Manual

ManualsBrandsVaddio ManualsAudioWallVIEW 100 Technical

 2001 Sony Corporation

Color Video Camera

EVI-D100/D100P

A-AYT-100-11 (1)

Technical Manual

Summary of content (48 pages)

PAGE 1
A-AYT-100-11 (1) Color Video Camera Technical Manual EVI-D100/D100P  2001 Sony Corporation
PAGE 2
Table of Contents Features ..................................................................... 3 Connection ................................................................. 4 Locations of Controls ............................................... 5 Basic Functions ......................................................... 7 Overview of Functions ................................................ 7 Initial Values and Backup ......................................... 11 Memory (Position preset) Function .......
PAGE 3
Overview Features • The CCD features 380,000 effective picture elements for the EVI-D100 and 440,000 for the EVI-D100P, which enables high-resolution shooting. • In addition to high-speed pan/tilt action, improvement of the noise reduction mechanism lets you use the Color Video Camera for a variety of purposes. • VISCA lets you operate your Color Video Camera from a computer. • Up to six combinations of the camera's position and status can be memorized. • A multi-function Remote Commander is provided.
PAGE 4
Connection Connection Video cable (not supplied) to Video input to VIDEO S-Video cable (1-751-416-11 not supplied) to S VIDEO to S-Video input VISCA cable (not supplied) 1) to RS-232C to VISCA IN Computer, TV or VCR with a video input jack to VISCA OUT To VISCA IN of other EVI-D100/Ps (when connecting to more than one camera) AC power adaptor MPA-AC1 (supplied) to AC outlet to DC IN 12V Power cord (supplied) 1) When the camera is connected to a computer with a VISCA cable (RS-232C, cross type), yo
PAGE 5
Locations of Controls Locations of Controls Main Unit Front 3 4 1 2 Bottom Rear ON qs 1 2 qd qf 5 6 7 1 POWER lamp 2 STANDBY lamp 3 Lens 4 Sensor for the remote commander 5 BACKUP switch 6 VIDEO jack 7 S VIDEO jack 8 IR SELECT switch 9 DC IN 12 V jack 8 9 q; qa 0 VISCA OUT jack qa VISCA IN jack qs IR SELECT switch Set this switch to ON to allow the camera output signals transmitted from the Remote Commander to the Color Video Camera via the VISCA OUT jack to be output.
PAGE 6
Locations of Controls Remote Commander 3 L UA AN 2 GH T M CK LI 7 3 6 R ES ET 2 5 ST D P RE AN SE -TI T LT PA N -T IL T 9 FA ST HO M E PR ES ET 4 1 PO SI TI O N SC TA DA 3 8 R EV RE 2 EN AU TO FA R BA 1 1 FO C U S N EA R C AM ER A SE LE C T PO W ER 6 M 0 1 CAMERA SELECT buttons 2 FOCUS buttons AUTO button FAR button NEAR button MANUAL button 3 DATA SCREEN button 4 PAN-TILT button Arrow buttons HOME button 5 L/R DIRECTION SET button 6 POWER switch W DIR 5 EC L
PAGE 7
Basic Functions Basic Functions Overview of Functions Zoom The EVI-D100/P uses an 10× optical zoom lens. And its digital zoom function allows you to zoom up to 40×. • Optical 10×, f = 3.1 to 31 mm (F 1.8 to F 2.9) The horizontal angle of view is approximately 65 degrees (wide end) to 6.6 degrees (tele end). Digital zoom increases the picture element size and reduces the resolution.
PAGE 8
Basic Functions 1) The One Push White Balance mode is a fixed white balance mode that may be automatically readjusted only at the request of the user (One Push Trigger), assuming that a white subject, in correct lighting conditions, and occupying more than 1/2 of the image, is submitted to the camera. Selecting the One Push White Balance mode recalls the white balance data computed at the last One Push Trigger, if the BACKUP switch is set to ON and the camera has been connected to an AC outlet.
PAGE 9
Basic Functions AE – Gain priority The gain can be set freely by the user to 8 steps between –3 dB and +18 dB. The shutter speed is fixed and the iris is set automatically, according to the brightness of the subject. Data Iris Gain Data Iris Gain 17 F1.8 18 dB 0B F4.8 0 dB 16 F1.8 15 dB 0A F5.6 0 dB 15 F1.8 12 dB 09 F6.8 0 dB 14 F1.8 9 dB 08 F8 0 dB 13 F1.8 6 dB 07 F9.6 0 dB Data Setting value 12 F1.8 3 dB 06 F11 0 dB 07 18 dB 11 F1.
