Installation Manual V4.3 V-WMCA Master Clock V-GPSA V-GPS-TX Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Wall Mount Installation Fig 1 1. Place the supplied template on the wall where the master clock is being mounted. 2. Mark the center point of the top right hole. Drill the hole and install the supplied anchor from the mounting kit. 3. Install the screw into the anchor and hang the template from the top right hole. 4.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Before You Get Started Installing the Master Clock with the Line Cord Receptacle Remainder of cord not shown Caution! Do not plug in the power cord until the following steps are completed. *220-240 VAC Disconnect 1. The square knockout on the wiring chassis must be removed. 2. The Heyco Bushing must be attached to the power cord as shown.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Rear View of Unit | | q | | w | | e | | r | | t q Clock 1 & 2 Sync-Wire Outputs communication relay outputs. w RS485 Input/Output systems. e Inputs This terminal block is where connections would be landed to use the master clock as a slave clock when being controlled by another system.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Remote Antenna Mounting Instructions 1. 2. 3. 4. 5. 6. 7. 8. Remove the cover of the wiring panel. Mark the four drilling points on the wall based on the drawing above. Drill the holes for the anchors supplied in the mounting kit at the designated markings from step 1. Install the four anchors in the holes that were just drilled.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Inputs – Sync-Wire Inputs Installation 59 Minute Correction 12 N.O. 15 17 24VAC Hot 8 24VAC Interface 24VAC Neutral 17 110VAC Neutral 7 110VAC Interface (EU 240VAC) 16 17 110VAC Hot Dry Contact Closure COM 58 Minute Corrections 1–4 N.O.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Fire Alarm Interface Installation / Patch Cable Installation Fire Alarm Interface Installation The Fire Alarm Interface allows a relay closure to be connected to the master clock that allows the user to interface the existing fire alarm with the Valcom digital clocks. 7 10 8 9 N.O.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Inputs – GPS Installation GPS Antenna Installation Supplied by Valcom: GPS Dome, 75’ length of RG58 cabling (optional 150’ length of RG59 cabling upon request) (refer to Figure 1.1) Not supplied by Valcom: Steel or PVC piping with 1”-14” thread or 3/4” pipe thread, teflon tape, mounting plate and hardware for piping (refer to Figure 1.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com User Level Programming Setting the Time from the LED Display To set the time, press the top button to change the hour and/or the bottom button the set the minute. See Fig 2.1. Fig 2.1 Programming the Master Clock To enter programming mode, press both the top and bottom button together simultaneously. The top button advances through the options while the bottom button changes the option.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Option 3 - Set Day: Use the bottom button to scroll between “01-31”. Option 10 - Technical Mode: If technical mode is desired, press the bottom button until “08” is reached. Setting option 10 to “08” will allow the user access to options 11-13 when the top button is pressed. Any other value will go directly to option “20” when the top button is pressed.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Option 20 - Programming the Clock #1 Circuit: Press the bottom button to scroll through “1”, “2”, “3”, “4”, “5”, “6”, “7”, “8” & “9”. Please refer to relay selection mode on page 21. Option 21 - Once a Day Pulse - Set Hour: This option is only available if “8” is selected in option 20 for once a day pulse. Press the bottom button to scroll through “00-23”.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Option 25 - Programming the Clock #2 Circuit: Press the bottom button to scroll through “1”, “2”, “3”, “4”, “5”, “6”, “7”, “8” & “9”. Please refer to relay selection mode on page 21. Option 26 - Once a Day Pulse - Set Hour: This option is only available if “8” is selected in option 25 for once a day pulse. Press the bottom button to scroll through “00-23”.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Option 30 - Set the Primary Input: Press the bottom button to scroll between “1-13” to select the input.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Option 35 - Once a Day Pulse Input - Set Minutes This option is only available when option 30 or 31 is set to 11. Press the bottom button to scroll through “00-59”. Option 36 - Once a Day Pulse - Set Seconds This option is only avaiable when option 30 or 31 is set to 11. Press the bottom button to scroll through “00-59”.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Option 50 - Entering Diagnostic Mode Press the bottom button to scroll between “E - d”. Setting the option to “E” will enable the option and will enter diagnostic mode. Setting the option to “d” will disable the option and upon depressing the top button, the clock will return to the time. Option 51 - Sends Diagnostic to Slave Clock Pressing the bottom button will scroll from “1-5 and 9”.