User guide

ManualsBrandsVADDIO ManualsHome building and DecorWallView HD1 CCU with HSDS

Installation and User Guide

Camera and Electronic Products for Integrators

pricing subject to change. Vaddio, WallVIEW, HSDS, Quick-Connect, EZIM, ProductionVIEW, PreVIEW, EZCamera and PowerRite are

registered trademarks of Vaddio. All other trademarks are property of their respective owners. Document Number 341-719 Rev. C

WALLVIEW™ CCU HD1 WITH HSDS™

Vaddio™ Quick-Connect™ CCU for

the Sony® EVI-HD1 PTZ Camera

OVERVIEW

The Vaddio WallVIEW Quick-Connect CCU (Figure 1) is built

around the Sony EVI-HD1 high definition PTZ Camera. The

WallVIEW Quick-Connect CCU HD1 allows the user to control

the color output of the camera’s image sensor, through both

Red and Blue Gain knobs, as well as Iris and Gain levels and

Aperture, to provide a higher quality image. The system uses

high speed differential signaling (HSDS), an active

transmission system that delivers low-loss, high-quality video

over Cat. 5 cabling distances up to 500 feet. The WallVIEW

Quick-Connect CCU HD1 system is capable of high definition

(HD) or standard definition (SD) resolutions in a variety of

screen configurations to fit most monitors. The EVI-HD1 is

capable of either NTSC or PAL formats.

Other features on the CCU include the ability to store settings on two discrete Scene buttons, and buttons for

Auto White Balance, One Push White Balance and Auto Iris. Like all Vaddio WallVIEW systems, the wall

mount and mounting hardware is included.

INTENDED USE

Before installing the Vaddio WallVIEW CCU Camera System, please read the entire manual thoroughly. All

Vaddio camera systems are designed for use indoors. Outdoor operation is not recommended, has not been

tested, and could damage the camera and/or create a potentially unsafe operating condition. Use only the

Vaddio PowerRite power supply provided.

SAVE THESE INSTRUCTIONS

The information contained in this manual will help you install the Vaddio WallVIEW CCU system. For

reference, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product

drawings for the Vaddio product line on the website. These documents can be downloaded from

www.vaddio.com

free of charge.

IMPORTANT SAFEGUARDS

Read and understand all instructions before using. Do not operate any electrical device if it has been

dropped or damaged. In this case, a Vaddio technician must examine the product before operating. To

reduce the risk of electric shock, do not immerse in water or other liquids and avoid extremely humid

conditions.

INFORMATION

For RS-232 control information, please see the full-length Technical Manual for the SONY EVI-HD1. This

manual can be found either on the Vaddio or Sony website. Vaddio has also prepared a number of

TechNotes, specifications and drawings designed to inform and educate integrators on the value and the

specific uses of Vaddio products.

Figure 1:

WallVIEW CCU HD1 System with

Camera, Wall Mount and EZIM CCU

Use only the power supply provided with the Vaddio WallVIEW products.

Use of an

unauthorized

ower su

will void an

and all warranties.

Summary of content (12 pages)

