Specification

TECHNICAL DATA
VAR-57
VARATHANE
®
SPAR VARNISH SPRAY
Form: GDH-867
Rev.: 060215
1
].DESCRIPTION AND USES .
Varathane
®
Spar Varnish Spray is designed to provide
maximum protection for all outdoor wood projects.
Varathane Spar Varnish is formulated to provide excellent
protection against sun, water, weather, sea spray and
chemicals. It features an advanced spray system that
allows you to spray at any angle, even upside down for
those hard to reach areas. A comfort tip reduces finger
fatigue caused by continuous spraying. It is ideal for all
types of outdoor projects, including outdoor furniture,
doors and window trim. It is not recommended for decks or
high traffic areas, siding or rough-sawn surfaces. This
product is not intended for interior surfaces with the
exception of window trim.
.PRODUCTS .
SKU Description
266327 11 ounce Gloss Spray
266328 11 ounce Semi-Gloss Spray
266330 11 ounce Satin Spray
.PRODUCT APPLICATION .
SURFACE PREPARATION
PREVIOUSLY FINISHED SURFACES – To ensure proper
adhesion, surfaces must be clean, dry and free of old
finishes, dust, dirt, oils or foreign matter. Old finishes in
poor condition must be removed. Sand the surface using
150-220 grit sandpaper. Sand to obtain a smooth surface.
Remove all sanding dust using a vacuum or tack cloth.
UNFINISHED SURFACE PREPARATION - Sand smooth
using 150-200 grit sandpaper and remove all sanding dust
with a vacuum or tack cloth. If a filler or putty is used,
make sure that it does not contain wax and allow enough
time for it to dry thoroughly.
STAINED OR PAINTED WOOD - Follow manufacturer’s
directions for application of stain or paint. Make certain the
surface is thoroughly dry before applying Varathane Spar
Varnish. Refer to the manufacturer’s label for dry times.
.
PRODUCT APPLICATION (cont.) .
SURFACE PREPARATION (cont.)
WARNING! If you scrape, sand, or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
APPLICATION
Use adequate ventilation at all times. Do not apply in
direct sunlight. Apply at temperatures between 55-90°F
(13-32°C) and the relative humidity is below 85%. Be
careful when applying over white or pastel paints or stains
as discoloration may occur. Test Varathane Polyurethane
in an inconspicuous area before beginning.
Shake the can vigorously before and during use. Use a
drop cloth or newspapers to protect surrounding areas
from spray mist. Apply light mist coats, holding can 10-12”
from the surface and spray with a smooth sweeping
motion to avoid runs and sags. Several light coats
provides for a better finish than one heavy coat. For hard
to reach areas, turn the can upside down to spray. Allow
the finish to dry, then recoat. Dries to the touch in 1 hour
and can be recoated after 2 hours. Let dry overnight
before use. To ensure a smooth finish, sand lightly
between coats using 220 grit sandpaper. For maximum
durability, a minimum of 3 coats are recommended.
DRY AND RECOAT
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 1 hour and can be recoated in 2 hours. Allow 24
hours before full use.
CLEAN UP
Wipe off tip before storing. Clean-up wet paint with xylene
or mineral spirits. Properly discard empty container. Do
not burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object
into the valve opening.