Owner`s manual

Remote-Control Equivalent Commands & Messages:
Pressing buttons on Vaux remote controls or keypads initiates actions equivalent to the following VauxProtocol Commands. Since
these actions result in the same Messages being sent (as they would for the equivalent Command), the control system must only parse
one set of Messages. This means that the control system is always up-to-date on zone-routes, volume-levels, and other system
parameters, regardless of whether they were initiated by a VauxProtocol command, or by a remote-control button press.
Remote-Control Button-Press Equivalent Command Status-Message
Set-Switcher-Base-Zone (prog/hold-#-#) *PW,100,0,0,0,bzn <cr> !C,100,0,0,0,bzn <cr>
(## = bzn: 01 to 98)
Source-Select (tuner…) or Zone-Off *CW,13,zon,src <cr> !S,3,zon,sta,stv,ssa,ssv,vvl,vvr,bas,trb <cr>
Volume-Up/Down/Release (note 1) *CW,35/36/37,zon <cr> !S,20,zon,sta,vvl,vvr <cr> (when button released)
Bass-Up/Down (shift-chan-up/dn) *CW,42/43,zon <cr> !S,40,zon,bas,trb <cr>
Treble-Up/Down (shift-vol-up/dn) *CW,44/45,zon <cr> !S,40,zon,bas,trb <cr>
Flat (shift-rewind) *CW,41,zon <cr> !S,40,zon,bas,trb <cr>
Mute-Toggle (mute) *CW,50,zon <cr> !S,20,zon,sta,vvl,vvr <cr>
Mute-On (shift-mute) *CW,51,zon <cr> !S,20,zon,sta,vvl,vvr <cr>
Mute-Off (shift-a/b) *CW,52,zon <cr> !S,20,zon,sta,vvl,vvr <cr>
Clusters (note 2) – messages are sent for each zone in cluster-group:
Cluster-Source-Select (tuner…) or Off *CW,60,gbz,gzd,src,src <cr> !S,3,zon,sta,stv,ssa,ssv,vvl,vvr,bas,trb <cr>
Cluster-Vol-Up/Down *CW,62/63,zon <cr> !S,20,zon,sta,vvl,vvr <cr>
Cluster-Mute-Toggle/On/Off *CW,50/51/52,zon <cr> !S,20,zon,sta,vvl,vvr <cr>
Source-Trim-Down (shift-down) *PW,22,src,240 <cr> !C,22,src,ast <cr>
Source-Trim-Up (shift-up) *PW,22,src,241 <cr> !C,22,src,ast <cr>
Zone-Setup (shift-pause-#) *PW,40,zon,# <cr> !C,9,zon,vll,vhh,vil,vir,vmm,mod,bas,trb,tud,tdd <cr>
Initial-Vol-to-Current (shift-ffwd) *PW,40,zon,1 <cr> !C,9,zon,vll,vhh,vil,vir,vmm,mod,bas,trb,tud,tdd <cr>
Restore-All-Factory-Setttings *PW,254,0,0,1 <cr> !C,254,0,0 <cr>
(prog/hold-9-9)
Note 1 – Volume adjustment:
Volume ramps at 2-dB/100-msec until button released, or Min/Max-Vol reached!
Note 2 – Clusters:
Clusters 1 to 8 accessed by setting remote to zones 91 to 98, respectively.
Clusters must be programmed to define gbz and gzd for each cluster.
Note 3 – Zone-Setup Command:
These Setup commands are handy for configuring zones, and are identical to the setup commands described in the previous
section. The zone must be on and not muted to use these commands
sid = 1 Set Zone-Initial-Volumes to current left/right levels
sid = 2 Set Zone-Mute-Volume to current (left) level
sid = 3 Set Zone-Min-Volume to current (left) level
sid = 4 Set Zone-Max-Volume to current (left) level
sid = 5 Set Previous-Volume-Flag Off (zone turns on with programmed Initial-Volume level) (normal)
sid = 6 Set Previous-Volume-Flag On (zone turns on at previous level, saved when last turned off)
sid = 7 Set Audio-Mode to Mono
sid = 8 Set Audio-Mode to Stereo (normal)
sid = 9 Restore Zone-Factory-Settings (restored on this one zone only)
Lattis Matrix Switcher 43 Software Version 7.3.0.0