PAGE 10
Basic Functions Exposure Compensation Digital Effect Exposure compensation is a function which offsets the internal reference brightness level used in the AE mode, by steps of 1.5 dB. Digital Effect consists of the following functions. They are all executed via the field memory. • Still: Moving Image on Still Image • Flash: Continuous Still Image • Lumi.: Moving Images on Binaried Still Image • Trail: Afterimage Lag of Moving Subject Data Step Setting value 0E 7 10.5 dB 0D 6 9 dB 0C 5 7.
PAGE 11
Basic Functions Initial Values and Backup Initial values of functions of the EVI-D100/P are indicated in the “Initial values” column. An a in the “Backed up/Not backed up” column indicates that the setting is memorized in the camera. An × indicates that it is not.
PAGE 12
Basic Functions Memory (Position Preset) Function You can save the camera settings and pan/tilt position using the supplied Remote Commander or the VISCA commands. Six channels are available.
PAGE 13
× × × × × × × × a × InquiryCommand (etc.) a a a a a a a a a a a a a a Other status 1) RC: Remote Commander D-Zoom On/Off Zoom Direct Zoom Tele/Wide/Stop Command RC VISCA Mode × × × × OFF Power × × × × Initializing Mode Condition 2 (Zoom) × × × × IFC × a a a a a VISCA a a a a RC1) Tele/Wide adjustment × × On Freeze 1) Initializing: The period from the instant you connect the camera to an AC outlet to the instant the camera outputs a video signal.
PAGE 14
RC VISCA × × × × × × × × OFF Power × × × × × × × × Initializing × × × × × × × × IFC R/B Gain Reset/Up/Down/Direct One Push WB Trigger Auto/Indoor/Outdoor/ OnePushWB/ATW/Manual White Balance mode setting Command Mode × × × × × Initializing × OFF Power × × × IFC Mode Condition 4 (White Balance) Focus Near Limit AF Sens High/Low Focus Infinity One Push AF Trigger Focus Mode Auto/Manual Focus Direct Focus Far/Near/Stop Command Mode Mode Condition 3 (Focus) × × × Freeze On ×
PAGE 15
× × × × × × × × × Gain Reset/Up/Down/ Direct Bright Reset/Up/Down/ Direct ExpComp On/Off ExpComp Reset/Up/Down/ Direct 3) Back Light On/Off × × × × × × × × × × IFC × × × × × × × × × × On Freeze × × × × × × × × × × Recall execution Memory 1): a only when the AE mode turns “Shutter Pri” into “Bright” 2): While activating a Digital Effect function, you cannot set functions related to Slow Shutter.
PAGE 16
Datascreen On/Off Digital Effect Level Off/Still/Flash/Lumi.
PAGE 17
Common Memory Reset × × × × × × × × × × × × × × × × × × × × × × × × × × × × × Initializing × Power OFF 1): a while the camera operates in the Tele/Wide zoom mode 2): a while the camera operates in the Far/Near focus mode RC VISCA Common Memory Set Memory Recall VISCA VISCA Pan-tiltDrive LimitSet RC VISCA Pan-tiltDrive LimitClear Pan-tiltDrive Reset RC VISCA VISCA Pan-tiltDrive RelativePosition Pan-tiltDrive Home VISCA VISCA Pan-tiltDrive Stop RC VISCA Transmit device Pan-tilt
PAGE 18
Command List Command List VISCA1)/RS-232C Commands Use of RS-232C control software which has been developed based upon this command list may cause malfunction or damage to hardware and software. Sony Corporation is not liable for any such damage. Overview of VISCA The address of the controller is fixed at 0. The addresses of the peripheral devices are 1, 2, 3 ... in order, starting from the one nearest the controller.
PAGE 19
Command List VISCA Communication Specifications VISCA packet structure The basic unit of VISCA communication is called a packet (Fig. 2). The first byte of the packet is called the header and comprises the sender’s and receiver’s addresses. For example, the header of the packet sent to the EVI-D100/P assigned address 1 from the controller (address 0) is hexadecimal 81H. The packet sent to the EVI-D100/P assigned address 2 is 82H.
