Shower Door 1/4" glass (6mm) CAUTION: To reduce the risk of breakage, keep corner protectors on glass while installing. Keep corner protectors for use in case future adjustments are needed. Consult your local plumbing codes prior to installation. Recommended Clearance Heights for Installation: 58 inches (147.3 cm) MODEL: 1033458MBO6CT Recommended Width for Installation: 1033458CHO6CT 34-inch enclosure: inches (86.4 87.
Drill Bits 21/4” (3mm) dia. Screw Driver 0) Drill Level HSS Silicone Measuring Tape Soft Head Pencil Knife Sealant MASONRY DRILL) ( Safety Glasses | BIT FOR TILE ay @6mm | J Glove Carpenter's Squarer| | Masking or painter's Hack Saw tape TIE Metal File rd CAUTION: When cutting or drilling metal components or when handling glass, to reduce the risk of personal injury, protective eye wear, gloves, and closed-toe shoes are required.
CAUTION Please carefully read the following important safety information before handling or installing this shower. There is a risk of serious injury while handling this product. To minimize these risks, please note: » Always wear safety glasses and gloves while handling. + Always follow the installation instructions. + Inspect glass for damage before installation.
PART# DESCRIPTION A Bottom Anti-Water Strip Door panel B C Wall Jamb D Top Cover Cap Handle
Top Cover Cap Handle B X1° \_ Door panel Wall anchor Screw @6x38mm ST4*30 Fitting ST4*10 4 pcs 4 pcs 4 pcs 4 pcs A Additional spare parts are included.
A CAUTION: To avoid personal injury or property damage, identify components and read all instructions before installing. This Door can be installed to open from either side of your enclosure depending on noncontroversial valve location. The Glass Door should be installed on the same side as noncontroversial valve for optimal water retention. NOTE: This model is reversible for right or left-hand door installation. The left-hand door installation is shown throughout this manual.
Wall Jamb(C) Installation ~~ _ [Confirm the Wall Jamb(C) is NOTE | | plumb with a level before marking |the location of the holes for drilling. X1 Wall Jamb Fig.a NOTE Center the Wall jamb (C) on the Threshold.
Fig.a see NOTE Fig.b Lo Ll Sw Fig.c Wall Jamb(C) Installation 1.Drill the holes as Fig.a and Fig.b; 2.Apply silicone into the groove along the entire length of the Wall Jamb(C) as Fig c; 3.Attach the Wall Jamb(C) to the wall as Fig Stud is presented behind the wall: drill a pilot hole into the stud and use the ST4.0 x 30mm Pan Head Screws (bb) Stud is presented behind the wall: drill a hole and insert the Wall Anchors (aa) and use the ST4.0 x 30mm Pan Head Screws (bb).
Door panel(B) Installation AN “ The Door panel(B) Profiles can be adjusted up to 3/8” within the Wall Jamb(C) for overall width or to correct NOTE ] for out-of-plumb conditions within the model size. Screw them together after making final adjustments. elm See label.
Fasten the Door panel(B) r=" | | After final adjustments, drill &1/8” holes in the Wall Jamb (C). Drill only through the first layer of the Door panel Profile and ‘NOTE | | install the ST4.0x10mm Pan Head Screws (dd) using the Decorative Covers and Washers (cc) [Ex Adjustment 3" max "om Ca 1 L FE [ Threshold must be level 0 Include the washers when Stomacher 'an Head Screw ~~ installing the ST4.0x10mm m 1 NOTE, Pan Head Screws (dd) i | and Decorative Caps (cc) .
NOTE Handle(E) Installation Attach the Handle (E) to h the Door Panel (B) . Be sure to use all of the SN supplied rubber gaskets to “ = protect the glass.
Top Cover Cap Anti-water Strip (A) Installation Attach the Bottom Anti-water Strip (A) to Door panel (B) .
SEALING ( NOTE | | The surfaces need to be clean and free of debris before applying silicone. | A OTE) Ensure that the Shower door closes tightly and opens smoothly. \ / Apply a good quality silicone sealant along the Wall Jamb(C) A | Allow 24 hours for the silicone to cure before using the shower. | Apply Silicone Se supplied).
