The information furnished in this manual is for informational use only and is subject to change without notice. Please check www.vari-lite.com for latest version. Vari-Lite assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual. All information and graphics are property of Vari-Lite, a Philips group company, 10911 Petal Street Dallas, Texas 75238 USA.
FOREWORD How To Obtain Warranty Service A copy of the Vari-Lite Limited Warranty was included in the shipping package for this VARI❋LITE product. To obtain warranty service, please contact customer service at 1-877-VARI-LITE (1-877-827-4548) or +1-214-647-7880 or via e-mail at entertainment.service@philips.com request a Return Material Authorization (RMA) for warranty service.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Compliance Notice FCC This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a commercial environment.
FOREWORD Safety Notice It is extremely important to read ALL safety information and instructions provided in this manual and any accompanying documentation before installing and operating the products described herein. Heed all cautions and warnings during installation and use of this product. Safety symbols used throughout this manual are as follows: CAUTION advising of potential damage to product. WARNING advising of potential injury or death to persons.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST EXCESSIVE EXPOSURE TO UV RADIATION 1. Many VARI❋LITE luminaires use a lamp that produces UV radiation. DO NOT look directly at lamp. 2. It is hazardous to operate luminaires without lens or shield. Shields, lenses, or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired. For example, by cracks or deep scratches.
FOREWORD Sicherheitshinweise Es ist äußerst wichtig, ALLE Sicherheitsinformationen und -hinweise in diesem Handbuch und dem beiliegenden Informationsmaterial zu lesen, bevor Sie die hierin beschriebenen Produkte installieren bzw. bedienen. Halten Sie bei der Installation und dem Einsatz dieses Produkts alle Warnhinweise und Vorsichtsmaßnahmen ein. Folgende Sicherheitssymbole werden in diesem Handbuch verwendet: VORSICHT - weist auf möglichen Produktschaden hin.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL WARNUNG: HINWEISE ZUM SCHUTZ GEGEN ÜBERHÖHTE UV-STRAHLUNG 1. Viele VARI❋LITE-Scheinwerfer verwenden die Lampentyp, der UV-Strahlen abgibt. SCHAUEN SIE NICHT direkt in die Lampe. 2. Es ist gefährlich, Leuchten ohne Linsen oder Blenden zu bedienen. Blenden, Linsen oder Ultraviolettschirme müssen ausgetauscht werden, sofern deren Schutzwirkung durch sichtbare Beschädigung (z. B. Sprünge oder Schrammen) eingeschränkt ist.
FOREWORD Notes de sécurité Avant de procéder à l’installation des produits décrits dans ce guide et de les mettre en marche, il est extrêmement important de lire TOUS les renseignements et TOUTES les directives de sécurité contenues dans ce guide ainsi que toute documentation jointe. Tenir compte de tous les avertissements et suivre toutes les précautions pendant l’installation et l’utilisation de cet appareil.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE UNE EXPOSITION EXCESSIVE AUX RAYONS UV 1. Plusieurs luminaires VARI❋LITE utilisent une lampe qui produit des rayons UV. NE PAS fixer son regard sur la lampe. 2. L’utilisation des luminaires sans lentille ou blindage pose des risques.
FOREWORD Aviso sobre Seguridad Es muy importante leer TODA la información e instrucciones sobre seguridad que se indica en este manual así como en los documentos adjuntos antes de instalar y operar los productos descritos. Se debe prestar atención a todos los avisos y advertencias durante la instalación y uso de este producto. Los símbolos de seguridad usados en este manual son los siguientes: CUIDADO, indica posibles daños al producto. ADVERTENCIA, indica posibles lesiones o muerte a las personas.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL ADVERTENCIA: INSTRUCCIONES PARA PROTECCIÓN CONTINUA CONTRA LA EXPOSICIÓN EXCESIVA DE RADIACIÓN ULTRA VIOLETA 1. Muchas luminarias VARI❋LITE usan un tipo de lámpara que produce radiación UV. NO mire directamente a la lámpara. 2. Es peligroso operar luminarias sin lentes o protectores. Debe cambiar los protectores, lentes o pantallas ultravioletas si se aprecia que han sido dañadas, y que su efectividad pudiera estar deteriorada.
