approx. 30 cm.
Driving and operating The display shows the type of parking slot. Changing the parking side If the system is equipped with ColourInfo-Display, select the type of parking slot by tapping the display icon 6 or 7. The system is configured to detect parking slots by default on the passenger side. To detect parking slots on the driver side, switch on turn indicator to the driver side for the durance of the search.
140 Driving and operating Basic notes on parking assist systems ■ exceeding number of maximum gear changes: 8 parking cycles when parallel parking or 5 cycles when perpendicular parking, ■ switching off the ignition. Deactivation by the driver or by the system during manoeuvring will be indicated by Parking Deactivated in the Driver Information Centre or Colour-Info-Display. Additionally an acoustic signal sounds.
Driving and operating correct distance indication in the upper part of these vehicles cannot be guaranteed. Objects with a very small reflection cross-section, e.g. objects of narrow size or soft materials, may not be detected by the system. Parking assist systems do not detect objects outside the detection range. Note It is possible that the sensor detects a non-existing object caused by echo disturbance from external acoustic noise or mechanical misalignments (sporadic false warnings might happen).
142 Driving and operating When the system detects a vehicle in the side blind zone while driving forward, either while passing a vehicle or being passed, an amber warning symbol B will light up in the relevant exterior mirror. If the driver then activates the turn signal, the warning symbol B starts flashing amber as a warning not to change lanes. will extinguish the warning symbols. If a vehicle is then detected in the blind zone, the warning symbols B will illuminate as normal on the relevant side.
Driving and operating Fuel Caution Fuel for petrol engines Only use unleaded fuel that complies with European standard EN 228 or E DIN 51626-1 or equivalent. Your engine is capable of running with E10 fuel that fulfills these standards. E10 fuel contains up to 10 % bioethanol. Use fuel with the recommended octane rating 3 201. Use of fuel with too low an octane rating can reduce engine power and torque and slightly increases fuel consumption.
144 Driving and operating Pressing the LPG button switches between petrol and liquid gas operation as soon as the required parameters (coolant temperature, gas temperature and minimum engine speed) have been reached. The requirements are usually fulfilled after approx. 60 seconds (depending on exterior temperature) and the first firm press on the accelerator. The LED status shows the current operating mode.
Driving and operating Refuelling 145 Fuel filler flap is located at right rear side of the vehicle. 9 Danger Before refuelling, switch off the engine. Switch off any mobile phones. Follow the operating and safety instructions of the gas station when refuelling. 9 Danger Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this remedied immediately by an authorized dealer.
146 Driving and operating Liquid gas refuelling Follow the operating and safety instructions of the filling station when refuelling. The filling valve for the liquid gas is behind the fuel filler cap. Fit the required adapter. Unscrew protective cap from the filler neck. ACME Adapter: Screw the nut of the filling nozzle onto the adapter. Press locking lever on filler nozzle down. DISH (Italy) filler neck: Place the filler nozzle into the adapter. Press locking lever on filler nozzle down.
Driving and operating Bayonet adapter: Netherlands, Norway, Spain, United Kingdom 9 Warning Due to the system design, an escape of liquid gas after releasing the locking lever is unavoidable. Avoid inhaling. 9 Warning The liquid gas tank may only be filled to 80% for safety reasons. The multivalve on the liquid gas tank automatically limits the fill quantity. If a larger quantity is added, we recommend not exposing the vehicle to the sun until the excess amount has been used up.
148 Driving and operating DISH (Italy) adapter: BosniaHerzegovina, Bulgaria, Denmark, Estonia, France, Greece, Italy, Croatia, Latvia, Lithuania, Macedonia, Austria, Poland, Portugal, Romania, Sweden, Switzerland, Serbia, Slovakia, Slovenia, Czech Republic, Turkey, Ukraine, Hungary Fuel filler cap Only use genuine fuel filler caps. Fuel consumption - CO2Emissions The fuel consumption (combined) of the model Vauxhall Adam is within a range of 57 to 51 mpg.
Vehicle care Vehicle care General Information ................... 149 Vehicle checks ........................... 150 Bulb replacement ....................... 156 Electrical system ........................ 164 Vehicle tools .............................. 169 Wheels and tyres ....................... 170 Jump starting ............................. 186 Towing ....................................... 188 Appearance care .......................