PAGE 20
Command List Responses for commands and inquiries Command execution cancel ● ACK message Returned by the EVI-D100/P when it receives a command. No ACK message is returned for inquiries. To cancel a command which has already been sent, send the IF_Clear command as the next command. To cancel one of any two commands which have been sent, use the cancel message. ● Completion message Returned by the EVI-D100/P when execution of commands or inquiries is completed.
PAGE 21
Command List VISCA Device Setting Command Before starting control of the EVI-D100/P, be sure to send the Address command and the IF_Clear command using the broadcast function. For VISCA network administration ● Address Sets an address of a peripheral device. Use when initializing the network, and receiving the following network change message. ● Network Change Sent from the peripheral device to the controller when a device is removed from or added to the network.
PAGE 22
Command List Pin assignment • EVI-D100/P 1. DTR 1. CD 2. DSR 2. RXD 3. TXD 3. TXD 4. 5. 6. 7. 8. 4. 5. 6. 7. 8. 9. GND RXD GND IR OUT N.C. • EVI-D100/P 8 7 6 5 4 3 2 1 Windows D-sub 9 pin DTR GND DSR RTS CTS RI EVI or Macintosh 1. DTR 1. DTR 2. 3. 4. 5. 6. 7. 8. 2. 3. 4. 5. 6. 7. 8. DSR TXD GND RXD GND IR OUT N.C.
PAGE 23
Command List VISCA Command/ACK Protocol Command Command Message Reply Message Comments General Command 81 01 04 38 02 FF (Example) 90 41 FF (ACK)+90 51 FF (Completion) 90 42 FF 90 52 FF Returns ACK when a command has been accepted, and Completion when a command has been executed. 81 01 04 38 FF 90 60 02 FF (Syntax Error) Accepted a command which is not supported or a command lacking parameters.
PAGE 24
Command List VISCA Camera-Issued Messages ACK/Completion Messages Command Messages Comments ACK z0 4y FF (y:Socket No.) Returned when the command is accepted. Completion z0 5y FF (y:Socket No.) Returned when the command has been executed. z = Device address + 8 Error Messages Command Messages Comments Syntax Error z0 60 02 FF Returned when the command format is different or when a command with illegal command parameters is accepted.
PAGE 25
Command List EVI-D100/P Commands EVI-D100/P Command List (1/4) Command Set Command Command Packet Comments AddressSet Broadcast 88 30 01 FF IF_Clear Broadcast 88 01 00 01 FF 8x 2p FF p: Socket No.
PAGE 26
Command List EVI-D100/P Command List (2/4) Command Set Command Command Packet Comments CAM_BGain Reset 8x 01 04 04 00 FF Manual control of B Gain Up 8x 01 04 04 02 FF Down 8x 01 04 04 03 FF CAM_AE CAM_SlowShutter CAM_Shutter CAM_Iris CAM_Gain CAM_Bright CAM_ExpComp CAM_BackLight Direct 8x 01 04 44 0p 0q 0r 0s FF pqrs: B Gain 0000 to 00ff, 256 steps Full Auto 8x 01 04 39 00 FF Automatic exposure mode Manual 8x 01 04 39 03 FF Manual control mode Shutter Priority 8x 01 04 39 0A F
PAGE 27
Command List EVI-D100/P Command List (3/4) Command Set Command Command Packet Comments CAM_Aperture Reset 8x 01 04 02 00 FF Aperture control Up 8x 01 04 02 02 FF Down 8x 01 04 02 03 FF Direct 8x 01 04 42 0p 0q 0r 0s FF pqrs: Aperture Gain 0000 to 000f, 16 steps, Initial value: 5 Off 8x 01 04 60 00 FF Wide mode setting Cinema 8x 01 04 60 01 FF CAM_Wide CAM_LR_Reverse 16:9 Full 8x 01 04 60 02 FF On 8x 01 04 61 02 FF Off 8x 01 04 61 03 FF CAM_Freeze On 8x 01 04 62 02 FF Off 8x