FOREWORD 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL xii 15 Feb ru ary 201 1 02 .9 665.
TABLE OF CONTENTS Table of Contents Introduction About This Manual ...................................................................................................... Text Conventions ......................................................................................................... Additional Documentation........................................................................................... Customer Service .....................................................................................
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Control Channel Functions ........................................................................................ DMX Data Display .................................................................................................... DMX Mapping Color Mixing.............................................................................................................. Rotating Gobo Wheel...........................................................................
INTRODUCTION : ABOUT THIS MANUAL Introduction About This Manual This manual provides necessary information regarding safety, installation, operation and routine maintenance for the VARI❋LITE VL1100CD Ellipsoidal Reflector Spotlight (ERS) luminaire. Familiarizing yourself with this information will help you to get the most out of your product. WARNING: It is important to read ALL accompanying safety and installation instructions to avoid damage to the product and potential injury to yourself or others.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Note: Performing maintenance procedures may void the product warranty. Refer to the Vari-Lite Limited Warranty card included in the product shipping package for more information. For more information regarding DMX512 systems, refer to the following document available from United States Institute for Theatre Technology, Inc.
CHAPTER 1. Description This chapter contains descriptions of luminaire features and components, along with a list of accessories which are available. • Features • Components • Accessories 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Features Standard Features VL1100CD Ellipsoidal Reflector Spotlight (ERS) luminaires have the following standard features: • 315W ceramic discharge, long-life lamp. • Automated zoom optics system. • Crossfading CYM color system. All motors utilize a noise reducing, 50kHz. drive system that quiets operation during movement and also while static.
DESCRIPTION : COMPONENTS 1 Components Included Items The following illustration shows the included components for all models. Included Items Warranty Card Product Support Sheet VL1100 CD ROM (User’s Manual) Unpack & Quick Start Guide Product Registration 315W CDM Lamp Neutrik PowerCon AC Input Connector VL1100CD Luminaire 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Luminaire Overview The following illustration shows the external luminaire components and controls. Base Provides hook mounting holes and safety cable connection. Input Panel Provides DMX In and Thru, and AC Power connections. Power Input Connector Latch Gel, Silk or Frost Accepts frames or top hats Accessory Frame Yoke Leg (Control) Contains main control PCB and display PCB.
DESCRIPTION : ACCESSORIES 1 Accessories VL1100CD ERS Replacement Items/Accessories The following optional and/or replacement items can be ordered directly from Vari-Lite. (Please order by Vari-Lite part number.) VARI-LITE P/N ACCESSORY 22.9620.0194 Safety Cable Assembly 25.9661.0056 DMX Loopback Connector Assembly 25.9661.0057 DMX Terminator, 120 Ohm 28.8500.0054 USB Luminaire Programming Kit (Includes USB Upload Cable, Programming Kit CD ROM, Carry Bag, and Instructions)* 52.6541.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Notes 8 15 Feb ru ary 201 1 02 .9 665.
CHAPTER 2. Installation This chapter contains instructions for installation of all version of the VL1100CD ERS Luminaire. It includes connecting power and data, along with instructions for powering up the luminaire for the first time and addressing it within your system. • Power and Data Cabling Requirements • Installation Procedures • Powering Up • Addressing 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Power and Data Cabling Requirements AC Power WARNING: Do not power a VL1100CD ERS Luminaire from a dimmed circuit - even in "NonDim" mode. Dimmer and non-dim modules are not suitable sources of power because their output modifies the AC wave form. This may work for a short time, but will eventually result in power problems, luminaire mis-operation and/or failure.
2 INSTALLATION : POWER AND DATA CABLING REQUIREMENTS Data Cables The luminaire is equipped with two, 5-pin XLR connectors for DATA IN and DATA THRU (out) applications. DATA IN requires a 5-pin, female XLR connector and DATA THRU requires a 5-pin, male XLR connector. When purchasing or constructing data cables, it is important that not only the correct cable type be used, but also quality cable to ensure a reliable DMX512 system.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Recommended Cable Types/Manufacturers These are only a few of the suitable cable types. Any quality EIA485, twisted pair, 120 ohm, shielded cable will also work.
