EFFUSION Easy Install Shower Panel Installation and User Guide Version No.: V1.
DIMENSIONS 1 5 " 2 18 1 " 8 3 4" 1 38 2 " 1 58 " 1 10 4 " 1 58 " 23 " 4 1 2 " 2 DIMENSIONS BEFORE USAGE • (H) 38.46" x (W) 5.5" x (D) 2.56" • Hand shower hose: 59.05" • Weight: Net: 10 lbs /Gross: 15 lbs • Read this Installation and User Guide before installing and operating. • Always take extra care when installing to prevent injury. Wear appropriate safety equipment. • Do not allow children unsupervised use of the shower panel.
BEFORE INSTALLATION • Before and during installation, read and familiarize yourself with all installation instructions for this product. • Keep all components, parts and accessories of this product away from small children and minors. During installation, all screws,tools and small parts should be supervised so that they do not fall into the hands of children. • Use caution at all times when installing this product.
17 11 5 4 3 2 7 8 21 15 13 1 14 6 9 18 10 20 19 16 11 6 15 13 12 11 6 -4- 14
ASSEMBLY a ASSEMBLY 9 6 7 10 11 12 1 9 b 9 c d 9 9 9 6 -5-
INSTALLATION INSTRUCTIONS • Before Installation, ensure there is sufficient clearance to accommodate the shower panel. A minimum of 19.5” is required between the shower outlet and top of your existing valve. Maximum clearance required 42”. 1 Min 19.5 Inch Ensure that the water line to the overhead shower pipe is completely shut off prior to performing any work. • Remove your existing shower head.
INSTALLATION INSTRUCTIONS 5 4 Attention: B PVC cover is not required if the water outlet is below 33.38" Recommended 10" A MIN ½ Inch Installation position will vary depending on users height. Depending on users height, it is recommended to have 10” of clearance above your head. Valve goes below this C template. Bottom of panel. • An installation template guide is included with your shower panel as a convenient method of determining the correct position of the shower panel.
INSTALLATION INSTRUCTIONS This section will guide you on measuring the required length of the Main PVC Supply Line (Part #8) relative to the final position of the Template Guide Draw a level horizontal line based on the lower-edge of the selected hole 6 8 • Measure the distance between the bottom of the template to the closest approximate hole position on the top of the template which corresponds to where the shower outlet pipe is. Refer to this distance as "d1".
INSTALLATION INSTRUCTIONS 8 • To ensure the template (and your shower panel) will be in a completely straight and level position, use a level tool against the side of the template guide to make fine adjustments to the template guide's position until fully level. • Once fully level, this will be the final position of the template guide. • Take a pencil/marker and mark the positions of the anchor screws (Part #15) for which 4 holes will need to be drilled.
INSTALLATION INSTRUCTIONS 11 • After anchors has been secured, align the mounting brackets (Part #14) using the supplied screws (Part #13). 14 x2PCS PH + 13 x4PCS For the Positioning & Mounting Brackets (Part #14), make sure that they are installed with protruding portion facing upward as shown in the drawing.
INSTALLATION INSTRUCTIONS NOTE: If the water outlet is below 33.38” on the template, the PVC cover is not required. 13 1. Peel off the paper backing to the adhesive ring for the Base Plate cover (Part #5). 2. Place the adhesive side to the wall and apply pressure to secure the Base Plate Cover (Part #5). (Note: Remove all residues to ensure the cover will bond properly) 3. Add a Filter Gasket (Part #11) into Elbow Joint (Part #3) first.
Technical Data Maximum operating pressure: 125psi Recommended pressure: 20~80psi Test pressure: 45psi ,125psi Flow rate @ 80 psi: <2.0gpm * For Safety, it is highly recommended that you familiarize yourself with all applicable local plumbing codes before installing this product. How to use Diverter NOTE: Use your exising shower valve to operate temperature and water flow to shower panel. • Shower Head Position • Hand Shower Position When the selector knob is placed in ”a” .
Diverter Valve Structure 5 Diverter valve 4 3 1 2 How to Remove the Diverter Valve 1 2 3 (2.5 mm) 1 3 1 2 • Remove the cover(#3) to open the set screw access hole. • Loosen the set screw (#1) from the valve stem and pull the knob (#2) straight out. 3 4 4 4 5 Diverter valve • Loosen and remove the gland nut (#4). • Remove the Diverter valve (#5) by pulling it straight out.
How to Install the Diverter Valve 22 1 4 5 4 Diverter valve • Tighten the gland nut (#4). Take precaution to avoid scratching the trim plate. Do not force the nut too tightly. • Place the Diverter valve (#5) into the valve body. Note the one pillar on the bottom of the Diverter valve (#5) must be aligned with the hole in the rear of the body. Adjust the knob with right position 3 • Place the knob (#2) on the valve stem.
Cleaning Recommendations Modern faucets and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the warranty. Cleaning Materials for Faucets and Showers • To remove lime scale, use only products made specifically for that purpose. Always follow the manufacturer’s instructions when using.
LIMITED WARRANTY Valore (“Seller”) and the person or entity that acquires these goods from Seller (“Purchaser”) hereby fully agrees to the following terms and conditions of the sale: Shipping fees are the responsibility of the Purchaser whether freight prepaid or freight collect.
