Operating instructions

ManualsBrandsValor ManualsLawn and Garden650IRP

Speciﬁ cations

Approvals & codes

These appliances are certiﬁ ed by ANSI Z21.88-2009/CSA

2.33-2009 American National Standard / CSA Standard

for Vented Gas Fireplace Heaters for use in Canada and

USA. These appliances are for installation directly venting

through an outside wall or through the roof.

Model 650IRN is for use with natural gas.

Model 650IRP is for use with propane gas.

Conversion between fuels may only be done using the

approved conversion kits listed in the section Options.

These appliances comply with CSA P4.1-09 Testing

method for measuring annual ﬁ replace efﬁ ciencies.

The installation must conform with local codes or, in

the absence of local codes with the National Fuel Gas

Code, ANSI Z223.1 or the Natural Gas and Propane

Installation Code CAN/CGA-B149. Only qualiﬁ ed

licensed or trained personnel should install these

appliances.

These appliances, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical

Code, ANSI/NFPA 70 or the Canadian Electrical Code,

CSA C22.1.

Ratings

*Tested to CGA - 2.17-91 High Altitude Standard in

Canada. In the USA, installations may require deration

over 2,000 feet—check local codes.

*High Altitude Installations

Input ratings are shown in BTU per hour and are

certiﬁ ed without deration for elevations up to 4,500 feet

(1,370 m) above sea level.

For elevations above 4,500 feet (1,370 m) in USA,

installations must be in accordance with the current

ANSI Z223.1 and/or local codes having jurisdiction.

Heating value of gas in some areas is reduced to

compensate for elevation—consult your local gas utility

to conﬁ rm.

For installations at elevations above 4,500 feet

(1,370 m) in Canada, please consult provincial and/or

local authorities having jurisdiction.

Model 650IRN 650IRP

Gas Natural Propane

Altitude (Ft.) 0-4,500 *

Input Max. (Btu/h) 24,000 24,000

Input Min. (Btu/h) 6,500 13,000

Manifold pressure (in w.c..) 3.95 10.5

Min. Supply pressure (in. w.c.) 5.0 11.0

Max. Supply pressure (in. w.c.) 11.0 14.0

Supply Gas

Heater engine unit 650IRN is used with natural gas

installations.

Heater engine unit 650IRP is used with propane gas

installations.

The supply pressure must be between the limits shown

in the table above.

The supply connection is

⅜ inch NPT.

The opening for the gas

supply line is at the left

side of the appliance.

Wall Thickness

The vent system (when horizontally terminated)

is approved to pass through combustible wall

construction of up to 14 inches (36 cm) thick.

A non-combustible wall can be any thickness up to the

maximum horizontal run of vent pipe allowed for the

particular installation—see Venting section.

Venting options

Direct vent installations (solid piping)

A list of all approved venting accessories is shown on

pages 38–39 of this manual.

NOTE: An 817VAK Vent Adapter is required in all

cases when using vent components other than Valor’s

551DVK Standard Vent Terminal.

Direct Vent Co-Linear Installations (ﬂ exible piping)

Converts the appliance outlet collars to accept two

3-inch diameter ﬂ ex liners for installation into existing

solid-fuel burning ﬁ replaces and chimneys. Requires a

co-linear adapter at the appliance and either a co-linear

terminal or co-linear-to-co-axial adapter and terminal

at the top of the chimney. A list of approved venting

accessories is shown on pages 38–39 of this manual.

Floor/Hearth

This appliance is approved for installation directly on

combustible material such as plywood and so on. Vinyl,

carpet, and soft ﬂ ooring require sheet metal extending

the whole width and depth under the appliance.

This appliance does not require a hearth. Combustible

ﬂ ooring may extend up to the front of the unit.