2 INSTALLATION : POWER AND DATA CABLING REQUIREMENTS DMX Termination Connector A male XLR DMX termination connector is required at the last luminaire (or "far end of the line") to prevent signal reflections. Signal reflections may cancel out the signal at certain line lengths, resulting in errors. The terminator is also necessary for software downloads and running tests on multiple luminaires. To construct your own connector, you will need the following components: • 5-pin, male XLR connector.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Installation Procedures Installing Lamp In the event the lamp was packed separately during shipment, it will be necessary to install before use. WARNING: Ensure that power is completely removed from luminaire when installing lamp. CAUTION: Wear cotton gloves or other covering while installing lamp. Touching lamp glass with bare fingers will leave oil and may cause the lamp to explode or reduce lamp life.
INSTALLATION : INSTALLATION PROCEDURES Step 2 3. Grip lamp by base and firmly install in socket. Do not touch lamp CAUTION: with bare fingers. Socket Lamp Install lamp, firmly pressing into place. Figure 2-3: Installing VL1100CD Lamp in Socket Step 4. Re-install backcap, ensuring that alignment studs and holes are aligned (Figure 2-2). Step 5. Align lamp. (Refer to “Align Lamp For Maximum Beam Irradiance” on page 23.) 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Accessory Frame Holder An accessory frame holder is provided for the addition of a top hat or gel frame with silks, frosts or color correction if required. The frame holder is designed to fit a standard 7.5-inch gel frame or top hat. To remove and replace frame or top hat: Step 1. Disconnect luminaire AC input cable from power source. Step 2. At front lens, press upward on accessory frame latch and turn to open. Step 3.
INSTALLATION : INSTALLATION PROCEDURES 2 Hanging the Luminaire The luminaire can be hung horizontally or vertically from any structure designed to work with the type of load created by this moving luminaire. The pan tube base provides two mounting holes for attaching truss hooks or other mounting hardware as required. Many compatible truss hooks are available from different manufacturers for your particular needs.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL To hang luminaire in truss: Step 1. Lift luminaire into mounting position. Step 2. Secure in place with truss hooks. Ensure truss hook hardware that locks hook in place (e.g. wing bolt) is properly tightened and that luminaire is fully supported. Step 3. Attach safety cable (sold separately) as follows: a. Connect end of cable to mounting pin at one side of pan tube base. b. Loop at least once around pipe and attach other end at second mounting pin.
INSTALLATION : INSTALLATION PROCEDURES 2 Connecting Data and Power A maximum of 32 luminaires may be connected in any one DMX data link. Note: This maximum limit applies to the luminaire "daisy chain" only. Your system or console may require fewer luminaires on a single data link path. Consult your console documentation for more information. To connect power and data: Step 1. After luminaire(s) are installed, connect data cable from console to first luminaire in chain at DATA IN connector. Step 2.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Powering Up Power-Up and Configuration Overview First Power-Up When powering up a VL1100CD ERS Luminaire for the first time, the lamp type and shutter settings must be configured. This procedure will usually happen prior to delivery. However, in the event that it has not been done or if the Main Controller Board has been replaced, it will be necessary.
INSTALLATION : POWERING UP 2 Standard Power Up Procedure Use this procedure when powering up a luminaire that has already been configured. (Refer to “PowerUp and Configuration Overview” on page 20.) Note: Refer to Chapter 4: Menu System for detailed instructions on menu functions. CAUTION: Before applying power, be sure the luminaire is hung or positioned so that the head and yoke can move freely without restriction. To power up luminaire: Step 1.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Power Up and Configuration Procedure Use this procedure when powering up a luminaire that has not been previously configured. (Refer to “Power-Up and Configuration Overview” on page 20.) Note: Refer to Chapter 4: Menu System for detailed instructions on menu functions. CAUTION: Before applying power, be sure the luminaire is hung or positioned so that the head and yoke can move freely without restriction. To configure luminaire at power up: Step 1.
INSTALLATION : POWERING UP 2 Align Lamp For Maximum Beam Irradiance After a new lamp is installed in the luminaire, it will be necessary to align the lamp to optimize the beam. WARNING: Backcap and adjustment screws will be HOT during lamp operation. Wear gloves and/ or use tools to prevent burns. To align lamp: Step 1. Set intensity to 100%. Step 2. Position beam on a white wall at a distance of 10 to 20 feet. Step 3.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Addressing Program Starting Address The DMX starting address is entered using the Menu Display. This address will be retained even if the power is removed. Note: Refer to Chapter 4: Menu System for detailed instructions on menu functions. Note: Refer to your console operating instructions for specific information regarding its addressing requirements. To program a DMX starting address: Step 1. Press [Menu]. Step 2.
