VARMATEC RADIO OPERATING INSTRUCTIONS Warning! Before installing the VARMATEC RADIO, please read these instructions carefully 550 CПРОЕКТРИРОВАНО И СДЕЛАНО В ИТАЛИИ STAR PROGETTI RADIO ELECTRIC HEATERS MADE IN ITALY
ENGLISH 2 1 no.
Radio remote control unit code PTVTEL 15 CHANNELS -+ CHANNEL NO FUNCTION CHANNEL SELECTION PP REMOVE RADIO CONTROLS AND DETECTORS 1-12 HEATER MANAGEMENT 13 SELF-LEARNING 14 ENABLE / DISABLE 15 ST15 PIR DETECTOR TRANSMISSION SETTING POWER SWITCHING ON PIR DETECTOR* SWITCHING OFF • Degree of protection: IP20 • Battery: 3 V type CR2450 • Dimensions: 135*44*10 mm • Weight: 40 g • Operating frequency: 433 MHz • two-digit display screen • 15 channels • 5 buttons • Colour: white • Material: ABS
START After installing the heater (Fig.a) on the wall: Operate the main switch. Fig.1 The heater is now powered by 220-240Vac mains voltage. A green light flashes for a few seconds to confirm the operation.Fig. 2 ISTRUZIONI D’USO OPERATING INSTRUCTIONS MODE D’EMPLOI INSTRUCCIONES DE USO GEBRAUCHSANWEISUNGEN ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ Fig.a VARMA TANDEM RADIO -2000 Watt (cod. 550/20*R) - VARMA TANDEM IPX5 -1500 Watt (cod. 550/15) -2000 Watt (cod.
2 Take the radio remote control unit cod. PTVTEL: • Within 10 seconds use the "+" and "-" buttons to select the channel [1-12] selected for assignment. Example «channel 1» Fig.6 Immediately afterwards press the button as shown in Fig. 7. The blue LED on the heater goes out to confirm that the storage operation is complete. Fig.8 • • N.B. If programming does not work, repeat programming Fig.6 Fig.8 Fig.
OPERATION OF THE REMOTE CONTROL 1 CHANNEL 1….12 Switching ON Take the radio command code no. PTVTEL: • On channel «1», press the button as shown in fig. 9 • Red LED lights up Fig.10 MIN Fig.9 Fig.10 2 Setting power. Take the radio remote control unit cod. PTVTEL: On channel «1», press the button as shown in fig. 11 • • Yellow LED lights up Fig.12 medium power • On channel «1», press the button as shown in fig. 13 • Green LED lights up Fig.14 maximum power Fig.13 MED - MAX Fig.11 Fig.
OPERATION OF THE REMOTE CONTROL • 3 CHANNEL 14 NOT INCLUDED ACCESSORY COD.ST15 Enable PIR* from remote control Take the supplied radio control unit cod. PTVTEL • By using the "+" and "-" buttons select channel 14 Fig.15 and immediately after press the button as shown in Fig. 16 • The blue LED on the heater starts flashing twice to confirm the operation Fig.17 4 Disable PIR* from remote control Take the supplied radio control unit cod.
CLEARING THE HEATER MEMORY CANCELLAZIONE PIR CHANAEL PP REMOVE RADIO CONTROLS AND DETECTORS Take the radio remote control unit cod. PTVTEL: • By using the "+" and "-" buttons select channel PP Fig.19 and immediately after press the button as shown in Fig. 20 • The blue LED on the heater starts flashing to confirm the cancellation operation has been carried out Fig. 21 N.B. If deletion does not work, please repeat the operation. Fig.19 Fig.20 Fig.
TROUBLESHOOTING PROBLEM CAUSES The radio remote control • does not work The radio remote control works but does not control the heater Remote control does not store with heater SOLUTIONS Batteries are low • PTVTEL has not been stored with the heater Replace batteries Fig. 22 • Store PTVTEL read chapter «STORAGE OF 1 RADIO REMOTE CONTROL RADIO HEATER» • the heating damaged. Power control does not work • The controller damaged. element element Fig.
