HDMI® over Single Coax Cable Extender Vanco Part Number: 280567 Technical Support www.vanco1.com • info@vanco1.
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters. WARNING 1. Do not expose this unit to water, moisture, or excessive humidity. 2.
FEATURES The Vanco 280567 HDMI over Single Coax Cable Extender with IR extends high definition video and audio signals and IR, at a distance of up to 100m/328ft over a single RG6 coax cable. With only one cost effective Coax cable, high definition sources with HDMI outputs can be connected to high definition displays with HDMI inputs over long distances. Deep color video, and HDCP is supported and compatible with the 280567.
SPECIFICATIONS HDCP Compliance....................................................... Yes Video Bandwidth......................................................... Single-link 225Mhz [3Gbps] Video Support............................................................ 720p/1080i/1080p @60 Audio Support............................................................ PCM (up to 7.1 ch) 48KHz Transmission Range....................................................
PANEL DESCRIPTIONS Transmitting Unit 1 3 Receiving Unit 2 4 5 6 9 7 8 10 1. HDMI: Connect the HDMI source with an HDMI cable. 2. IR TX: Connect included IR TX blaster and assign to corresponding source for source control 3. Coaxial: Connect the coaxial cable to the HDMI Receiver 4. POWER LED: This red LED illuminates when the device is connected to the power supply 5. DC IN: Plug the 5V-12V DC power supply into the unit 6. Coaxial: Connect to the HDMI Transmitter with coaxial cable 7.
CONNECT AND OPERATE BluRay® Player HDTV HDMI IR Transmitter Front Back HDMI IR Receiver Front HDMI over Coax Cable Back 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit. 2. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit. 3.
IR IR BLASTER (TX) Plug IR Blaster into IR TX port of transmitter unit (280567-TX); place blaster in front of the IR eye of the source. IR RECEIVER (RX) Plug IR Receiver into IR RX port of receiver unit (280567-RX); place receiver at or near display.
NOTICE 1. Vanco HDMI and Coax cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets. 3. The transmission length is largely affected by the type of Coax cables utilized, the type of HDMI sources, and the type of HDMI display. 4.
TROUBLE-SHOOTING 1. Best results are usually achieved when the source and display resolutions are the same. If resolutions differ, the extenders will try to adjust the signal to match the resolution of the HDTV with the lowest resolution. This will result in a picture with a lower resolution on the other HDTV sets. 2. If you do not get audio and video, access the “setup” menu on the TV to adjust the audio and video settings.
LIMITED WARRANTY With the exceptions noted in the next paragraph, Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of two years from the date of purchase. Should this product, in Vanco’s opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco.
TECHNICAL SUPPORT In case of problems, please contact Vanco Technical Support by dialing 1-800-626-6445. You can also email technical support issues to techsupport@vanco1.com. When calling, please have the Model Number, Serial Number (affixed to the bottom of the unit) and Invoice available for reference during the call. Please read this Instruction Manual prior to calling or installing this unit, since it will familiarize you with the capabilities of this product and its proper installation.
Vanco® International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.