CHAPTER 3. Operation This chapter contains instructions for operating the luminaire using DMX control and for updating the internal software. • DMX Operation • DMX Mapping • Luminaire Timing • Updating Software 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL DMX Operation Channel Mapping These tables assume a DMX start address of 1. When a different starting address is used, this address becomes channel 1 function and other functions follow in sequence. (There is only one DMX mode for this luminaire, which is Enhanced 16-bit Mode.
OPERATION : DMX OPERATION 3 Table 3-2: Enhanced 16-Bit Mode - VL1100CD Shutter (S) Models DMX Channel Parameter Range 1 Dimmer * 0-255 2 Hi Byte Pan 0-65535 3 Lo Byte Pan 0-65535 4 Hi Byte Tilt 0-65535 5 Lo Byte Tilt 0-65535 6 Edge 0-255 7 Zoom 0 (small) - 255 (big) 8 Diffusion 0 (open) - 255 (diffused) 9 Blue 0 (open) - 255 (full saturation) 10 Amber 0 (open) - 255 (full saturation) 11 Magenta 0 (open) - 255 (full saturation) 12 Rotating Gobo 0-127 index 128-255 rota
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Control Channel Functions Control channel functions allow special actions such as reset, lamp on/off and partial recalibration. These must be executed with zero time transition or with timing disabled. Discrete values must be used; not manual controls such as faders or encoders (see chart below for values). Reset - resets all luminaire mechanisms. Lamp On or Lamp Off - switches lamp on or off.
OPERATION : DMX OPERATION 3 DMX Data Display The DMX data display shows the data received for the given luminaire and does not show the entire stream of 512 bytes. It shows only the number of channels used for the given luminaire model in 16bit enhanced mode. For example, a VL1100CD (shutter model) luminaire with an address of 40 will show DMX Channels 1-27 which would correlate to DMX Channels 40-66. 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL DMX Mapping Color Mixing The color mixing mechanism is a CYM subtractive color mixing system made up of a graduated color system for cyan, yellow, and magenta.
OPERATION : DMX MAPPING 3 Rotating Gobo Wheel Note: Gobos are sold separately. Contact your Authorized VARI❋LITE Dealer or visit the Vari-Lite web site, www.vari-lite.com, for available gobo patterns. The function operates in two modes: INDEX Mode and ROTATE Mode. The DMX values corresponding to these modes are as follows: • DMX values 0-127 will select each gobo in Indexing mode. • DMX values 128-255 will select each gobo in Rotating mode.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Shutter Mechanism For units with a shutter mechanism, the shutter is comprised of four frame blades that move independently or in unison. The entire assembly operates in a smooth, time-continuous motion using stepper motors (two per frame blade and one to rotate the entire shutter mechanism). The shutter mechanism can rotate 45o in either direction and the frame blades can tilt +/- 35o.
OPERATION : LUMINAIRE TIMING 3 Luminaire Timing Timing Channel Information Timing channel control improves the timed moves of certain groups of parameters. We provide three timing channels, one for Focus (Pan and Tilt), one for color parameters and one for beam parameters. Timing channels support time values of up to six minutes.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Note: Avoid changing timing channel values in a fading cue. This can cause unexpected behavior in the luminaire as the timing channel value is updated over time. Timing channel values and the final destination of the parameters affected by the timing channel should always be sent in a zero count.
