AIR-POWERED FINISH NAILER MODEL T64C INSTRUCTION MANUAL IMPORTANT: Read all safety rules and operating Instructions carefully before starting the product. Keep this Manual for future reference. Residual Risks Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors.
TABLE OF CONTENTS: TECHNICAL SPECIFIACTIONS SAFETY GUIDELINES UNPACKING KEY PARTS DIAGRAM IMPORTANT INFORMATION TYPES OF FASTENERS OPERATING INSTRUCTIONS MAINTENANCE TROUBLESHOOTING EXPLODED VIEW PARTS LIST TECHNICAL SPECIFIACTIONS: Magazine capacity(QTY.) 100pcs Nailer Drives Operating pressure: 70 to110 PSI(4.8 to 7.5 bar) Maximum pressure: 120PSI (8.3bar) Air inlet: 1/4”(6.35mm) Dimensions: 80x280x303mm Weight: 2.3kgs(5.
This manual contains information that relates to protecting personal safety and preventing equipment problems.it is very important to read this manual carefully and understand it thoroughly before using the product.the symbols listed below are used to indicate this information. DANGER! Potential hazard that will result in serious injury or loss of life. WARRNING! Potential hazard that could result in serious injury or loss of life.
-Protect the air hose and the power cord from damage and puncture. Inspect them for weak or worn spots every week, and replace them if necessary . -Always wear hearing protection when using the air compressor. Failure to do so may result in hearing loss. -Do not carry the compressor while it is running. -Do not operate the compressor if it is not in a stable position. -Do not operate the compressor on a rooftop or in an elevated position that could allow the unit to fall or be tipped over.
UNPACKING -If you discover the nailer is damaged after you have signed for delivery, please immediately where you buy for advice. -Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condition of the shipment, you should inventory the equipment. -After you open the nailer box, you should find the following. Model T64C Inventory (Figure 1) A. T64C Finish Nailer….....
WARNING! Potential hazard that could result in serious injury or loss of life. Keep hands and other parts of the body away from the tools discharge and working areas when connecting the air supply. Failure to comply could lead to serious injury or loss of life. It is recommended that a filter-regulator-lubricator is used and located as close to the tool as possible. If a filter-regulator-lubricator in not installed, place up to 6 drops of compressor oil into the inlet plug before each use.
OPERATING INSTRUCTIONS To load your nailer: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Pull pusher (B) back to magazine rail until it locked into Pusher hook(B-1). Figure 3. Catch lever engaged and magazine pusher retracted. 3. Insert a strip of Finish nailer, pointed-end down, into the magazine as shown in Figure 4. Be sure the fasteners are pointed DOWNWARD.Only those fasteners specified under TECHNICAL DATA may be used Figure 4. Loading nails into magazine. 4.
Operating If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place two to three drops of the included oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer: 1. Connect the air supply to the quick connect fitting. 2. To test for proper nail penetration, hold the nailer perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of nails you have loaded.
Single Fire Operation SINGLE SEQUENTIAL MODE The tool is specially designed for single sequential mode. This mode requires the trigger to be pulled each time a fastener is driven. The tool can be actuated by depressing the work contact element against the work surface followed by pulling the trigger The trigger must be released to reset the tool before another fastener can be driven. Clearing Jammed Nails A jammed nail must be cleared before using the nailer again.
To replace a piston and O-ring: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Remove all nails from the magazine. 3. Remove the four cap screws on the head of the nailer, near the exhaust port. 4. Remove the cap. 5. The top of the piston should now be visible inside the cylinder, which is housed in the head of the nailer. 6. O pen the nose cover as if to clear a jammed nail. 7. Watch the discharge area and push the top of the piston with your finger.
TROUBLESHOOTING (See Table 1) The following chart lists common operating system issues and solutions.please read it carefully and follow all instructions closely. DANGER! Potential hazard that could result in serious injury or loss of life. If any of the following symptoms appear while the tool is in use,turn it off and disconnect it from the air supply immediately. Failure to comply will lead to serious injury or loss of life. Disconnect the tool from the air supply before making any adjustments.
Explosive View and Parts list Issue date: Version no.: No. Figure number Description Qty.No. Figure number Description Qty. No. Figure number Description Qty.No. Figure number Description Qty. Bolt Cylinder Cover Washer Adjust nut Magazine pin Air Deflector O-ring 10*1.8 Gun Body Thrust spring O-ring 11.7*2.4 Rivet 3*7 Locating seat Bolt M5×25 O-ring 13*1.
