User manual
Table Of Contents
- Table of contents
- 1 General information
- 2 Safety instructions
- 3 Features
- 4 Installation
- 5 Starting up
- 6 Connections and operating elements
- 7 Operating
- 7.1 Starting the device
- 7.2 Navigating the menu
- 7.3 Operating on the unit
- 7.3.1 Setting the DMX address
- 7.3.2 Setting the DMX mode
- 7.3.3 ‘Automatic mode’
- 7.3.4 Operating mode ‘Sound control’
- 7.3.5 Master / slave mode
- 7.3.6 Setting colour macro
- 7.3.7 Setting dimmer and strobe effect for CW LEDs (WhiteBar)
- 7.3.8 Setting an individual mixed colour
- 7.3.9 Rotating the Display
- 7.3.10 Display lighting
- 7.3.11 Behaviour on DMX control failure
- 7.3.12 Dimmer curve
- 7.3.13 Key lock
- 7.3.14 Resetting the device to factory defaults
- 7.3.15 PWM (pulse width modulation)
- 7.3.16 Firmware version display
- 7.3.17 Operating hours display
- 7.3.18 LED temperature display
- 7.4 Menu overview
- 7.5 Functions in 3-channel mode
- 7.6 Functions in 6-channel mode
- 7.7 Functions in 12-channel mode
- 7.8 Functions in 16-channel mode
- 7.9 Functions in 56-channel mode
- 7.10 Functions in 68-channel mode
- 8 Technical specifications
- 9 Plug and connection assignment
- 10 Troubleshooting
- 11 Cleaning
- 12 Protecting the environment
7.3.8 Setting an individual mixed colour
1.
Press to activate the main menu.
2.
Press or repeatedly until the display shows ‘Stand Alone’ . Conrm with .
3.
Press or repeatedly until the display shows ‘Manual’ . Conrm with .
4.
Press or to select the desired submenu or the desired value.
The following sub menus are available:
Menu level 3 Menu level 4 Description
‘Dimmer’ ‘000…255’ Dimmer intensity
‘Strobe’ ‘AC 0 … 30Hz’ Strobe eect frequency from slow to fast
‘Red’ ‘000…255’ Intensity red from 0 % to 100 %
‘Green’ ‘000…255’ Intensity green from 0 % to 100 %
‘Blue’ ‘000…255’ Intensity blue from 0 % to 100 %
‘White’ ‘000…255’ Intensity white from 0 % to 100 %
‘WhiteBar’ ‘000…255’ Intensity WhiteBar from 0 % to 100 %
5.
Press to accept the selection.
7.3.9 Rotating the Display
1.
Press to activate the main menu.
2.
Press or repeatedly until the display shows ‘Settings’ . Conrm with .
3.
Press or repeatedly until the display shows ‘Display Reverse’ . Conrm with
.
4.
Use or to choose between ‘On’ (display rotated by 180°) or ‘O’ (display
not rotated).
5.
Press to accept the selection.
7.3.10 Display lighting
1.
Press to activate the main menu.
2.
Press or repeatedly until the display shows ‘Settings’ . Conrm with .
3.
Press or repeatedly until the display shows ‘Display Backlight’ . Conrm
with .
4.
Use or to choose between ‘On’ (display permanently on) or ‘O’ (display
turns o after a few seconds in case of inactivity).
5.
Press to accept the selection.
7.3.11 Behaviour on DMX control failure
1.
Press to activate the main menu.
2.
Press or repeatedly until the display shows ‘Settings’ . Conrm with .
3.
Press or repeatedly until the display shows ‘DMX Fail’ . Conrm with .
Operating
Colors NerveStrobe HP
17
Stroboscope