OPERATION : LUMINAIRE TIMING 3 Table 3-11: VL1100CD Timing Channels Map % Value 14 15 16 17 18 19 20 21 22 23 24 = Seconds 34 6.8 35 7.0 36 7.2 37 7.4 38 7.6 39 7.8 40 8 41 8.2 42 8.4 43 8.6 44 8.8 45 9 46 9.2 47 9.4 48 9.6 49 9.8 50 10 51 10.2 52 10.4 53 10.6 54 11 55 11 56 12 57 12 58 13 59 13 60 14 61 14 62 14 63 15 25 64 15 65 16 26 66 16 67 16 27 28 29 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Table 3-11: VL1100CD Timing Channels Map % Value DMX = Seconds 30 76 20 77 20 78 21 79 21 80 21 31 81 22 32 82 22 83 23 33 84 23 85 23 34 35 36 24 24 88 25 89 25 90 25 91 26 92 26 93 27 94 27 95 27 96 28 38 97 28 98 29 39 99 29 100 29 37 40 41 42 43 101 30 102 30 103 30 104 31 105 31 106 32 107 32 108 32 109 33 110 33 111 34 112 34 113 34 114 35 45 115 35 116 36 46
OPERATION : LUMINAIRE TIMING 3 Table 3-11: VL1100CD Timing Channels Map % Value 47 48 49 50 = Seconds 118 36 119 37 120 37 121 38 122 38 123 38 124 39 125 39 126 39 127 40 128 40 129 41 130 41 131 41 132 42 52 133 42 134 43 53 135 43 136 43 51 54 55 56 57 137 44 138 44 139 45 140 45 141 45 142 46 143 46 144 47 145 47 146 47 147 48 58 148 48 149 49 59 150 49 151 49 60 61 62 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Table 3-11: VL1100CD Timing Channels Map % Value 63 64 = Seconds 160 53 161 53 162 54 163 54 164 54 165 55 65 166 55 167 56 66 168 56 169 56 67 68 69 70 71 170 57 171 57 172 58 173 58 174 58 175 59 176 59 177 59 178 60 179 60 180 65 181 65 182 65 183 70 72 184 70 185 75 73 186 75 187 75 74 75 76 77 38 DMX 188 80 189 80 190 85 191 85 192 85 193 90 194 90 195 95 196 95 197
OPERATION : LUMINAIRE TIMING 3 Table 3-11: VL1100CD Timing Channels Map % Value 80 81 82 83 = Seconds 202 110 203 120 204 120 205 120 206 130 207 130 208 140 209 140 210 140 211 150 212 150 213 160 214 160 215 160 216 170 85 217 170 218 180 86 219 180 220 180 84 87 88 89 90 221 190 222 190 223 200 224 200 225 200 226 210 227 210 228 210 229 220 230 220 231 230 232 230 233 230 234 240 92 235 240 236 250 93 237 250 238 250
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Table 3-11: VL1100CD Timing Channels Map % Value 96 97 = Seconds 244 280 245 280 246 290 247 290 248 290 249 300 98 250 300 251 310 99 252 310 253 310 100 40 DMX 254 310 255 Follows Cue Data 15 Feb ru ary 201 1 02 .9 665.
OPERATION : UPDATING SOFTWARE 3 Updating Software USB Download and Programming Luminaires You can upgrade Vari-Lite luminaire operating software using the USB Luminaire Programming Kit (Vari-Lite part number 28.8500.0054, sold separately) for desktop computers and newer laptops equipped with USB 2.0 ports. The USB Luminaire Programming Kit can be ordered directly from your Authorized VARI❋LITE Dealer. The VARI❋LITE USB Luminaire Programming Kit (28.8500.0054) includes: • VARI❋LITE USB Upload Cable (25.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Lists specific versions of downloaded software (on PC) Click to download specific software version to connected luminaire(s) Device Connection Status and USB Downloader Controls Click logo to go to Vari-Lite web site (internet connection required) Download History Will show current progress of download Figure 3-1: VL Download Program Window Transferring Software From Luminaire to Luminaire It is possible to transfer specific software versions between lum
OPERATION : UPDATING SOFTWARE 3 A termination connector is used in this process. Refer to page 10 for more information regarding the construction of this connector. Master luminaire containing software version to download Luminaire 1 requiring update Data Thru Luminaire 2 requiring update Data Thru DMX Termination Connector Loopback Connector Figure 3-2: Software Transfer Setup Transfer Procedure This procedure is used to transfer software versions between luminaires. Step 1.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Notes 44 15 Feb ru ary 201 1 02 .9 665.