PAGE 28
Command List EVI-D100/P Command List (4/4) Command Set Command Command Packet Comments Pan-tiltDrive Up 8x 01 06 01 VV WW 03 01 FF VV: Pan speed 01 to 18 Down 8x 01 06 01 VV WW 03 02 FF WW: Tilt Speed 01 to 14 Left 8x 01 06 01 VV WW 01 03 FF YYYY: Pan Position FA60 to 05A0 (center 0000) Right 8x 01 06 01 VV WW 02 03 FF ZZZZ: Tilt Position FE98 to 0168 (center 0000) UpLeft 8x 01 06 01 VV WW 01 01 FF UpRight 8x 01 06 01 VV WW 02 01 FF Pan-tiltLimitSet DownLeft 8x 01 06 01 VV WW 01 02 F
PAGE 29
Command List EVI-D100/P Inquiry Command List (1/2) InquiryCommand CommandPacket InquiryPacket Comments CAM_PowerInq 8x 09 04 00 FF y0 50 02 FF On y0 50 03 FF Off (Standby) CAM_AutoPowerOffInq 8x 09 04 40 FF y0 50 0p 0q 0r 0s FF pqrs: PowerOff Timer CAM_DZoomModeInq 8x 09 04 06 FF y0 50 02 FF Digital Zoom On y0 50 03 FF Digital Zoom Off CAM_ZoomPosInq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqrs: Zoom Position CAM_FocusModeInq 8x 09 04 38 FF CAM_FocusPosInq 8x 09 04 48 FF CAM_AFModeI
PAGE 30
Command List EVI-D100/P Inquiry Command List (2/2) InquiryCommand CommandPacket InquiryPacket Comments CAM_ExpCompModeInq 8x 09 04 3E FF y0 50 02 FF On y0 50 03 FF Off CAM_ExpCompPosInq 8x 09 04 4E FF y0 50 0p 0q 0r 0s FF pqrs: ExpCompPosition CAM_BackLightModeInq 8x 09 04 33 FF y0 50 02 FF On y0 50 03 FF Off CAM_ApertureInq 8x 09 04 42 FF y0 50 0p 0q 0r 0s FF pqrs: Aperture Gain CAM_WideModeInq 8x 09 04 60 FF CAM_LR_ReverseModeInq 8x 09 04 61 FF CAM_FreezeModeInq 8x 09 04 62 F
PAGE 31
Command List EVI-D100/P Block Inquiry Command List Lens control system inquiry commands (1/2) .......
PAGE 32
Command List Lens control system inquiry commands (2/2) .......
PAGE 33
Command List Camera control system inquiry commands (1/2) ..
PAGE 34
Command List Camera control system inquiry commands (2/2) .. Command Packet 8x 09 7E 7E 01 FF Byte 12 Bit Comments 7 0 6 0 5 0 4 0 3 0 2 1 Gain Position 0 13 7 0 6 0 5 0 4 3 2 Bright Position 1 0 14 7 0 6 0 5 0 4 0 3 2 1 Exposure Comp.
PAGE 35
Command List Other inquiry commands (1/2) ................................ Command Packet 8x 09 7E 7E 02 FF Byte 0 1 2 Bit Bit Comments 7 7 0 6 6 0 4 5 5 0 4 0 y0 3 6 3 0 2 2 Digital Effect Mode 1 1 0:Off 1:Still 2:Flash 3:Lumi.
PAGE 36
Command List Other inquiry commands (2/2) ................................
PAGE 37
Command List VISCA Command Setting Values NTSC Bright Exposure control NTSC Shutter Speed Iris Gain PAL 13 10000 10000 12 6000 6000 11 4000 3500 10 3000 2500 0F 2000 1750 0E 1500 1250 0D 1000 1000 0C 725 600 0B 500 425 0A 350 300 09 250 215 08 180 150 07 125 120 06 100 100 05 90 75 04 60 50 03 30 25 02 15 12 01 8 6 00 4 3 11 F1.8 10 F2 0F F2.4 0E F2.8 0D F3.4 0C F4 0B F4.8 0A F5.6 09 F6.8 08 F8 07 F9.
PAGE 38
Command List Zoom values and focal length (for reference) Zoom values Focal length1) (mm) 0000h 3.1 0E6Dh 4.65 188Eh 6.2 2507h 9.3 2B82h 12.4 3130h 15.5 352Eh 18.6 385Dh 21.7 3B48h 24.8 3E01h 27.9 4000h 31 5000h 41.