150 Vehicle care ■ Open the bonnet, close all doors and lock the vehicle. ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft alarm system. Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir. ■ Check the engine oil level.
Vehicle care 151 If the bonnet is opened during an Autostop, the engine will be restarted automatically for safety reasons. 9 Danger The ignition system uses extremely high voltage. Do not touch. Closing Before closing the bonnet, press the support into the holder. Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. Bonnet Opening Push the safety catch upwards and open the bonnet. Pull the release lever and return it to its original position.
152 Vehicle care Engine coolant Caution The coolant provides freeze protection down to approx. -28 °C. In northern countries with very low temperatures the factory filled coolant provides frost protection down to approx. -37 °C. It is the owner's responsibility to maintain the proper level of an appropriate quality oil in the engine. Insert dipstick to the stop on the handle and make half a turn. Caution Only use approved antifreeze.
Vehicle care tap water. Install the cap tightly. Have the coolant concentration checked and have the cause of the coolant loss remedied by a workshop. Washer fluid 153 Caution Only washer fluid with a sufficient antifreeze concentration provides protection at low temperatures or a sudden drop in temperature. Brakes In the event of minimum thickness of the brake lining, a squealing noise sounds during braking. Continued driving is possible but have the brake lining replaced as soon as possible.
154 Vehicle care Vehicle battery The brake fluid level must be between the MIN and MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop. Only use high-performance brake fluid approved for the vehicle. Brake and clutch fluid 3 194. Vehicles without stop-start system will be equipped with a lead acid battery.
Vehicle care must be closed off with a dummy cap, and the ventilation in the vicinity of the negative terminal must be opened. Only use batteries that allow the fuse box to be mounted above the vehicle battery. In vehicles with stop-start system, be sure to have the AGM (Absorptive Glass Mat) battery replaced with another AGM battery Note Using an AGM battery different from the original Vauxhall battery might result in a lower performance of the stop-start system.
156 Vehicle care ■ See the Owner's manual for further information. ■ Explosive gas may be present in the vicinity of the battery. Wiper blade on the rear window Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment.
Vehicle care 157 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder with the clip downwards and engage into the reflector until it clicks. 5. Install cap. High beam (2) Low beam outer bulb (1). High beam inner bulb (2). 2. Press the clip to disengage bulb holder. Withdraw the bulb holder from the reflector. Low beam (1) 1. Rotate the cap anticlockwise and remove it. 1. Rotate the cap anticlockwise and remove it.
158 Vehicle care Sidelight/Daytime running light (3) Version with bulb 2. Press the clip to disengage bulb holder. Withdraw the bulb holder from the reflector. 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder with the clip upwards and engage into the reflector until it clicks. 5. Install cap. 1. Rotate bulb socket (3) anticlockwise to disengage. Withdraw the bulb socket from the headlamp housing. 2. Remove the bulb from the socket by pulling. 3.
Vehicle care Front turn signal lights 2. Undo screw and remove light assembly from the bumper. 4. Remove bulb by turning anticlockwise a little and withdrawing. Replace the bulb. 5. Insert the bulb socket into the assembly and turn clockwise. 6. Attach light assembly into the bumper and fix with the screw. 7. Insert cover into the bumper and fix with the screw. Tail lights 1. Undo screw and remove cover. 159 3. Disengage and remove the bulb socket by turning anticlockwise. 1.
160 Vehicle care Version with subwoofer box: remove load compartment floor cover, on right side also remove the tool box to gain access to the cover 3 63. Version with storage box: remove storage box to gain access to the cover 3 61. 3. Carefully withdraw the light assembly from the recesses and remove. 2. Unscrew the plastic securing nut from the inside by hand. 4. Turn bulb holder anticlockwise and remove.
Vehicle care 161 Fit light assembly with the retaining pins into the recesses of the vehicle body and tighten the securing nut from inside the load compartment. Pull the circular gasket over the recess in the lamp housing. Close cover and engage. Reversing light/rear fog light Reversing light is located on the right side of the bumper, and the rear fog light is located on the left side of the bumper for left-hand drive vehicles, and vice versa for right hand drive models.