CHAPTER 4. Menu System This chapter contains instructions for operating the luminaire using the Menu Display feature. • Menu Operation • Menu Functions • Self Tests 02.96 65.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Menu Operation What Is the Menu System? The menu system is a programmable set of commands used to configure, address, operate, and test the luminaire. The menu system is controlled at the Menu Display available at the yoke leg. The menu system has seven main functions which are referred to as “1st level.” Within these main functions, there can be up to four additional subfunctions (levels 2 thru 5), making five total levels.
MENU SYSTEM : MENU OPERATION 4 After 5 minutes of inactivity, the menu display will switch to its off state. Menu Shortcuts A few button combinations are provided as shortcuts for frequently used menu functions. These are as follows: • Lamp On - Press and hold [Up], then press [Enter]. (Arc and CD models only.) • Lamp Off - Press and hold [Down], then press [Enter]. (Arc and CD models only.) • Recalibrate - Press and hold [Up], then press [Menu]. • Interrupt Calibration - Press [Menu] at Power up.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Menu Functions Menu System Overview The following is a graphic representation of the entire menu system.
MENU SYSTEM : MENU FUNCTIONS 4 Menu System Function Chart 1st Level 2nd Level 3rd Level Address DMX DMX Address XXX Address value Setup LampType Arc 4th Level 5thLevel Incand CD Shutter? Yes No Config System Configuration LAMP Lamp Options (Arc & CD Models Only) Power Lamp Power ON (default) OFF Power Up Lamp Power-up State Lamp OFF Lamp Off Cal ON Lamp On After Calibration Lamp ON Lamp On (default) Pan/Tilt Pan and Tilt Options LampHour Lamp Hours Used XXXX Cumulative # of Operation
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL 1st Level Fixture Manual Manual Commands 50 2nd Level 3rd Level Status Status/Error Display Scrolls error messages or displays OK Re-Cal Recalibrate OK? Model Luminaire Model Type VL1100XX Model Type Lum Id Luminaire ID XXXXXXXX Luminaire ID Number Version Version XX/XX/XX MM/DD/YY (Page 1) Fixt Hrs Fixture Hours XXXX # Hours On Download OK? Pan Pan XXXX Data Tilt Tilt XXXX Data Dimmer Dimmer (Arc & CD Only) XXX Data Blue Blue XXX D
MENU SYSTEM : MENU FUNCTIONS 1st Level Test System Test 2nd Level ALL Test All Motors RUN TEST Run-Test in Progress Pan/Tilt RUN TEST Run-Test in Progress Dimmer (Arc Only) RUN TEST Run-Test in Progress Blue RUN TEST Run-Test in Progress Amber RUN TEST Run-Test in Progress Magenta RUN TEST Run-Test in Progress ColorMix Blue, Amber, Magenta test RUN TEST Run-Test in Progress Diffusn Diffusion Test RUN TEST Run-Test in Progress Rot Gobo Rotating Gobo Test RUN TEST Run-Test in Progress Edge
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Menu Function Definitions For easy reference, each possible menu item is listed alphabetically in the first column by its display abbreviation. The second column follows with a definition of the abbreviation and then a third column provides an explanation of its purpose and function. 52 Display Definition Purpose 10 Min 10 Minutes Sets Menu Display to automatically shut off after 10 minutes of non-use.
MENU SYSTEM : MENU FUNCTIONS Display Definition Inv Tilt Invert Tilt Reverses tilt action for special focus requirements. Lamp Lamp Accesses lamp power up options and information (Config). 4 Purpose Lamp 1 Lamp Specifies test lamp operation (Test). Lamp 2 Lamp Specifies test lamp operation (Test). Inserts magenta to 30%. Lamp OFF Lamp is Off Configures arc luminaire so that lamp will not strike upon power up.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL 54 Display Definition Purpose Version Version Displays current software version (Date and Time in two pages). Yes Yes Specifies that the luminaire contains the shutter accessory. Zoom Zoom Function Specifies zoom function for manual control (Manual) or for testing (Test). 15 Feb ru ary 201 1 02 .9 665.
MENU SYSTEM : SELF TESTS 4 Self Tests Running Parameter Tests The luminaire is capable of running self tests by using the TEST menu functions. Note: If a DMX data stream is present on the luminaire’s DMX input connector, Self Test and Manual control is overwritten by the DMX command protocol and neither (Self Test and Manual) will operate.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Movement Disable The Movement option allows pan and tilt to be disabled so that the luminaire can be placed in any position for testing without movement occurring. In order to regain full control of the luminaire, Movement will need to be enabled after testing. Note: When using the Movement option, pan and tilt will be disabled for all the luminaires that are linked. To set movement option: 56 Step 1. Press [Menu]. Step 2.
