Solutions for Demanding Applications VarTech Systems Inc. Industrial Flat Panel Displays VT190 DiamondVue/CrystalVue Series 19.
Read these instructions completely before attempting to operate your new LCD Color Display. Table Of Contents Page Section 1 Page Section 4 Introduction 3 Touch screen 10 1.1 VT190 Series Features 3 4.1 Touch Screen Introduction 10 1.2 Product Safety Precautions 3 4.2 Touch Screen Installation 10 Section 2 Section 5 Display Setup 4 2.1 Inspection 4 2.2 Unpacking 4 Section 6 2.3 Included Parts 4 6.1 Cleaning & Maintenance 2.4 Connecting The Display 4 2.
INTRODUCTION SECTION 1 1.1 VT190 Series Features The VT190 Series is capable of displaying 16.8M colors in a continuous spectrum. The VT190 Series provides a standard VGA input, a DVI-I input, an S-Video input, and a Composite input. The VT190 Series is auto synchronous adjusting the display to the appropriate VGA input. The VT190 Series is available in Chassis Mount, Panel Mount, Wall Mount, and Rack Mount configurations.
DISPLAY SETUP SECTION 2 2.1 Inspection of your VT190 display The VT190 is supplied with different accessories depending on the model configuration purchased. Verify the VT190 and accessories are what were ordered. Contact your Vartech salesperson should there be any discrepancies. 2.2 Unpacking and setting up your VT190 display Your LCD monitor package will consist of the components listed below. Open shipping container and place all the components on a flat clean surface. 2.
2.5 Input Video Connections The VT190 Series provides four industry standard video inputs: Analog RGB (VGA) with auto detect of Digital Separate Sync, Sync-On-Green, and Composite Sync. Auto detects from VGA to UXGA, interlaced and non-interlaced video. DVI-D with auto detect of Digital Separate Sync. S-Video for 4 wire video Composite for NTSC, PAL, and SECAM video (interlaced) Optional BNC Adaptor Cable A HD15 (VGA)-to-5xBNC adapter cable is available.
GETTING STARTED SECTION 3 3.
3.
Main Source : Select the input video signal VGA 1 / Composite Video / S-Video / VGA 2 / DVI / HD/SD Component Utilities : Setup # Auto Picture Setup : Auto adjust the image position, phase and size # Auto Color Gain : Auto Color Calibration (Function in ARGB mode ONLY – See appendix IV) # Manual Clock : Adjust the image horizontal size # Manual Phase : Fine tune the data sampling position (adjust image quality) Auto Source Seek : OFF / ON ON – Auto source select always enable OFF – Disa
Color Temperature Color Temp : 9300K / 8000K / 6500K / 5000K Red : Green : Blue : Hot Key Hot key 1 : Brightness / Contrast / Input / Aspect / Volume Hot key 2 : Brightness / Contrast / Input / Aspect / Volume Reset to Factory Defaults Factory Defaults Reset Color Gain # DDC Updates ** : FUNCTION IN VIDEO MODE ONLY # : DISPLAY AND FUNCTION IN VGA MODE ONLY Exit the OSD menu to save the setting chosen 9 VT190 DiamondVue/CrystalVue User’s Guide 150‐180
TOUCHSCREEN SECTION 4 4.1 Introduction Touch screens are a common means to interface operator inputs to a system. The universal standard of Windows GUI (Graphical User Interface) has significantly increased the use of touch screens. There are five main touch technologies. The technologies are resistive, surface acoustic wave (SAW), capacitive, infrared (IR), and projective capacitive. Each touch technology has advantages and disadvantages based on different user applications. 4.
TROUBLESHOOTING SECTION 5 5.
MAINTENANCE SECTION 6 6.1 Cleaning Occasionally clean the display panel and cabinet with a soft cloth dampened (not soaked) with a mild (non-abrasive) glass cleaner. Keep turning a fresh side of the cloth toward the screen surface to avoid scratching it with accumulated grit. Note: The solvent should be applied only to the cloth, and not directly on the monitor screen. Do not use paper products as they may scratch the surface. To minimize the risk of abrasion, allow the screen to stand dry.
MOUNTING INSTRUCTIONS SECTION 7 7.1 Panel Mount Procedure Mechanical Drawings Model VT190P2 VT190C2 VT190W2 VT190R2 VT190PSS VT190M2 Description 19" DiamondVue/CrystalVue Panel Mount Drawing (Nema 4) 19" DiamondVue/CrystalVue Open Frame Drawing 19” DiamondVue/CrystalVue Wall/Vesa Mount Drawing 19” DiamondVue/CrystalVue Rack Mount Drawing 19” DiamondVue/CrystalVue Panel Mount SS Drawing (Nema 4x) 19” DiamondVue/CrystalVue Table Top Drawing Page(s) 16, 17 18, 19 20 21 22‐23 24 1.
SPECIFICATIONS ENGINEERING SPECIFICATIONS – DiamondVue Panel Size 19.0” (48.26cm) Type Active Matrix Color Thin Film Transistor (TFT) Native Panel Resolution SXGA Pixel Format 1280x3 RGB (H) x 1024 (V) Pixel Pitch 0.294 per one triad (H) x 0.294 (V) mm Pixel Arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe Active Display Area 14.816” x 11.853” 376.320mm x 301.056mm Viewing Angle (Left/Right) 89/89o (typ.) Viewing Angle (Up/Down) 89/89o (typ.
SPECIFICATIONS ENGINEERING SPECIFICATIONS – CrystalVue Panel Size 19.0” (48.26cm) Type Active Matrix Color Thin Film Transistor (TFT) Native Panel Resolution SXGA Pixel Format 1280x3 RGB (H) x 1024 (V) Pixel Pitch 0.294 per one triad (H) x 0.294 (V) mm Pixel Arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe Active Display Area 14.816” x 11.853” 376.320mm x 301.056mm Viewing Angle (Left/Right) 89/89o (typ.) Viewing Angle (Up/Down) 89/89o (typ.
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VT190 DiamondVue/CrystalVue User’s Guide 150‐180
VARTECH SYSTEMS INC. HEADQUARTERS 6399 Amp Drive, Clemmons, NC 27012 Toll-Free: 800.223.8050 International Phone: 001.225.298.0300 Fax: 225.297.2440 E-mail: sales@vartechsystems.com www.vartechsystems.com 01.11.