162 Vehicle care 4. Remove bulb by turning anticlockwise slightly and withdrawing. Replace the bulb. 5. Insert the bulb socket into the assembly and turn clockwise. 6. Replace light assembly in the bumper and fix with the screw. 7. Insert cover into the bumper and fix with the screw. 1. On left vehicle side, slide lamp to the front and remove it out of the wing with the rear end. On right vehicle side, slide lamp to the rear and remove it out of the wing with the front end.
Vehicle care Number plate light 163 4. Pull bulb from bulb holder and replace it. 5. Insert bulb holder into lamp housing and turn clockwise. 6. Insert lamp into bumper and let engage. Interior lights Courtesy light, reading lights Have bulbs replaced by a workshop. 1. Insert screwdriver in recess of the cover, press to the side and release spring. 2. Remove lamp downwards, taking care not to pull on the cable. Load compartment light Have bulbs replaced by a workshop.
164 Vehicle care Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. There are two fuse boxes in the vehicle: ■ in the front left of the engine compartment, ■ in left-hand drive vehicles behind the light switch, or, in right-hand drive vehicles, behind the glovebox. Before replacing a fuse, turn off the respective switch and the ignition. There are different kinds of fuses in the vehicle.
Vehicle care Engine compartment fuse box The fuse box is in the front left of the engine compartment. Disengage the cover and fold it upwards until it stops. Remove the cover vertically upwards. No.
166 Vehicle care No. Circuit No. Circuit No.
Vehicle care Instrument panel fuse box In left-hand drive vehicles, the fuse box is behind the light switch in the instrument panel. Hold the handle, then pull and fold down the light switch. In right-hand drive vehicles, the fuse box is located behind a cover in the glovebox. Open the glovebox, then open the cover and fold it down.
168 Vehicle care No. Circuit No. Circuit No.
Vehicle care 169 Vehicle tools Tools Vehicles with tyre repair kit Some tools and the towing eye are located together with the tyre repair kit in a tool box in the load compartment below the floor cover. On version with storage box, remove box first 3 61. On versions with rear carrier system or liquid gas engine, the tools are located together with the towing eye and tyre repair kit in a suitcase, fixed with a strap at the left sidewall in the load compartment.
170 Vehicle care Vehicles with spare wheel Wheels and tyres Tyre condition, wheel condition On version with subwoofer box, the tools and the towing eye are located together with the tyre repair kit and the warning triangle in the box below the floor cover. To gain access, remove floor cover: fold rear part to the front and pull out the cover to the rear 3 63.
Vehicle care Tyre designations E.g. 195/55 R 16 95 H 195 = Tyre width, mm 55 = Cross-section ratio (tyre height to tyre width), % R = Belt type: Radial RF = Type: RunFlat 16 = Wheel diameter, inches 95 = Load index e.g. 95 is equivalent to 690 kg H = Speed code letter Speed code letter: Q = up to 100 mph S = up to 112 mph T = up to 118 mph H = up to 130 mph V = up to 150 mph W = up to 168 mph Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey.
172 Vehicle care If the tyre pressure must be reduced or increased on a vehicle with tyre pressure monitoring system, switch off ignition. After adjusting tyre pressure switch on ignition and select the relevant setting on the page Tyre load in the Driver Information Centre, 3 86. The current tyre pressures can be shown in the Vehicle Information Menu in the Driver Information Centre with Uplevel-Display. The menu can be selected with the buttons on the turn signal lever.
Vehicle care A detected low tyre pressure condition is indicated by the control indicator w 3 84. If w illuminates, stop as soon as possible and inflate the tyres as recommended 3 206. After inflating, driving may be required to update the tyre pressure values in the Driver Information Centre. During this time w may illuminate. If w illuminates at lower temperatures and extinguishes after driving, this could be an indicator for getting low pressure. Check tyre pressure. Vehicle messages 3 92.
174 Vehicle care Select: ■ Light for comfort pressure up to 3 people ■ Eco for Eco pressure up to 3 people ■ Max for full loading The tyre pressure value displayed in the Driver Information Centre shows the actual tyre pressure. Therefore it is important to check tyre pressure with cold tyres. Auto learn function Check tread depth at regular intervals. Tyres should be replaced for safety reasons at a tread depth of 2-3 mm (4 mm for winter tyres).
Vehicle care Changing tyre and wheel size If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the speedometer as well as the nominal tyre pressure and make other vehicle modifications. After converting to a different tyre size, have the label with tyre pressures replaced. 9 Warning Use of unsuitable tyres or wheels may lead to accidents and will invalidate the vehicle type approval.