APPENDIX A. Troubleshooting and Maintenance This appendix provides instructions for troubleshooting and performing routine maintenance which may be necessary during the life of the luminaire. • Troubleshooting • Routine Maintenance WARNING: All routine maintenance procedures are to be performed with power completely removed from the luminaire. Never remove protective covers when luminaire is powered. Wear appropriate protective eye wear and gloves when servicing the fixture.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Troubleshooting Error Messages If a problem occurs during luminaire calibration, at the end of the calibration sequence the Menu Display will cycle through any applicable error message(s) until the end of the list is reached. To review the error messages again, it will be necessary to access them using the Status function. To access error messages: Step 1. Press [Menu]. Step 2. Press [Up] / [Down] arrows until Fixture appears. Press [Enter]. Step 3.
TROUBLESHOOTING AND MAINTENANCE A Troubleshooting Guide If a problem is suspected, first try recalibrating the luminaire to prompt an error message. Table A-2 below provides possible causes and remedies for various error messages and/or symptoms. CAUTION: Some troubleshooting is included for reference only. Performing remedies marked by gray areas will void product warranty. Refer to the Vari-Lite Limited Warranty card included with the product.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Routine Maintenance Cleaning Optical Lenses and Gobos WARNING: Remove power from luminaire before performing maintenance. The front lens and gobos may require cleaning after extended use. Use only isopropyl alcohol, along with a soft, lint-free cloth to clean glass components. To access gobos, refer to procedure below. Rotating Gobo Replacement WARNING: Remove power from luminaire before performing maintenance. Gobos may be HOT after operation.
TROUBLESHOOTING AND MAINTENANCE Step A 7. Re-install front cover. Inside Edge - orient toward center of wheel CAUTION: Rotate until open end of carrier is up Closed End Gear Open End Gobo MUST be oriented with the mirrored side towards the luminaire’s lamp. If not oriented properly, gobo will break. Be careful not to scratch gobo on side of carrier when installing.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Lamp Replacement For lamp replacement procedure, refer to “Installation Procedures” on page 14. 62 15 Feb ru ary 201 1 02 .9 665.
APPENDIX B. Technical Specifications Mechanical Zoom Optics Continuously variable field angle in imaging range from 19° to 36°, super zoom angles to 70° is programmable over a timed range of 2 seconds to 20 minutes. Color Mixing System A fully cross-fading CYM color system. All motors utilize a noise reducing, 50kHz. drive system that quiets operation during movement and also while static. Diffusion Field or gobo image can be continuously and smoothly diffused to wash.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Reflector Precision glass reflector with dichroic cold mirror coating. Operational Power Requirements 3 to 6 Amps depending upon input voltage. 100 - 240 VAC 50/60 Hz. Operational Temperature -20° to 122°F (-29° to 50°C) Cooling Free convection cooling when hung. Floor mounted units and extreme ambient temperatures activate a low-noise, forced-air cooling system. Control Compatible with a wide variety of DMX512 consoles.
TROUBLESHOOTING AND MAINTENANCE B Photometric VL1100CD ERS Luminaire - 315 CDM Lamp (All data taken with a seasoned light source at 20 hours of life.) FIELD ANGLE (degrees) FIELD DIAMETER TN* BEAM ANGLE (degrees) BEAM DIAMETER TN* CANDELA (cd) 19.0 .335 13.0 0.228 99,700 26.0 .462 19.5 0.344 44,400 36.0 .650 25.5 0.453 26,700 70.0 1.40 29.0 0.517 9,400 (Super Zoom) * Multiply throw distance by Tn to determine coverage.
VARI❋LITE - VL1100CD ERS LUMINAIRE USER’S MANUAL Notes 66 15 Feb ru ary 201 1 02 .9 665.
Vari-Lite 10911 Petal Street Dallas, Texas 75238 USA 1-877-VARI-LITE ❋ 1-214-647-7880 www.vari-lite.com. ©2011 Vari-Lite, a Philips group company. All Rights Reserved.
