Installation Manual V1.05 V-DW2425A / V-DW2440 and V-DW11025A / V-DW11040A The Sapling Company, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 215.322.6063 P. 215.322.8498 F. www.sapling-inc.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Metal Surface (Wall) Mount Installation 1. 2. 3. 4. 5. 6. Mount the wall mount box into the double gang box using four machine screws (#6-32) including in the kit. Connect the ground wire into the flush mount box using tooth lockwasher and the machine screw nut (included in the kit). Disconnect the red filter from the display panel. Connect the wiring as shown on the wiring diagram.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Connecting the Clocks to the Metal Double Mount Housing 1. Connect CON 1 to P5 on Clock 1. Make sure the polarity is followed as shown in the diagram. 2. Connect CON2 to P2 on Clock 1. 3. Connect CON 3 to P2 on Clock 2. If you have any questions, please contact Sapling Technical Support at (888) 809-6063.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Metal Double Mount Installation 1. 2. 3. 4. Screw hanger/mounting rod (included in the kit) into the crossbar (also included in the kit). Insert wires through hanger/mounting rod. Install crossbar using two (2) #6-32 screws into double gang box. Mount the double mount box into the clock base using two (2) #6 nuts and Tooth Lockwasher #6. (The double mount can be mounted either on the wall or on the ceiling).
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Plastic Surface (Wall) Mount Installation q Mount Housing to Wall and/or Gang Box - To mount the housing to the wall, drive two (2) plastic anchors into the wall (not supplied in kit) and take two pan head screws (also not supplied in kit) and drive them into the plastic inserts leaving an 1/8th inch gap between the head of the screw and the wall.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Plastic Double Mount Installation *For metal mounting bracket: Use a wall anchor that can support 50 lbs or more with a maximum screw size of 10/1.5” q Install metal mounting bracket - First, remove the metal mounting bracket from the inside of the double mount base by unscrewing the two (2) 6-32 x 1/2” screws located on the underside of the base (save these screws for step #5).
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Plastic Double Mount Installation t Snap and screw base to metal mounting bracket - Snap the base to the metal mounting bracket by first making contact with the lip in the upper side of the base and the metal mounting bracket.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Wiring Information and Jumper Settings Gray Jumper Number JP1 - 12/24 Hour Mode On 12 Hour Mode Off 24 Hour Mode JP2 - Brightness Brightest Bright JP3 - Loss of Communication Alert 5 Minutes 1 Hour Note: When using the Valcom Wireless Digital Clock in a metal double mount housing, only one clock gets connected to the wireless transceiver through the P5 connector shown above.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Frequently Asked Questions Will the clock cause interference with any of my other wireless devices? No, the Valcom Wireless Digital Clock works on 915 - 928 MHz frequency-hopping technology. The clock switches frequencies automatically when the receiver and transmitter are open, thus interference is avoided..
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Troubleshooting What happens if the clock doesn’t power up? Make sure the wiring is correct. If the clock is 24 volt, the power should be on the orange and yellow wires of the harness. If the clock is 110 volt, the power should be on the black and white wires. The middle (green) wire is ground. If the wiring is correct, take a volt meter and measure the voltage.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com FCC Wants You to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
