SHOWER SCREEN WITH DOUBLE SLIDING DOOR INSTALLATION INSTRUCTIONS Maintenance tip: TT The following substances or articles may cause physical harm and/or damage the shower door. Do not use them for cleaning: Acid and alkaline solvents,chemicals such as hydroelectric acid,acetone thinner,solvents,cleansers, or polishers,nylon brooms or sandpaper.
PREPARATION 4. WE STRONGLY RECOMMEND THAT A LICENSED AND INSURED PROFESSIONAL CONTRACTOR TO INSTALL THIS PRODUCT INCLUDING THE ASSISTANCE OF A SECOND PERSON DURING INSTALLATION. 2. After opening all boxes and packages, read this introduction carefully. Hack that all of the needed parts are included in the package by marking all the components on the "Detailed Diagram of Shower Door Components”. Examine boxes and packages for shipping damage.
No. Description QTY No.| Description QTY 1. | Upper Guide Rail 1pc 12. Screw M4X60 6 pes 2 | wall Prof apes 13.| Roller 4 pcs 3. | Glass Door Stopper 8 pcs 14.| Allen Key PCs 4 Safety Pin 4 pcs 5. | Screw cover apes 6. | Towel Bar apes 7. | Glass Door 2 pes 8 Anti-Splash threshold 1pc 9. | Guide Block 2 pes 10.
TIPS 01: Open the packaging carefully and inspect all the necessary parts using detailed diagram and component list in your manual as a reference. Before discarding the carton, check for small hardware bags that tend to fall to the bottom of the box. If any parts are damaged or missing, please contact us for replacement. 02: Retain these installation instructions for future use if in need. 1. Measure the distance between two a finished walls. This distance is marked " as W.
2. Your Upper Guide Rail (1) and Bottom Guide Rail (8) have been precept for your Shower model opening width, eg.60" for shower width. If W-width of your wall-to-wall opening is equal to the size of your Shower model, it is unnecessary to cut the Upper Guide Rail(1) and Bottom Guide Rail(8) and you can continue to Step 3. If W-width of your wall-to-wall opening is less than the size of your Shower model, you will need to cut the Upper Guide Rail and Bottom Guide Rail. 1.
Fig 3 3. Apply some silicone onto the bottom of the Anti-splash stick it onto the shower base/threshold in front of the Glass Door.
4. Clip the Wall Profile(2) into the end of the Anti-Splash threshold(8).
OUTSIDE INSIDE Ensure the Wall Profile(2) cling to the wall at both side and vertical to the floor.Outline the drilling hole position on the Wall Profile(2). Please see Fig 5 for details a \WZc INSIDE OUTSIDE
6. Drill the holes on the wall using drill bit and apply silicone into the holes, knock in Wall Anchors (10). Please see Fig 6 for details Right side wall Left side wall a. b. Cc.
Fig 7.Apply some silicone onto the back of the Wall Profiles.
a . Screw M4X60 I i soewMaxe0 Fig 8 8.
9.Clip upper Guide Rail(1) into Wall Profile(2) Please see Fig 9 for details J I 9.1.Position Glass Door Stopper(3) in the slot of wall profile(2) and snap into place. Put on screw cover in place.
Fig 10 10. Outline the drilling position. Install ONE Guide Block(8) on the Anti-Splash threshold (8) Drill two holes on the Anti-Splash threshold(8) bit and apply silicone into the holes, insert the Wall Anchor(10). In stall ONLY ONE Guide the Anti-Splash threshold using the screwM4X30(11).
Fig 12 12.Rise the Glass Door to make rollers hang on the Top Guide rail.Slide the glass door to one side of wall and clip into the Glass Door Stopper(3).
OUTSIDE Fig 13 13. Put the rest Guide Block(9) under the glass door(7) on the shower base,outline the drilling position.And then take off the glass door and put it aside.
Fig 14 14.Drill the holes on the shower base using bit and apply silicone into the holes knock wall Anchor in.Take off the metal sheet) from the Guide Block,and lock the Guide Block baseball) using screw M4X30(11). Put the metal sheet (9B) back to the Guide Block baseball.
Fig 15 15.Hang on the glass to the top Guide Rail again and place the glass bottom side to the Guide Block(9) slowly.
17. Make sure that the Glass Door with Rollers hang on the Upper Guide Rail(1), and the glass bottom is inside the Guide adjust the screws of the rollers(13) and safety pin{4), to make sure the glass door could be sliding smoothly. Please see Fig 17 for details Fig 18 18. Apply silicone sealant on the seams between the Anti-Splash Threshold and the shower tray/threshold, and between the wall and the wall profile. See Figure 18 for details.
