Installation manual

ManualsBrandsValcom ManualsHome DecorV-WMCA

Page 1

Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02)

Valcom 5614 Hollins Road Roanoke, VA 24019 Phone: (540) 563-2000 Fax: (540) 362-9800 www.valcom.com

Table of Contents

MOUNTING

Wall Mount Installation………………………………………………………………… Page 2

Double Mount Installation……………………………………………………………… Page 3

WIRING INFORMATION

Wiring Information……………………………………………………………………... Page 4

OPERATION

Operational Instructions………………………………………………………………… Pages 5 - 6

FREQUENTLY ASKED QUESTIONS

Frequently Asked Questions…………………………………………………………… Page 7

TROUBLESHOOTING

Troubleshooting……………………….……………………………………………… Page 8

DIAGNOSTIC TESTING

Diagnostic Tests Procedures…………………………………………………………… Pages 9 - 11

FCC INFORMATION

FCC Information……………………………………………………………………….. Page 12

For clocks with date codes beginning December 2009

This product is UL and cUL listed

Summary of content (12 pages)

PAGE 1
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Table of Contents MOUNTING Wall Mount Installation………………………………………………………………… Page 2 Double Mount Installation……………………………………………………………… Page 3 WIRING INFORMATION Wiring Information……………………………………………………………………... Page 4 OPERATION Operational Instructions………………………………………………………………… Pages 5 - 6 FREQUENTLY ASKED QUESTIONS Frequently Asked Questions…………………………………………………………… Page 7 TROUBLESHOOTING Troubleshooting……………………….
PAGE 2
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Wall Mount Installation 24 Volt/110 volt options shown in diagram 12” CLOCK INSTRUCTIONS 1. Connect the wiring as shown on the wiring diagram (110V or 24V ONLY). 2. Mount both plastic anchors in the wall. 3. Insert the sheet metal screws (#10) through the mounting bracket into the plastic anchors. 4. Plug the connector into the movement (110V or 24V ONLY). 5. Hang the clock on the mounting bracket. 6.
PAGE 3
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Double Mount Installation INSTRUCTIONS 1. Screw the mounting bracket to the double gang box using four (4) inner holes on mounting bracket, or mount the mounting bracket directly to the wall or ceiling using the four (4) outer holes. 2. Insert the wires through the mounting bracket (110V or 24V ONLY). 3. Route the wires through the clock hanging rod. 4.
PAGE 4
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Wiring Information ————————————— ————————————— ————————————— Sapling WIRELESS “WHERE TIMING AND TECHNOLOGY MEET” FCC ID R73AMR001 Diagnostic Switch Diagnostic LED Transmit/Receive Dependent upon model number, Valcom wireless analog clocks are powered by 2 “D” cell batteries, 24 vac or 110 vac. Page 4 Valcom 5614 Hollins Road Roanoke, VA 24019 Phone: (540) 563-2000 Fax: (540) 362-9800 www.valcom.
PAGE 5
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Operational Instructions IMPORTANT: We highly recommend installing the main transceiver (V-WMCA) before the installation of the Valcom Wireless analog clocks. In order to install the clock, simply remove the battery cover, and install two (2) D cell batteries (recommended battery type: Duracell® PROCELL®). After installation of the batteries, replace the battery cover and the clock should start correcting within five (5) minutes.
PAGE 6
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Operational Instructions Initial Setup 1. All wireless clock systems require at least one master transmitter. This may be a V-WMCA Wireless Master Clock, a V-GPS-TX Wireless Master Clock with GPS or a V-WMCRA Wireless Repeater (configured as a transmitter) that is connected to an appropriate Valcom system. 2. The master transmitter should be installed and operational prior to the installation of any wireless clocks.
PAGE 7
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Frequently Asked Questions What battery size do I use for the wireless clock? The batteries required are two (2) “D” cell batteries. The recommended battery type is “Duracell®: Procell® [D] size”. Will the clock cause interference with any of my other wireless devices? No, the Valcom analog wireless clock works on 915 - 928 MHz frequency-hopping technology.
PAGE 8
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Troubleshooting What happens if I power up the clock and the clock is not moving? The clock should move at normal speed upon power up. If it does not move at normal speed, check the battery and make sure the clock receives power. Also, be sure to remove the pin prior to starting up the clock. What happens if the clock does not receive the signal? Take the clock within close proximity to the transceiver and power up the clock.
PAGE 9
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Diagnostic Testing Overview The number of times that the switch is pressed will determine the diagnostic mode. After determining the diagnostic mode, the LED between the two (2) switches will start flashing a green light. The number of flashes will display the diagnostic number. DIAGNOSTIC #1 This diagnostic will determine how long (# of hours) since the clock last received the communication signal.
PAGE 10
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Diagnostic Testing DIAGNOSTIC #2 This diagnostic will determine the quality of the time signal. In order to enter Diagnostic #2 mode, push the Diagnostic Switch twice which is indicated by the green LED flashing twice with a one (1) second break. A. While in diagnostic modes, hour and minute hands continue to run normally. B. The second hand will display the quality of the time signal.
PAGE 11
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) Diagnostic Testing DIAGNOSTIC #4 This diagnostic will test the battery level of the clock. In order to enter Diagnostic #4 mode, push the Diagnostic Switch four (4) times which is indicated by the LED flashing four times with a one (1) second break. The second hand will display the battery level by stopping one of the numbers on the clock’s face. For example:      If the second hand lands on 2, the battery level 2.2V.
PAGE 12
Valcom 12” & 16” Wireless Clock Installation Manual (Rev 1.02) FCC Wants You to Know This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.