176 Vehicle care Tyre damage exceeding 4 mm or that is at tyre's sidewall cannot be repaired with the tyre repair kit. The tyre repair kit is in the tool box under the floor cover in the load compartment. 9 Warning Do not drive faster than 50 mph. Do not use for a lengthy period. Steering and handling may be affected. If you have a flat tyre: Apply the parking brake and engage first gear.
Vehicle care On versions with subwoofer box the tyre repair kit is located in the box under the floor cover in the load compartment. To use tyre repair kit, firstly remove floor cover: fold rear part to the front and pull out the cover to the rear 3 63. 177 4. Screw the compressor air hose to the connection on the sealant bottle. 5. Fit the sealant bottle into the retainer on the compressor. Set the compressor near the tyre in such a way that the sealant bottle is upright. 3.
178 Vehicle care 9. Connect the compressor plug to the power outlet or cigarette lighter socket. To avoid discharging the battery, we recommend running the engine. 12. All of the sealant is pumped into the tyre. Then the tyre is inflated. 13. The prescribed tyre pressure should be obtained within 10 minutes. Tyre pressure 3 206. When the correct pressure is obtained, switch off the compressor. 14. 15. 10. Set the rocker switch on the compressor to I. The tyre is filled with sealant. 11.
Vehicle care hose directly onto tyre valve and compressor when doing this. If tyre pressure is more than 1.3 bar, set it to the correct value. Repeat the procedure until there is no more loss of pressure. If the tyre pressure has fallen below 1.3 bar, the vehicle must not be used. Seek the assistance of a workshop. 18. Stow away tyre repair kit in load compartment. On version with subwoofer install floor cover. Rear floor storage cover 3 63.
180 Vehicle care ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle. ■ Do not start the vehicle when it is raised on the jack. ■ Clean wheel bolts and thread with a clean cloth before mounting the wheel. 1. Disengage wheel bolt caps with a screwdriver and remove. Pull off the wheel cover with the hook. Vehicle tools 3 169. Alloy wheels: Disengage wheel bolt caps with a screwdriver and remove.
Vehicle care Some versions have sill panellings with covered vehicle jacking points: pull out the cover at the respective jacking point firstly. 4. Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping. 5. 6. 7. 8. 9. Attach jack handle and with the jack correctly aligned rotate handle until wheel is clear of the ground. Unscrew the wheel bolts. Change the wheel. Spare wheel 3 182 Screw on the wheel bolts. Lower vehicle.
182 Vehicle care Rear arm position of the lifting platform centrically under the recess of the sill. The spare wheel has a steel rim. Caution The use of a spare wheel that is smaller than the other wheels or in combination with winter tyres could affect driveability. Have the defective tyre replaced as soon as possible. Front arm position of the lifting platform at the underbody. Spare wheel Some vehicles are equipped with a tyre repair kit instead of a spare wheel.
Vehicle care 4. Lift the spare wheel holder a bit by hand and unhook the catch. 5. Lower the spare wheel holder. 183 11. Close the empty spare wheel holder by turning the hexagon bolt clockwise successively using the wheel wrench. 12. Stow wheel wrench and the jack in the tool box in vehicle floor. 13. Close the load compartment floor. Stowing a damaged wheel in the load compartment 6. Lift the spare wheel holder a bit by hand and detach the safety cable. 7.
184 Vehicle care 2. Untwist wing nut and remove tool box. 3. Position the damaged wheel to stand upright into the tool box spare, facing to the front. 4. Remove strap 1 from the tool box and place the loop end of the strap through the right side lashing eye. 5. Place the hook end of the strap through the loop and pull it until the strap is fastened securely to the lashing eye. 6. Insert the strap through the spokes of the wheel as shown in the illustration. 7.
Vehicle care 185 4. Take strap 1 and place the loop end of the strap through the right side lashing eye. 5. Place the hook end of the strap through the loop and pull it until the strap is fastened securely to the lashing eye. 9. Position the tool box in the inside of the wheel and secure it with strap 2 inserted through two spokes of the wheel. Wheels with tyre size bigger than 195/55R16 1. Fold down backrests of the rear seats 3 60. 2. Remove strap 1 from the tool box. 3.
