Technical Specifications
TECHNICAL DATA VAR-11
VARATHANE
®
SOFT TOUCH POLYURETHANE
R
Form: GDH-432
Rev.: 120617
1
.DESCRIPTION AND USES .
Varathane
®
Soft Touch Polyurethane is an acrylic polyurethane
formulated to provide a soft, smooth feel to the coating surface.
The matte finish protects against smudges and fingerprints. The
specially designed water-based formula provides excellent
scratch and stain resistance. It provides fast dry times as well as
the convenience of easy soap and water clean-up. It is ideal for
all interior wood surfaces including furniture, doors, trim, and
more. Not recommended for outdoor surfaces or floors.
.PRODUCTS .
SKU Description (Matte Finish)
262074 32 ounce Quart
262075 8 ounce Half-pint
.PRODUCT APPLICATION .
SURFACE PREPARATION
Previously Finished Surfaces – To ensure proper adhesion,
surfaces must be clean, dry, and free of wax, grease, oil, shellac,
lacquer, mildew, and polishes. Remove wax with a wax stripper,
shellac with a paint stripper, and mildew with a solution of 10%
household bleach and water. Old finishes in poor condition
should be removed. Sand using 120-220 grit sandpaper to
obtain a smooth surface. Do not use steel wool as rust may
develop after the finish has been applied. Remove all sanding
dust using a vacuum, tack cloth, or a clean, lint-free cloth.
Unfinished Surfaces – Sand using 120-220 grit sandpaper and
remove all sanding dust using a vacuum, tack cloth, or rag
dampened with mineral spirits. If a filler or putty is used, make
sure it does not contain wax allow enough time for it to dry
thoroughly.
Stained or Painted Wood – For best results, use Varathane
®
Premium Stains or Varathane
®
Premium Fast Dry Stains prior to
using Varathane
®
Soft Touch Polyurethane. Follow the stain
manufacturer’s recommendations before coating with
Polyurethane. Apply Varathane
®
Soft Touch Polyurethane
directly over thoroughly cured stain. Test a sample for product
compatibility.
..PRODUCT APPLICATION (cont.) .
SURFACE PREPARATION (cont.)
WARNING! If you scrape, sand or remove old paint, you may
release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN
SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved
respirator to control lead exposure. Clean up carefully with a
HEPA vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
APPLICATION
Stir thoroughly before and during use. Varathane Interior Matte
Polyurethane appears milky when wet but dries to a clear finish.
Do not apply in direct sunlight. Use in an area with adequate
ventilation such as an open garage. Apply only when air
(ambient) temperature is between 60-90°F (16-32°C) and
relative humidity is below 85%. Use full strength. Do not thin. To
prevent bubbles in the finish, DO NOT SHAKE and do not over-
brush, or apply with a roller.
Apply using a good quality synthetic bristle brush, foam brush, or
applicator. Apply in the direction of the wood grain in a smooth
uniform coat. Allow the finish to dry 2 hours before re-coating.
Lower temperatures and/or higher humidity may cause slower
dry times. Re-coat only when previous coats have dried clear
and feel hard. The coating should no longer feel tacky to the
touch. Apply a second coat after 2 hours. Do not apply more
than 2 coats in 24 hours. Sanding between coats is not required.
A minimum of three coats is recommended. If wood grain raises,
sand smooth before applying the final coat. Allow the finish to dry
48 hours before moderate use. Allow 7 days before subjecting
the surface to normal usage.
CLEAN-UP
Clean application tools and equipment with soap and water.