User manual Fun-2-Go Van Raam BV Aaltenseweg 56 7051 CM Varsseveld Netherlands 06.
Contents Contents ........................................................................................................................ Contact details manufacturer......................................................................................... Conformity ..................................................................................................................... Introduction..................................................................................................................
Introduction This user manual gives important and necessary information about the use of your bicycle. We ask you to go through the manual thoroughly before using the bicycle. READ THOROUGHLY! Delivery - bicycle with possible packaging user manuals (s) possible charger (s), depending on options Intended usage The bicycle is designed for normal use on level and solid ground. The usual bicycle caution should always be taken into consideration.
Safety measures Ensure the bicycle is in good condition each time before using it. Check before each ride that the brakes are in order. Check the lights and reflectors. Regularly check whether all screw joints are tight. Regularly check whether the wheels, the handlebars and the saddle are secure. Make sure there is sufficient air in the tyres. Only use the bicycle on a solid and level surface.
Load The maximum load should not be exceeded. See information in the index of technical details on page 20. By permitted load we mean the total load, including the load in the basket. Make sure that the permitted basket weight is not exceeded. People are not to be transported in the basket! Damaged or worn out parts The replacement and repair of parts (frame, forks, illumination, brakes, drive mechanism and the handle bars) should always be performed by a dealer.
Seat position The seat position is correctly adjusted when the cyclist is sitting on the bicycle and puts a foot on the pedal in the furthest position. Adjust the seat in such a way that the leg is stretched but still relaxed. To adjust the seat: 1. Pull the handle up. 2. Move the seat to the correct position and release the handle. 2. 1. Handle bar height The height of the handle bars affects the comfort of the ride. It determines the pressure on the hands and the position of the back.
Position handle bars You can tilt the handle bars. This influences the distance from the handle bars to the upper body. Determine your own most comfortable position by using the bike. 2. To tilt the handle bars: 1. Slightly loosen the screw with an Allen key. 2. Put the handle bars in the desired position and then tighten the screw very firmly again. 1. Accessories Depending on your order, you can use the accessories as described below.
Foot support The foot support is fitted to the pedal with a balance block. Lower leg support To fit the lower leg support: 1. First fit the lower leg support to the metal plate (A). 2. The lower leg support is then fitted to the foot support. Make sure that plate (B) is under the pedal and plate (A) is between the pedal and the foot support. 3. Adjust the height of the lower leg support in such a way that it matches the lower leg of the cyclist. 4.
Speed hub co-driver The main driver can adjust the co-biking of the co-driver with the speed hub. There are three positions: 1. The pedals of the co-driver move independently of the pedals of the main driver. The pedals move free and the codriver can not cycle. 2. The pedals of the co-driver move independently from the pedals of the main driver. The co-driver can cycle also. 3. The pedals of the co-driver are moving together with the pedals of the main driver. The co-driver has to cycle also. 2.
Armrests The armrests can be switched upwards. Footrest The footrest is mounted on the adapter. 1. The adapter can be removed from the bike frame. To do this: 1. Slightly loosen the handle behind the footrest. 2. Slightly loosen the handle at the crank. 3. Slide the clamp out of the bike frame. To assemble the adapter again, follow these steps in reverse order. 2. 3. User manual Fun-2-Go 06.
Comfort seat on the bike frame. Comfort seat and children-comfort seat Depending on your order, the comfort seat is mounted on the bike frame or on the childseat adapter. To adjust the position of the seat correctly, the driver puts a foot on the pedals at the furthest position. Adjust the position in such a way that the leg is stretched but still relaxed. (children-) comfort seat on the child-seat adapter. To adjust the seat on the bike frame: 1. Pull the handle up. 2.
Position backrest comfort seat The backrest can be adjusted to the desired position. To do this: 1. Loosen the wing nut slightly. 2. Put the backrest in the desired position. 3. Tighten the wing nut again. 2. 1. Position backrest comfort seat (only seat on child-seat adapter) 2. The back rest can be adjusted to the desired position. To do this: 1. Slightly loosen the screw with an Allen key. 2. Put the backrest in the desired position and then tighten the screw again. 1.
Transporting a walker To firmly attach a walker to the back of the bike: 1. If possible, fold in the walker. 2. Loosen the star knob. 3. Pull the clamp up. 4. Place the walker with the upper bar in the bracket [A]. 5. Pull the clamp [3] down so that the upper bar is closed in. Tighten the star knob again. 4. 3. [A] 1. 2. To disassemble the rack, all screws can be loosened with an Allan key. Once they are loosened, all the pipes can be taken out of the frame. User manual Fun-2-Go 06.