186 Vehicle care 9 Warning Storing a jack, a wheel or other equipment in the load compartment could cause injury if they are not fixed properly. During a sudden stop or a collision, loose equipment could strike someone. Store jack and tools always in the respective storage compartments and secure them by fixing. Damaged wheel placed in the load compartment must always be secured by the strap. Temporary spare wheel The use of the temporary spare wheel could affect driveability.
Vehicle care ■ Never expose the battery to naked flames or sparks. ■ A discharged vehicle battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the same voltage (12 Volts). Its capacity (Ah) must not be much less than that of the discharged battery.
188 Vehicle care 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Reverse above sequence exactly when removing leads. Towing Towing the vehicle Disengage the cap by pushing on the marked position. The towing eye is stowed with the vehicle tools 3 169. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye.
Vehicle care Caution 189 Towing another vehicle Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. When the engine is not running, considerably more force is needed to brake and steer. To prevent the entry of exhaust gases from the towing vehicle, switch on the air recirculation and close the windows. Seek the assistance of a workshop. After towing, unscrew the towing eye. Insert cap and engage in the bumper.
190 Vehicle care Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. After towing, unscrew the towing eye. Insert cap and engage in the bumper. Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using de-icing agent, have the locks regreased by a workshop.
Vehicle care On vehicles with emblem touchpad: when cleaning with a high-pressure jet cleaner ensure a minimum distance of 30 cm when working around the tailgate to prevent unintended unlocking. Thoroughly rinse and leather-off the vehicle. Rinse leather frequently. Use separate leathers for painted and glass surfaces: remnants of wax on the windows will impair vision. Exterior lights Headlight and other light covers are made of plastic.
192 Vehicle care After the underbody is washed, check the underbody and have it waxed if necessary. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop. Before and after winter, wash the underbody and have the protective wax coating checked. Liquid gas system 9 Danger Liquid gas is heavier than air and can collect in sink points. Take care when performing work at the underbody in a pit.
Service and maintenance Service and maintenance General information ................... 193 Recommended fluids, lubricants and parts .................................... 194 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified. The detailed, up-to-date service schedule for your vehicle is available at the workshop.
194 Service and maintenance Make sure that the Service and Warranty Booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle. Service interval with remaining engine oil life duration The service interval is based on several parameters depending on usage. The service display lets you know when to change the engine oil. Service display 3 78.
Service and maintenance Select the appropriate engine oil based on its quality and on the minimum ambient temperature 3 198. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty. Engine oil viscosity grades The SAE viscosity grade gives information of the thickness of the oil. Multigrade oil is indicated by two figures, e.g. SAE 5W-30.
196 Technical data Technical data Vehicle identification .................. 196 Vehicle data ............................... 198 Vehicle identification Identification plate Vehicle Identification Number The identification plate is located on the left door frame. The Vehicle Identification Number is visible through the windscreen.
Technical data Information on identification label: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Identification Number 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gross train weight in kg 6 = Maximum permissible front axle load in kg 7 = Maximum permissible rear axle load in kg 8 = Vehicle-specific or countryspecific data The combined total of front and rear axle loads must not exceed the permissible gross vehicle weight.
198 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Serbia, Turkey) Only Israel Petrol engines (including CNG, LPG, E85) Petrol engines (including CNG, LPG, E85) dexos 1 – ✔ dexos 2 ✔ – Engine oil quality In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 for topping up once between each oil change.
Technical data International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85) Petrol engines (including CNG, LPG, E85) dexos 1 ✔ – dexos 2 – ✔ Engine oil quality In case dexos quality is unavailable you may use the oil qualities listed below: All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85)
200 Technical data All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85) Petrol engines (including CNG, LPG, E85) ACEA A3/B3 ✔ ✔ ACEA A3/B4 ✔ ✔ ACEA C3 ✔ ✔ API SM ✔ ✔ API SN resource conserving ✔ ✔ Engine oil quality Engine oil viscosity grades All countries outside Europe (except Israel), including Belarus, Moldova, Russia, Serbia, Turkey Ambient temperature Petrol engines down to -25 °C SAE 5W-30 or SAE 5W-
Technical data Engine data Sales designation 1.2 1.4 1.4 LPG 1.4 Engine identifier code A12XEL A14XEL A14XEL A14XER Number of cylinders 4 4 4 4 Piston displacement [cm3] 1229 1398 1398 1398 Engine power [kW] 51 64 64 74 at rpm 5600 6000 6000 6000 Torque [Nm] 115 130 130 130 at rpm 4000 4000 4000 4000 Fuel type Petrol Petrol Liquid Gas/Petrol Petrol recommended 95 95 95 95 possible 98 98 98 98 Gas – – LPG – Oil consumption [l/1000 km] 0.6 0.6 0.