PAGE 39
Command List Lens control 0000 (Optical Wide end) to 4000 (Optical Tele end) 4000 (Digital Zoom ×1) to 7000 (Digital Zoom ×4) Focus Position 1000 (Far) to 8400 (Near) Focus Near Limit 1000 (Far) to 8400 (Near) Zoom Position Note: The lower one byte is fixed at 00. Others R,B gain 00~FF Aperture 00~0F Effect Level (Digital Effect Level) STILL 00~20 FLASH 00~18 LUMI.
PAGE 40
Command List D30/D31 Mode Overview Switching the Mode The D30/D31 mode allows you to control the EVID100/P using VISCA commands for the EVI-D30/ D31. Most of the VISCA commands for the EVI-D100/P correspond to one for the EVI-D30/D31. However, some of the VISCA commands for the EVI-D100/P are different from those for the EVI-D30/D31 in definitions of parameters.
PAGE 41
D30/31 Mode Command List Accepting or Sending Back Commands When accepting commands Type of command D30/D31 mode on Common to both the D30/D31 and Common parameters Accepts as is D30/D31 mode off D100/P Different parameters Translates the D30/D31’s parameters to those of the D100/P Accepts as is CAM_Memory Reset Memorized data items are erased and camera settings return to initial values Memorized data items are erased Refuses and sends back the Accepts as is Only for the D100/P NotExecutable
PAGE 42
D30/31 Mode Command List Translating Parameters Zoom speed Focus position Cameras Parameters EVI-D30/D31 1000h (FAR) to 9FFFh (NEAR, 1 cm) EVI-D100/P 1000h (FAR) to 8400h (NEAR, 10 cm) Translation of commands Cameras Parameters EVI-D30/D31 02h (Min. speed) to 07h (Max. speed) Accepted parameters Translation EVI-D100/P 00h (Min. speed) to 07h (Max.
PAGE 43
D30/31 Mode Command List Shutter speed Translation of commands The EVI-D100/P translates the D30/D31’s parameters to D100/P parameters in accordance with the table below.
PAGE 44
D30/31 Mode Command List Pan/tilt speed The actual speed that is defined by the parameters corresponds to that of the EVI-D30/D31. When the camera accepts commands such as PantiltDrive Home, Reset, or CAM_Memory Recall, the operation speed is equal to the speed when the D30/ D31 mode is OFF. Pan Tilt Speed (deg/sec) Speed (deg/sec) Parameters D100/P D30/D31 Parameters D100/P 01h 2.0 b 3.3 01h 2.0 b D30/D31 2.5 02h 2.4 b 6.7 02h 2.4 b 5.0 03h 3.0 b 10.0 03h 3.0 b 7.5 04h 3.
PAGE 45
D30/31 Mode Command List Pan/tilt position Translation when answering inquiry commands The camera sends back values that are calculated by inverse conversion performed when the camera accepts commands. Pan position Cameras Parameters EVI-D30/D31 FC90h (–100 degrees) to EVI-D100/P FA60h (–100 degrees) to 0370h (+100 degrees) Note Repetitive use of the Relative position command may increase the variance that is accumulated from translation.
PAGE 46
Specifications Specifications System Video signal EVI-D100: NTSC Color, JEITA standards EVI-D100P: PAL Color, CCIR standards Picture element 1/4 inch color CCD (Total picture elements: EVI-D100: Approx. 410,000 EVI-D100P: Approx. 470,000) (Effective picture elements: EVI-D100: Approx. 380,000 EVI-D100P: Approx. 440,000) Lens 10× (Optical), 40× (Digital) f=3.1 to 31 mm, F1.8 to F2.9 Horizontal angle: 6.
PAGE 47
Specifications Dimensions 87.5 (3 7/16) 1.7 (1/16) 132 (5 3/16) 136.5 (5 3/8) Tripod hole 1/4-20UNC (ISO1222) Bottom 113 (4 7/16) 116.5 (4 19/32) Top 20 (25/32) 113 (4 7/16) 128 (5 1/32) Right side 120 (4 23/32) Front φ 4.5 (3/16) 44.4 (1 3/4) 94.
PAGE 48
Specifications Precautions Software Other Use of the demonstration software developed by Sony Corporation or use of the software with customer developed application software may damage hardware, the application program or the camera. Sony Corporation is not liable for any damages under these conditions. Do not apply excessive voltage. (Use only the specified voltage.) Otherwise, you may get an electric shock or a fire may occur.