CEMENT MIXER 6 CU. FT. Model 45198 OPERATING INFORMATION ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright© 2001 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
SPECIFICATIONS TABLE Weight 690 lb. Capacity 6 Cubic Feet Drum Diameter 28” Pneumatic Wheel Diameter 12” Barrel Pulley 14.5” Gas Engine HP 7.5 HP Gas Engine Pulley 3” Gas Engine Speed 3,600 RPM Drum Speeds 20 RPM (Low speed to keep cement from setting) 36 RPM (Maximum speed for heavy mixing) Towing Speed Less than 25 MPH NOT TO BE TOWED ON PUBLIC ROADS OR HIGHWAYS.
6. DRESS SAFELY. Nonskid footwear or safety shoes should be used when working with this product. Do not wear loose clothing or jewelry as they can become caught in moving parts. Wear a protective hair covering to prevent long hair from becoming caught in moving parts. 7. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS. 8. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etcetera. 9. STAY ALERT. Watch what you are doing at all times.
2. PRIOR TO USING THE CEMENT MIXER, MAKE SURE YOU READ AND COMPLETELY UNDERSTAND THIS INSTRUCTION MANUAL AND THE GAS ENGINE MANUFACTURER’S INSTRUCTION MANUAL. 3. USE COMMON SENSE WHEN HANDLING GASOLINE. Transport gasoline only in approved safety containers. Do not refuel the Gas Engine with the Engine running or while it is hot. Do not smoke when refueling the Engine. Wipe up any fuel spills on the Engine. Do not operate the Cement Mixer if there is evidence of a fuel leak.
OPERATING INSTRUCTIONS NOTE: All parts below refer to the parts listed and shown on pages 8 and 9 of this manual. 1. CAUTION: Do not attempt to move the Cement Mixer when it is full and/or in operation. 2. Place the Cement Mixer on a solid, flat, and level surface that is capable of supporting the weight of the mixer and it’s load. 3. Start the Engine (45), and allow it to reach the appropriate operating temperature as instructed in the Engine manufacturer’s operating manual. 4.
9. To discharge the cement mix, grasp the Hand Wheel (51) firmly with one hand and release the Brake Handle (60). Then, slowly turn the Hand Wheel counterclockwise to empty the Drum (4). CAUTION: To prevent accidental discharge of the cement mix, do not release the Brake Handle without holding the Hand Wheel firmly. Always make sure the Brake Handle is fully engaged after discharging the concrete mix and before refilling the Drum. (See Assy. Diagram.) 10.
MAINTENANCE AND CLEANING 1. CAUTION: Never perform any services or maintenance on the Cement Mixer while it is running. Before performing services or maintenance, turn off the engine and disconnect the spark plug wire to prevent accidental starting. 2. Before each use, inspect the general condition of the Cement Mixer. Check for loose screws, misalignment, binding of moving parts, loose or broken parts, and any other condition that may affect its safe operation.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Parts List SKU 45198 For technical questions, please call 1-800-444-3353.
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 45198 For technical questions, please call 1-800-444-3353.