202 Technical data Performance Engine A12XEL A14XEL A14XER Manual transmission 103 109 115 Automatic transmission – – – Maximum speed2) [mph] 2) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
Technical data Vehicle weight Kerb weight, basic model without any optional equipment without/with air conditioning [kg] Engine Manual transmission Automatic transmission A12XEL 1086/1101 – A14XEL 1120/1135 – A14XER 1120/1135 – Kerb weight, basic model with all optional equipment without/with air conditioning [kg] Engine Manual transmission Automatic transmission A12XEL –/1237 – A14XEL –/1237 – A14XER –/1237 – Vehicle dimensions Length [mm] 3698 Width without exterior mirrors [m
204 Technical data Length of load compartment floor [mm] 462 Length of load compartment with folded rear seats [mm] 1041 Load compartment width [mm] 954 Load compartment height [mm] 874 Wheelbase [mm] 2311 Turning circle diameter [m] 10.
Technical data Capacities Engine oil Engine A12XEL A14XEL A14XER including Filter [l] 4.0 4.0 4.0 between MIN and MAX [l] 1.0 1.0 1.
206 Technical data Tyre pressures Engine Tyres A12XEL, 175/70 R14, A14XEL, 185/60 R15, 185/65 R15 A14XER 195/55 R16, 215/45 R17, 225/35 R18 All Comfort with up to 3 people ECO with up to 3 people With full load front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 200/2.0 (29) 240/2.4 (35) 260/2.6 (38) 320/3.2 (46) 260/2.6 (38) 320/3.2 (46) 200/2.0 (29) 260/2.6 (38) 260/2.6 (38) 320/3.2 (46) 260/2.
Customer information Customer information Customer information Customer information ................ 207 Vehicle data recording and pri‐ vacy ........................................... 207 This vehicle has systems that transmit and/or receive radio waves subject to Directive 1999/5/EC. These systems are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Copies of the original Declarations of Conformity can be obtained on our website.
208 Customer information ■ Vehicle reactions in particular driving situations (e.g. inflation of an airbag, activation of the stability regulation system) ■ Environmental conditions (e.g. temperature) These data are exclusively technical and help identifying and correcting errors as well as optimizing vehicle functions. Motion profiles indicating travelled routes cannot be created with these data. If services are used (e.g.
Customer information 209
210 Index A Accessories and vehicle modifications .......................... 149 Adjustable air vents ................... 116 Airbag and belt tensioners ........... 82 Airbag deactivation ................ 42, 82 Airbag system .............................. 37 Air conditioning regular operation ................................ 117 Air conditioning system .............. 110 Air intake .................................... 117 Air vents...................................... 116 Antilock brake system ........
211 Cupholders .................................. 49 Curtain airbag system .................. 41 D Danger, Warnings and Cautions . . . 4 Daytime running lights ............... 103 Declaration of conformity............ 207 Door open .................................... 86 Doors............................................ 22 Driver assistance systems.......... 129 Driver Information Centre............. 86 Driving hints................................ 118 E Electric adjustment ......................
212 M Instrument panel fuse box ......... 167 Instrument panel illumination ..... 163 Instrument panel illumination control .................................... 105 Instrument panel overview ........... 10 Interior care ............................... 192 Interior lighting............................ 105 Interior lights ...................... 105, 163 Interior mirrors.............................. 26 Introduction .................................... 3 ISOFIX child restraint systems ....
213 Service ....................................... 117 Service display ............................ 78 Service information .................... 193 Service vehicle soon .................... 83 Side airbag system ...................... 40 Side blind spot alert.................... 141 Sidelights.................................... 101 Side turn signal lights ................ 162 Spare wheel ............................... 182 Speed limiter............................... 130 Speedometer ......................
214
