Solutions for Demanding Applications VarTech Systems Inc. Industrial Flat Panel Displays VT121 DiamondVue/CrystalVue Series 12.
User’s Guide Read these instructions completely before attempting to operate your new Color Display. Table Of Contents Page Section 1 Page Section 4 Introduction 3 Touch screen 12 1.1 About LCD Monitors 3 4.1 Touch Screen Introduction 12 1.2 Product Safety Precautions 4 4.2 Touch Screen Installation 12 Section 2 Section 5 Display Setup 4 2.1 Display Features 4 2.2 Unpacking The Display 4 Section 6 2.3 Included Parts 5 6.1 Cleaning & Maintenance 2.4 Connecting Your Display 5 2.
INTRODUCTION SECTION 1 1.1 About LCD Monitors A liquid crystal display (LCD) is a thin, flat panel used for electronically displaying information such as text, images, and moving pictures. Among its major features are its lightweight construction, its portability, and its ability to be produced in much larger screen sizes than are practical for the construction of cathode ray tube (CRT) display technology. Its low electrical power consumption enables it to be used in battery-powered electronic equipment.
1.2 Product Safety Precautions Ensure that sufficient space is available around the display to provide the circulation necessary for cooling. Ensure that the ambient air temperature will not exceed the specified maximum temperature. Do not attempt to service this display yourself. The rear chassis has a seal so that non qualified personnel will not expose themselves to dangerous voltages or other risks. To protect from electrical shock, unplug the display power supply from the wall before moving.
2.3 What is included with your display VT121P-2 LCD Monitor 5 ft Video Cable. A 120VAC power connection. 10-32 Mounting Hardware. (For use with Panel Mount only) 6 ft RS232 Touch Interface Cable (Optional when touch is installed) CD ROM with Touch Screen Drivers (Optional when touch is installed) Users Manual 2.4 1 2 3 4 5 Connecting the Display Connect all cables to the computer first. This would include the VGA cable and the optional RS 232 serial or usb touch screen connection.
Note: The following figure is the view looking into the pin end of the male connector or solder terminal end of the female connector. Standard Resolution Supported ⇒ 800 x 600 (VGA) Composite Video Input Connector: CVBS 1.0V p-p S-Video: S-VHS LUMA Signal Input 0.7V p-p CHROMA Signal Input 0.7V p-p Pin assignments for the HD15 video connector.
2.5 Signal Connections Cont. Optional BNC Adaptor Cable A 5BNC-to-HD15 adapter cable is available. The functions of the cables are described below. R, B, and G: Red, Green, and Blue input connectors to establish color. These are used for RS-343 analog signals. HS/CS: Separate horizontal/composite sync signal from the video source. VS: Separate vertical sync signal from the video source.
SECTION 3 3.1 Adjusting the display NOTE: By way of explanation the following refers to a set of sample buttons that may be obtained as an option.
- - decrease the setting / moves the selector to the - - Press and hold SEL DN Press and hold SEL DN button to power on the button to power on the controller controller Press and hold MENU Press and hold MENU button for 15 seconds to button for 15 seconds to enable / disable lock of the enable / disable lock of OSD menu the OSD menu + + previous function (under OSD menu on state) Load factory default Lock OSD menu (Function with signal input only) Switch to next input source (under OSD
Exit Exit the OSD menu and save the settings Autosetup Auto adjust the positions, phase, frequency Yes No Frequency Adjust the image horizontal size Phase Image Horizontal Fine tune the data sampling position (adjust image quality) Use +/- to move the image Position Image Vertical horizontally Press – or + (-+ ) Use +/- to move the image vertically Press – or + (-+ ) Position# Position Exit Exit the OSD menu Utilities OSD setting 4 OSD Timeout : 0 / 10 / 20 / 30 / 40 / 50 / 60 seconds (Always
SECTION 4 TOUCHSCREEN 4.1 Introduction Touch screens are a common means to interface operator inputs to a system. The universal standard of Windows GUI (Graphical User Interface) has significantly increased the use of touch screens. There are four main touch technologies. The technologies are resistive, surface acoustic wave (SAW), capacitive, and infrared (IR). Each touch technology has advantages and disadvantages based on different user applications. 4.
Image position: If it is impossible to position the image correctly, ie the image adjustment controls will not move the image far enough, then test using another graphics card. This situation can occur with a custom graphics card that is not close to standard timings or if something is in the graphics line that may be affecting the signal such as a signal splitter (please note that normally a signal splitter will not have any adverse effect).
Do not use paper products as they may scratch the surface. To minimize the risk of abrasion, allow the screen to stand dry. Special care should be taken when cleaning a touch screen or polycarbonate shield that is installed over the screen. Abrasive and certain chemical cleaners can easily damage the surface. Never use alcoholic or ammoniac cleaners to clean the polycarbonate shield or a touch screen.
top/bottom of the cutout in the panel. Extra lock nuts and washers are provided.
SPECIFICATIONS DIAMONDVUE ENGINEERING SPECIFICATIONS Panel Size Type Resolution Capabilities 12.1” Active Matrix Color Thin Film Transistor (TFT) VT121P2, VT121PSS2 SVGA, XGA Pixel Pitch SVGA 0.3075 (H) x 0.3075 (W) mm XGA 0.24 (H) x 0.24 (W) mm Active Display Area 9.69” x 7.28” 246mm x 185mm Pixel Format SVGA 800 (H) x 600 (W) XGA 1024 (H) x 768 (W) Viewing Angle (Left/Right) Viewing Angle (Up/Down) SVGA 80/80 deg. XGA 70/70 deg. SVGA 80/60 deg. XGA 45/55 deg.
Storage Humidity 10 to 95%NC Operating Altitude Up to 10,000 ft Storage Altitude Up to 40,000 ft Dimensions 15.0” (w) x 12.5” (h) 381mm x 317.5mm Cut Out Dimensions 13.7” (w) x 11.25” (h) 347.98mm x 285.75mm Weight 9.5 lbs (4.31) NEMA 4 12.0 lbs (5.
SPECIFICATIONS CRYSTALVUE ENGINEERING SPECIFICATIONS Panel Size Type Resolution Capabilities 12.1” Active Matrix Color Thin Film Transistor (TFT) VT121PHB2, VT121PSSHB SVGA, XGA Pixel Pitch SVGA 0.3075 (H) x 0.3075 (W) mm XGA 0.24 (H) x 0.24 (W) mm Active Display Area 9.69” x 7.28” 246mm x 185mm Pixel Format SVGA 800 (H) x 600 (W) XGA 1024 (H) x 768 (W) Viewing Angle (Left/Right) Viewing Angle (Up/Down) SVGA 80/80 deg. XGA 70/70 deg. SVGA 80/60 deg. XGA 45/55 deg.
Storage Altitude Up to 40,000 ft Dimensions 15.0” (w) x 12.5” (h) 381mm x 317.5mm Cut Out Dimensions 13.7” (w) x 11.25” (h) 347.98mm x 285.75mm Weight 9.5 lbs (4.31) NEMA 4 12.0 lbs (5.
VARTECH SYSTEMS INC. HEADQUARTERS 11529 Sun Belt Ct. Baton Rouge, Louisiana 70809 Toll-Free: 800.223.8050 International Phone: 001.225.298.0300 Fax: 225.297.2440 E-mail: sales@vartechsystems.com www.vartechsystems.com 2.8.
