Technical Specifications
STAIN & POLY
TECHNICAL DATA
VAR-10
VARATHANE
®
ONE-STEP STAIN & POLY SPRAY
].DESCRIPTION AND USES .
Varathane
®
One-Step Stain & Poly Spray is formulated to
stain protect wood with polyurethane in one easy step.
Varathane One-Step Stain & Polyurethane contains
premium pigments which provide deep, rich color and the
high quality Varathane polyurethane, which provides a
smooth, even protective finish. It is ideal for use on all
interior projects including moldings, wood furniture, trim,
cabinets, doors, and paneling. It is NOT recommended for
floors.
.
. PRODUCT APPLICATION .
SURFACE PREPARATION
Proper surface preparation is important. All surfaces must
be clean and dry, and free of any dirt, oil, grease, wax,
polish, and any other contaminants. Remove any existing
finishes with sandpaper or stripper. Prepare bare wood for
staining by sanding in the direction of the grain. Begin with
#150 grit sandpaper and progress through #180, #220 and
#320 grits. Before using product, remove all sanding dust
and dirt with a vacuum and grease or glue with a clean rag
dampened with mineral spirits.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
PRODUCT APPLICATION (cont.)
SPRAYING CONDITIONS
Use outdoors or in a well-ventilated area such as an open
garage. Avoid spraying in very windy, dusty conditions.
Cover surrounding area to protect from spray mist.
TESTING COLOR
Be sure to test the Stain & Polyurethane to verify the
desired color. To test, apply in an inconspicuous area. For
a deeper color, additional coats may be applied.
APPLICATION
Shake can vigorously for one minute after mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Shake often during
use. Apply when temperature is between 50-90°F (10-
32°C) and humidity is below 65% to ensure proper drying.
Hold can upright 8-12" from surface and spray in a steady
back-and-forth motion, slightly overlapping each stroke.
Spray multiple thin coats until desired color is achieved.
Keep the can the same distance from the surface. Keep
the can in motion while spraying. If overspray occurs, use
a small bristle brush to remove or even out excess stain.
Surface can be recoated within 2 hours or after 48 hours.
If recoating after 48 hours, repeat the surface preparation.
A second coat can be applied after 4 hours. Lightly sand
between coats, with #320 grit sandpaper. REMOVE ALL
SANDING DUST BEFORE APPLYING ADDITIONAL
COATS.
DRY TIME
Dry and recoat times are based on 70°F and 50% relative
humidity. Allow more time at cooler temperatures. Dries to
touch in 2 hours, to handle in 4 hours, and can be re-
coated after 4 hurs.15 minutes and to handle in 1-2 hours.
CLEAN-UP
When finished spraying, clear spray valve by turning can
upside down and pushing spray button for 5 seconds.
Clean up wet stain with mineral spirits or paint thinner.
CLOGGING
If valve clogs, twist and pull off spray tip and rinse it in a
solvent such as mineral spirits. Do not stick pin or other
object into the stem.