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Error Codes Error Codes on LED Display When one of the following errors occurs, one of the LED lights located above one of the six characters on the LED display will being to flash. See figure below indicating the error each flashing light is associated with.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming *The web interface is an optional feature and is not available on all units. *Please make sure that ports 123 and 80 in both directions are open on the firewall. Accessing the Web Interface (when connected via DHCP) 1) Plug in a patch cable to the unit, and then into a switch on your network.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming Log In q w e q Password There are two levels of passwords that will enable the user to access features. The first level is the user level programming that includes features like setting the time, date, adding and editing events and schedule changes. The default password for the user level is 1111. It can be changed in the technician level.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming Date/Time q w e q Time This field is where the current time is displayed. The time can be edited by clicking within the field, and typing in the desired time. The time must be entered in 24 hour format (HH:MM:SS). After typing in the desired time, click the Submit button to set the time on the unit (if there is no input connected).
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming System Settings w q e r t y q User Password This field allows the user to enter a new password for the user level programming. The password must be entered twice before being changed. The default is 1111. w e RS485 Data Rate r GMT Offset This field sets the positive or negative offset for GMT time. For instance, eastern time zone is a negative five hour offset. See Fig 4.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming DST q w e q Daylight Saving Time Selection This drop down list gives four options for Daylight Saving Time: • None - When this option is selected, Daylight Saving Time is not applied at all. • By Country - When this option is selected, the Daylight Saving Time can be chosen based on country. i.e.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming Synchronization q w e r t q Input Selection y This drop-down list allows the user to select which input will control the master clock.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming IP q w e r t y u i 0.0 o a q w e r Gateway IP Address* t DHCP This drop down list allows the user to turn DHCP on or off. DHCP allows the master clock to look for an IP address on its own if the network has a DHCP server. y u Send Status to Monitor on Specified IP This setting allows the clock to send out its data in broadcast mode.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming NTP Servers q w e r t q Retry Failed-Server After moves on to the next one. w Server Addresses This field allows the user to specify which NTP servers that the master clock will try to acquire time from. Any server that is highlighted in red is not functioning after several tries.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming IP Status q w e r t y q w e r t y MAC Address IP Address Valcom This displays the MAC address for the master clock. This display the IP address for the master clock. Processor Serial Number Software Build Date Device Name The displays the serial number of the master clock. This displays the date the unit was built. This displays the device name for the master clock.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming Clock Features q w e q Display Format LED. w e Submit This button, when pressed, will save all of the information to the master clock. Cancel This button, when pressed, will clear out any changes made and will not save any data.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Web Interface Programming Database Maintenance q w e q w e Upload Database Browse File This button, when pressed, will upload the configuration of the master clock, and place it in a file for backup purposes. This button, when pressed, will allow the user to browse for the saved .db file that contains the saved events and schedules.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Support Frequently Asked Questions Can I use any SNTP server for downloading the time? Yes, any site that sends out the SNTP protocol may be used as an input to the master clock. What browsers are compatible with the master clock’s web interface? The web interface is compatible with Microsoft Internet Explorer, Mozilla Firefox, Safari, Opera and Chrome.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Support Troubleshooting The master clock will not power up. What do I do? Make sure the power cord is securely connected to the power outlet and to the back of the master clock. Upon being connected to power, the master clock should boot up instantly. There is not an on/off switch. What do I do if I cannot connect to the web interface? Verify that the IP address your attempting to access is correct.
Valcom, Inc. 5614 Hollins Road Roanoke, VA 24019 540-563-2000 P. 540-362-9800 F. www.valcom.com Compliances FCC Part 15b Industry Canada FCC Statement: Information to the user (for U.S. only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
