Owner`s manual

4 of 48
2.0 OPTIONS
Heater engine unit # 530 X is available in either natural
gas or LPG and comes equipped with either a simulated
log or coal fuel bed in either fuel. The 530X engine unit
is supplied standard with a rear vent D.V outlet and may
be converted to a top outlet D.V with no extra parts
required. The engine is not supplied suitable for zero
clearance, the parts required to make the engine zero
clearance are supplied with the various front trims
(except 549 front)
2.1 Appliance styles
President FS 531 Free standing cast iron stove.
(See figure 1).
President 536 For recessed application, either zero
clearance or insert . (See figure 2)
Windsor Arch 539/549 Arched Cast Iron Front for
recessed application, either zero
clearance(see fig 3) or insert (see fig
4). (549 version is insert only )
Bolero 541 Contemporary cast iron front for
recessed application, either zero
clearance or insert (see fig 5).
One of the above kits must be used with each installation.
2.2 Additional optional features
Circulating Fan Kit #555CFK Having variable speed
and temperature control, it is
designed to boost the natural
convection process through
the appliance. It may be fitted
before the fireplace is installed
or retrofitted at a later date.
Closure Plate #3336 CP 33” high x 36” wide black
closure plate with black aluminum extrusion edge. To
cover openings for insert applications.
2.3 LP Gas
LPG Conversion kit Burner & injector kit for
conversion from natural gas to
propane – Kit #554LPK.
2.4 Venting options
2.4.1 Direct vent installations (solid
piping)
One or more of the accessories listed below must be
used for each installation. See the “Location” section of
this manual.
Kit#
551DVK Valor Horizontal terminal kit with pipe
section. Maximum useable length 26”.
(66cm) (Maximum 14” thru combustible
wall section (36cm)
556 CLA Co-Linear appliance Adapter
558FLK Through the wall Dura-vent pipe
insulation kit
817VAK Adapter for Dura-vent pipes
984 Dura-vent DV GS horizontal square
terminal cap
942 Dura-vent DV GS wall thimble kit
945B 45° Dura-vent DV GS elbow
990B 90° Dura-vent DV GS elbow
908B 6” Dura-vent DV GS pipe length
907B 9” Dura-vent DV GS pipe length
906B 12” Dura-vent DV GS pipe length
904B 24” Dura-vent DV GS pipe length
903B 36” Dura-vent DV GS pipe length
902B 48” Dura-vent DV GS pipe length
911B Adjustable 11”-14
5
/
8
” Dura-vent DV GS
pipe length
981 Dura-vent DV GS snorkel termination
unit – 36” rise
982 Dura-vent DV GS snorkel termination
unit – 14” rise
980 Dura-vent DV GS Low Profile vertical
termination cap
991 Dura-vent DV GS high wind vertical
termination cap
940 Dura-vent DV GS round ceiling support
941 Dura-vent DV GS cathedral ceiling
support box
963 Dura-vent DV GS ceiling firestop
943 Dura-vent DV GS adjustable roof
flashing. Roof pitch 0/12 – 6/12
943S Dura-vent DV GS steep roof flashing.
Roof pitch 7/12 – 12/12
953 Dura-vent DV GS storm collar
988 Dura-vent DV GS wall strap
923GCL Dura-vent DV GS co-axial to co-linear
appliance connector
923GK Dura-vent DV GS co-linear termination
kit
984 Dura-vent DV GS square terminal cap
2280 Dura-vent DV GS co-linear flex
chimney liner 35ft. length.
835TG Terminal Guard
2.4.2 Direct Vent Co-Linear Installations –
for Free Standing or Recessed
Installations (flexible piping)
Converts the appliance outlet collars to accept
two 3” dia. Flex liners for installation into
existing solid fuel burning fireplaces and
chimneys. Requires 556 CLA adapter and 923
GK termination kit along with either a 980 or
991 termination cap.( 923GCL may be used in
lieu of 556 CLA adapter)
2.4.3 B-vent installations – For President
Free Standing only
Kit #552BVX converts this appliance from a
direct vent fireplace heater to a gravity vent
fireplace heater for use with a 4” “B” type vent.
A full installation and operating manual is
supplied with the kit.