Owner's Manual
VAIL
AMP
INSTALLATION
1.
Prior
to
actual installation
of
the
VAIL
Amp,
it
is
necessary
to
run
speaker cable
to
the amplifier location.
2.
Use
the provided cut-out template
to
align and cut opening.
If
you
are
not
sure
of
potential obstruction behind the mounting
area,
start by cutting a small penciled mounting hole. Cutting a small
hole at
an
angle first will make drywall repair much easier
if
necessary.
3.
Once confirmed that there
is
no obstruction behind the mounting
area,
finish cutting the hole at a 90 degree angle.
4. Connect the speaker cables
to
the speaker
output
phoenix
connector while ensuring polarity
with
the speakers,+
to+
and -
to
- and tighten with small flat head screw driver. Then plug
to
the
back
of
the
VAIL
Amp.
5.
Connect the
CAT-5
cable and
16
AWG
power cable
to
the back
of
VAIL
Amp and feed through the wall opening
to
Wall
Plate location.
6.
Insert
VAIL
Amp into wall opening
with
micro
USB
and 3.5mm plugs
for
Echo
Dot on the
top
of
the amplifier and tighten the
two
mounting screws on the front
of
the amplifier.
Note:
Do
not overtightened mounting
screws.
This
may damage
the
amplifier, wall
surface,
or
both.
WALL PLATE INSTALLATION
1.
Choose a location for the wall plate, preferably near
an
electrical
outlet.
2.
Use
the provided cut-out template
to
align and cut opening.
If
you
are
not
sure
of
potential obstruction behind the mounting
area,
start
by cutting a small penciled mounting hole. Cutting a small hole at
an
angle first will make drywall repair much easier
if
necessary.
3.
Once confirmed that there
is
no obstruction behind the mounting
area,
finish cutting the hole at a 90 degree angle.
4.
Feed
CAT-5
cable and
16
AWG
power cable through hole and connect
to
the back
of
the
wa
11
plate.
5.
Use
provided color matched screws
to
secure wall plate
to
surface or
low voltage single gang box or bracket.
Note:
Color
matched
screws
are intended for any in-wall low-voltage
single
gang
box
or
bracket.
6.
Connect any local audio source with variable audio outputs with
an
analog
RCA
cable.
7.
Connect any powered subwoofer using a subwoofer cable.
8.
Connect provided 24v power supply
to
electri.cal outlet.
OPTIONAL
SIDE
VIEW
OF
SURFACE
First
Cut
\
.------;p~,,,.,.-"
______
,§
1
',,
45°
__/''
..__
_
__.IV
Second
Cut
~l-1
-)-
Vail
Amp
~
I
WIRE
DIAGRAM
wall
Plate
CatsCIIIII
•
---
~----
·--
r=1·=-i
.....
·-I
7
(#
AMAZON
ECHO
DOT
(GEN 2)
MOUNTING
90°
•
1.
Connect the Micro
USB
Power Plug
to
the back
of
the
Amazon
Echo
Dot.
2.
Connect the 3.5mm audio plug
to
the audio
output
on the
back
of
the Amazon
Echo
Dot.
Note:
Do
not
forcibly
pull
on
the
micro
USB
or 3.5mm
cables
as
this
will damage
the
VAIL
Amp.
3.
Turn
ON
VAIL
Amp
to
either 4-Ohm or 8-Ohm setting
depending on impedance requirements.
4.
Insert
Echo
Dot at a slight angle with connectors on
top
in
first, then gently push on the
bottom
to
fully mount
Echo
Dot.
5.
Make sure
Echo
Dot buttons
are
level
to
the wall or surface.
6.
You
may need
to
adjust the
two
VAIL
Amp mounting screws
to
ensure that the
VAIL
Amp
is
also level.
7.
Clip on the trim plate with the four clip points located on the
top, bottom, left, and right side
of
the
VAIL
Amp.
Note:
Do
not
over-press
the
clip
points.
This
may damage
the
amplifier, wall
surface,
or
both.
VAIL
Plug Power Supply
(PPS)
- When replacing in-wall volume controllers
with
the
VAIL
Amp, we recommend the
PPS
to
convert speaker cable from the
amplifier into injected power cables.
3