PAGE 1
Installation and User Guide Camera and Electronic Products for Integrators WALLVIEW™ CCU HD1 WITH HSDS™ Vaddio™ Quick-Connect™ CCU for the Sony® EVI-HD1 PTZ Camera OVERVIEW The Vaddio WallVIEW Quick-Connect CCU (Figure 1) is built around the Sony EVI-HD1 high definition PTZ Camera. The WallVIEW Quick-Connect CCU HD1 allows the user to control the color output of the camera’s image sensor, through both Red and Blue Gain knobs, as well as Iris and Gain levels and Aperture, to provide a higher quality image.
PAGE 2
WallVIEW CCU HD1 UNPACKING Carefully remove and identify the following parts for the WallVIEW CCU HD1 system: • One (1) - Sony EVI-HD1 High Definition PTZ Camera • One (1) - Vaddio EZCamera Interface Module CCU (EZIM CCU) • One (1) - Vaddio EZIM CCU to HD Break Out Cable • One (1) - Vaddio Quick-Connect CCU Universal (1-RU Rack Mountable) • One (1) - Vaddio HD1 Wall Mount • One (1) - Sony IR Remote Control • One (1) - EZCamera Control Adapter (RJ-45 to DB-9) • One (1) - 36V PowerRite Power Supply with AC C
PAGE 3
WallVIEW CCU HD1 Quick-Connect CCU Front Panel Controls (left to right): Tally Light: The blue LED tally light on the front panel is tied to the tally contacts on the rear panel allowing the user to easily track which camera interface is being used in a multi-camera system by supplying a simple contact closure (i.e. from ProductionVIEW Super Joystick or ProductionVIEW HD).
PAGE 4
WallVIEW CCU HD1 Rear Panel Connections and Controls (left to right): + G Power Supply Input: 36V 2.78 Amp power supply on a 5.5mm OD x 2.5mm ID connector. Power on RJ-45: Power is provided on a Cat. 5 cable to EZIM CCU. RS-232 IN on RJ-45: RS-232 Input from ProductionVIEW or PTZ controller. Daisy Chain control is not supported. RS-232 OUT / G/L Out on RJ-45: RS-232 and G/L outputs on Cat. 5 provide control and sync to the EZIM CCU.
PAGE 5
WallVIEW CCU HD1 INSTALLATION All WallVIEW products are specifically designed for installation on a vertical wall surface with Cat. 5 cable connectivity for Power, Video and Control signaling. Installation is simplified in that no custom 8-Pin mini-din cables or expensive S-Video plenum cables are needed and no power outlets are required near the camera bracket. All cabling is routed to the head-end using Cat. 5 cables.
PAGE 6
WallVIEW CCU HD1 Step 4: Confirm that the Cat. 5 cables are terminated correctly, by testing them with a continuity tester. Next, take the EZIM, with break-out cable connected to the 25-pin connector and fasten it to the wall mount with the supplied screws (see Figure 4, right picture). Secure the camera to the mount and using the ¼”-20 screw. Step 5: Plug the Cat. 5 cables to the appropriate ports on the EZIM.
PAGE 7
WallVIEW CCU HD1 General Specifications WallVIEW CCU HD1 Part Numbers • Sony EVI-HD1 Image Device Video Signal Effective Picture Elements Lens Focal Length Horizontal Viewing Angle Video S/N Ratio Pan/Tilt Angle WallVIEW CCU HD1 999-6307-000 (North America) WallVIEW CCU HD1 999-6307-001 (International) 1/3 type CMOS 1080i/59.94, 1080i/50, 720p/59.94, 720p/50, NTSC (LB, CR, SQ) or PAL (LB, CR, SQ) (switchable) 2 Megapixels (approximately) 10x Optical Zoom (40x with digital zoom) f=3.4 to 33.
PAGE 8
WallVIEW CCU HD1 FCC, ICES-003 Compliance and CE Declaration of Conformity For Vaddio Quick-Connect CCU and EZIM CCU products FCC Part 15 Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 9
WallVIEW CCU HD1 Appendix 1: Cable Pin-outs for the WallVIEW CCU System Quick-Connect CCU Pin-out Assignments: POWER CONTROL & EXT. SYNC CAMERA + G 36V 2.
PAGE 10
WallVIEW CCU HD1 EZIM CCU Pin-out Assignments Power Connector RJ-45 Signal Pin 1) Power + 2) Power 3) Power + 4) Power 5) Power + 6) Power 7) Power + 8) Power - EZIM CCU G/L GAIN RS-232 IN/ VIDEO G/L IN 12345678 RS-232 IN Connector Signal - RS-232 Pin 1) Not Used 2) Not Used 3) Not Used 4) G/L+ 5) G/L GND 6) GND 7) RXD (from TXD) 8) TXD (to RXD) Video Connector RJ-45 Signal Pin SD 1) CVBS + 2) CVBS GND 3) Y+ 4) C+ 5) C GND 6) Y GND 7) Not Used 8) Not Used POWER 12345678 HD CVBS + CVBS GND Y+ PB+
PAGE 11
WallVIEW CCU HD1 WARRANTY INFORMATION Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants this product against defects in materials and workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio receives notice of such defects during the warranty period, they will, at their option, repair or replace products that prove to be defective.
PAGE 12
WallVIEW CCU HD1 9433 Science Center Drive, Minneapolis, MN 55428 Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464 www.vaddio.com ©2008 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing subject to change. Vaddio, WallVIEW, HSDS, Quick-Connect, EZIM, ProductionVIEW, PreVIEW, EZCamera and PowerRite are registered trademarks of Vaddio. All other trademarks are property of their respective owners.