User manual
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Starting up
- 6 Connections and operating elements
- 7 Operating
- 7.1 Starting the device
- 7.2 Navigating the menu
- 7.3 Operating on the unit
- 7.3.1 Setting the DMX address
- 7.3.2 Setting the DMX mode
- 7.3.3 ‘Automatic mode’
- 7.3.4 Operating mode ‘Sound control’
- 7.3.5 Master / slave mode
- 7.3.6 Setting colour macro
- 7.3.7 Setting dimmer and strobe effect for CW LEDs (WhiteBar)
- 7.3.8 Setting an individual mixed colour
- 7.3.9 Rotating the Display
- 7.3.10 Display lighting
- 7.3.11 Behaviour on DMX control failure
- 7.3.12 Dimmer curve
- 7.3.13 Key lock
- 7.3.14 Resetting the device to factory defaults
- 7.3.15 PWM (pulse width modulation)
- 7.3.16 Firmware version display
- 7.3.17 Operating hours display
- 7.3.18 LED temperature display
- 7.4 Menu overview
- 7.5 Functions in 3-channel mode
- 7.6 Functions in 6-channel mode
- 7.7 Functions in 12-channel mode
- 7.8 Functions in 16-channel mode
- 7.9 Functions in 56-channel mode
- 7.10 Functions in 68-channel mode
- 8 Technical specifications
- 9 Plug and connection assignment
- 10 Troubleshooting
- 11 Cleaning
- 12 Protecting the environment
2 Safety instructions
This device is intended for use as an electronic lighting eect by means of LED tech‐
nology. The device is designed for professional use only and is not suitable for use in
households. Use the device only as described in this user manual. Any other use or
use under other operating conditions is considered to be improper and may result in
personal injury or property damage. No liability will be assumed for damages
resulting from improper use.
This device may be used only by persons with sucient physical, sensorial, and intel‐
lectual abilities and having corresponding knowledge and experience. Other persons
may use this device only if they are supervised or instructed by a person who is
responsible for their safety.
Extend the operating life of the device by regular breaks and by avoiding
frequent switching on and o. The device is not suitable for continuous
operation.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking
hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces
and choke! Never let children unattended use electrical devices.
DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable
parts inside. Do not use the device if covers, protectors or optical components are missing or damaged.
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a protective contact plug. Do not modify the mains
cable or the plug. Failure to do so could result in electric shock/death or re. If in doubt, seek advice from a registered electrician.
WARNING!
Eye damage caused by high light intensity
Never look directly into the light source.
WARNING!
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights.
NOTICE!
Risk of re
Do not block areas of ventilation. Do not install the device near any direct heat source. Keep the device away from naked ames.
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid
direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions specied in the chapter
‘Technical specications’ of this user manual. Avoid heavy temperature uctuations and do not switch the device on immediately
after it was exposed to temperature uctuations (for example after transport at low outside temperatures). Dust and dirt inside
can damage the unit. When operated in harmful ambient conditions (dust, smoke, nicotine, fog, etc.), the unit should be main‐
tained by qualied service personnel at regular intervals to prevent overheating and other malfunction.
Intended use
Safety instructions
Colors NerveStrobe HP
7
Stroboscope