Installation Guide

ManualsBrandsVan Mark ManualsKitchen48 in. Aluminum Custom Gutter Hood Former

      

Price $10.00 US

Trim-A-Gutter

™

Model TAG50

Shown with Metal Master

20 Brake and

UniStand

™

USA2 Tool Support (each sold separately)

Gutter Hood Tools & Accessories

New Construction and Retrot

Now includes 5"& 6" inch gutter installations

Save This Guide

For Reference!

Table of Contents

Tool Setup, Bending Brakes.............................2

Tool Setup, Metal Master

20...........................3

Tool Setup, With Unilegs

™

................................4

Forming Gutter-Hood

........................................4

Existing Gutter Installation

................................4

Forming End-Caps, Miters, & Valleys

...............5

Template

...........................................................6

New Gutter Installation

.....................................6

Example Proles/Uses

......................................7

Care & Maintenance

.........................................7

Parts List..........................................................8

Patent No’s 7,500,375, 7,707,781

Other US and Foreign Patents Pending

Trim-A-Gutter

™

Model TAG50

Shown with UniLegs

™

UNL1 (sold separately)

Van Mark Web

Summary of content (8 pages)

PAGE 1
Gutter Hood Tools & Accessories New Construction and Retrofit Now includes 5"& 6" inch gutter installations Trim-A-Gutter™ Model TAG50 Shown with Metal Master® 20 Brake and UniStand™ USA2 Tool Support (each sold separately) Save This Guide For Reference! Table of Contents Trim-A-Gutter™ Model TAG50 Shown with UniLegs™ UNL1 (sold separately) Tool Setup, Bending Brakes.............................2 Tool Setup, Metal Master® 20...........................3 Tool Setup, With Unilegs™.......................
PAGE 2
-2 Tool Setup-Brakes �� Long Fast Pin 2 ea. Short Fast Pin 4 ea. �� Hex Head Small 10 ea. Hex Hd Long 4 ea. �� (L) Knob 6 ea. Washer 8 ea. Locknut 4 ea. Spacer 2 ea. �� UniMount™ Assembly U se this diagram as a reference for parts/hardware called out in these next 2 pages, though each part may only be called out once in each step.
PAGE 3
- Tool Setup-Brakes (cont.) 2” 1 1/ Track 4 Place rail L alongside right bracket K with 5/16” hole to front of brake. Slide hex head portion of screw D down track and extend through 2nd hole from end of bracket K as shown (see center arrow). Start knob F onto threads and leave loose for now. Repeat this procedure with remaining rail L and left bracket J. 5 Align front hole in rail L with front hole in bracket K. Insert Fast Pin A through front hole in rail, then through bracket.
PAGE 4
-4 Tool Setup on UniLegs™ UNL1 Extended Bracket Side View Leg Flare Rail Assembly Detail G Lay out rails L as shown with screw tracks facing up. Insert the hex head portion of screw D into each track (see Detail G). With bracket K facing downward, align holes (indicated by arrows), with hex head threads and lower into place. Tighten bracket snugly against rails with locknuts H. 1 Detail H 2 From opposite end of rails, again insert the hex head portion of screw D into each track.
PAGE 5
- Existing 5 & 6 inch Gutter Installation The following instructions are to be used as a guideline on getting up and running with Trim-A-Gutter™ Tools and Hardware. Before getting started, it is recommended that you check the entire gutter system for problems, such as clogged downspouts, leaks or rotted wood, before installing gutter-hood. Use these guidelines for installing new 6" brackets as well. Check end caps, outlets and seams for water-tightness.
PAGE 6
-6- End Cap Template *To download a splash or end-cap template, go to www.van-mark.com and navigate to the Trim-A-Gutter™ Installation page. Scroll down and click either the splash or end-cap image.
PAGE 7
- New Gutter Installation-Roof Mount Detail Bend Line L D ow Profile. Install gutters using brackets & anchor screws. Create a template based on this profile remembering to keep a downward pitch from the bend line to the nose. Install drip edge and underlayment, then sections of gutter-hood based on your template. Install shingles even with bend line.
PAGE 8
Trim-A-Gu�er™ Parts List Effective 11-15-11 For Quick “Same Day Shipment” Order Early Order Toll-Free 24 Hrs Call Free 1-800 Van Mark Fax Free 1-888 Van Mark Ref Qty Part No Ref Qty Part No Ref 1 End Block Screw Description 8 2067 21 Roller Handle Description 1 4053 40 UniMount™ Assembly Description Qty Part No 1 2 Anvil Lock Screw 4 2014 22 Roller Handle Grip 1 4625 41 1/4-20x5/8 Hex Hd 3097 13 3 Anvil Bracket Screw 1 2010 23 Bending Leaf 1 4620 42 1/4-20x1 1/