Wheelchair carrier To attach the wheelchair on the back of the bike: 1. Place the wheelchair on the supports. 2. Wrap the belts around the tires and then through the buckle. Next, tighten the belts thoroughly. 1. 2. Loosen the screws with an Allen key to adjust the supports. Loosen the screws with an Allen key to remove the rack. When loosened, the rods can be pulled out of the bike frame. User manual Fun-2-Go 06.
Electric motors The tricycle can be equipped with an electric Silent motor system or Heinzmann. Silent Electric motor The Electric motor has the following Functions: - Pedal assistance while cycling On/of Button - Launch control - Backwards pedaling with assistance Stand 1, 2 or 3 Launch Con Press the on/off button to turn on the motor . After the system is turned on, the electric motor is active in level 1. Level 1 provides light support. Level 3 provides optimum support.
When you push the bicycle, turn off the motor. When the motor is not used for several days, the battery switches into the sleeping mode. This to protect the batteries. To activate it, you must connect the battery to the charger for a few seconds or cycle the bike forwards and push the on/off button to activate the system. Charging the Battery: For the best performance and to prolong the life of the battery, we recommend that you charge the battery at home at room temperature.
4 Connect the charger plug into the socket. The red light on the charger will light up. 5 Depending on the battery level, the charging time is about 4 hours. If the green light is on, the battery is charged. 6 Once the battery is charged, pull the plug from the socket first.. 4. 7 Then pull the connector from the battery. 8 Put the battery back in the holder of the cycle and close the lock. It is also possible to charge the battery while it is still in the holder.
Heinzmann Electric motor The bicycle can be supplied with an electricHeinzmann motor. There are 2 types available. Accelerator: The electric motor is operated by using the accelerator. By using the cockpit you start the motor and determine the power of the motor. This motor accelerates and drives with a speed up to 6 km/h maximum. For more speed the cyclist has to pedal as well. Pas-Vario: The electric motor is operated by the cockpit.
Charging the battery: The charging point is situated under the seat at the backside of the bicycle. To charge the battery: 1. First connect the charger plug to the charging point under the seat. 2. Put the charger plug in the wall socket. 3. Depending on the state of the battery, it needs 4 to 12 hours to charge. The battery is completely charged when the green lamp lights up. 4. As soon as the battery is charged, first take the plug from the wall socket and then disconnect the charger from the bicycle. 1.
The batteries can also be taken from the containers and charged somewhere else, indoors for instance. To do this: 1. Loosen the charge connector of the batteries from the charging point under the seat. 2. Undo the lock of the fastening device and open it. 3. Take the batteries from the containers. 4. Put the batteries down and connect the charge connector of the batteries to the connector of the charger. 5. Put the charger plug in the wall socket. The red light will light up. 6.
Before the first use Parking brake Always use the parking brake if you park the bicycle and leave it behind. Gears Standard the bicycle has 8 gears. The gears are used by turning the grip. Do not use the pedals when turning the grip. Illumination The back light works on batteries. Push the button to switch the light on and off. The light has 2 modes; steady and flashing. The front light works on the dynamo. Push the button so that the dynamo moves against the tyre.
Check before every ride: the brakes (including the parking brakes) the tyre pressure the illumination that all parts are secure Contact your dealer and do not use your bicycle if you identify any irregularities! As with all mechanical parts, the bicycle is subject to wear and tear and high loading. If a component fails, it can lead to very dangerous situations. This can lead to damage or injuries to the user of the bicycle.
Maintenance and adjustments to be done by owner Below you can find the instructions for maintenance and adjustments that you can do yourself on a regular basis, which will keep your bicycle in top condition. Cleaning The frame of the bicycle can be cleaned with a damp cloth. For areas that are dirtier you can use a mild detergent. The wheels can be cleaned with a damp brush with plastic hairs (not a wire brush!) The grips and the seats (except the upholstery) can be cleaned with mild soap and water.
The correct tension of the chains There are three chains on the bicycle. The chains should not be too tight. They should hang loose. Without effort you should be able to move the chain up and down, half a centimetre approximately. To keep the tension of the central chain correct, a special tensioning wheel is fitted by the back axis of the bicycle, as an integrated chain tensioner. To adjust the tension of the chain: 1. Slightly loosen the screw.
Repairs and maintenance to be done by dealer It is recommended that the bicycle has a yearly inspection carried out by the dealer. In the event of technical trouble or faults, the bicycle should be taken to the dealer for repairs immediately. The replacing of safety-related components (especially frame, brakes, illumination, handle bars, front fork and actuation) should be performed by the dealer.
Frame number The frame number is printed on the sticker. This sticker is located on the frame, see the image below. Example sticker: Frame number Position of sticker: on the back bridge tube User manual Fun-2-Go 06.
