Vehicle 4-CH DVR System USER MANUAL 3G Module Without 3G Module 2012 Optional MAR V1.
Index A. Product Features .................................................................................................1 B. Specification.........................................................................................................2 C. Product Appearance ............................................................................................3 D. Record / Stop-Record ..........................................................................................7 E.
A. Product Features Max. up to 4 CH vehicle cameras, can take record for inside and outside the vehicle. Video output for live view, playback with monitor. H.264 Compression format. Recording format：D1 and CIF. Build-in single channel microphone. Quick Search Overall Event Log. The full recording time and date can be showing in the monitor directly. Auto-Record after memory card Plug-in and Power Supplied.
B.
C. Product Appearance Front Panel Extending IR Lead CF 1 CF 2 GPS Indicator LED(CF2) IR Receiver Record Indicator LED(CF1) Power Indicator LED Rear Panel TYPE1: without 3G module Video Input Video Output USB GPS(optional) Audio Output Power Input DC 8-28V Harness Connector Alarm Input 1. DC+12V output 2. Signal and general DC grounding 3. Signal and general DC Video Output Audio Input / Output Harness Connector: Assorted cable includes 4 set of image input, power core and S connector.
Wiring Diagram A B C A. Alarm input / Audio input/output Alarm input (Alarm trigger off signal +12~28V) 1. alarm input 1 2. alarm input 2 3. alarm input 3 4. alarm input 4 5. ground wire Audio output/input 1. ground wire 2. Audio output 3. ground wire 4.
B. Harness Connector DC12V OUT / VIDEO IN 1. 2. 3. 4. video input 1 video input 2 video input 3 video input 4 C. Power input/output 1. DC+12V output 2. Signal and general DC grounding 3. Signal and general DC grounding 4. DC8~28V IN car power input (positive electricity) 5. ACC starter control 6.
3G USB Module Dimension (UNIT: mm) 6
D. Record / Stop-Record Record Indicator LED(CF1) Power Indicator GPS Indicator LED(CF2) 1. Power on / Record Turn on the power, and it will take approximately 40 seconds to boot up. During the recorder booting up, the CF card indicator LED will start flashing as the recording is in progress. Light indicator: ● Red light: light on, means power on; light off, means no power/power off. ● Yellow light: light flashing, means CF take recording; light off means non-recording.
E. System Operating Instruction Vehicle DVR system provides two operational methods: IR remote controller and PC software application. 1. Through IR Remote Controller Instruction 1.1 As following is the key mapping table for IR Remote controller: CH2 display CH1 display Record CH3 display CH4 display Quad display Menu Mute Up、Down、Left、Right Enter Fast Forward Fast Rewind Stop Play Step/Pause 1.
◆IR Remote controller Instruction (1) Select Item: [up/down/left/right] (2) Change setting for selected item: [up/down/left/right] (3) Change setting for Bar item：[Enter] (4) Full Screen display for each CH: [CH1~CH4] (5) Open OSD menu, back to previous page：[menu] (6) Quad display ：[Quad] (7) Enter playback mode ：[play] (8) Stop Play/exit playback mode：[Stop] (9) Suspend recording:[Pause] System Setup instruction (1) Set Encode Parameter IR Remote controller operating instruction (1) Can be selected R
(2) Left/Right key→ Set brightness/contrast/hue for current channel (Left key→ To reduce)/ (Right key→ To increase) Item Setting (1) Brightness: (Left key→ to reduce)/ (Right key→ to increase) (2) Contrast: (Left key→ to reduce)/ (Right key→ to increase) (3) Hue: (Left key→ to reduce Hue)/ (Right key→ to increase Hue) (3) Set Time IR Remote controller operating instruction (1) Up key→ Plus one , Down key→ Reduce one. (2) Left key→ Left one space, Right key→ Right one space.
(5) Delete All Record Data (Format Disk) (1) Delete All Record Data Use right key or left key to select the selection then click “enter” to confirm. ★Caution! All data will be deleted when you click “Yes”. (6) Default Live View Channel Display (1) Select the default live view CH after startup: Item selected will be default live view display mode after DVR booting completed. (2) On this page, Use left key or right key to select Quad display (Multi-CH) or CH 1 Display, then press “enter” to confirm.
(8) Firmware Update (1) During firmware update, please do not power off; after finished the DVR will reboot automatically. (2) When update firmware, Using left/right button on remoter controller to select Yes/No for update, then press enter button to confirm. ★ Must use CF card for firmware update. (9) Check Firmware Version (1) To check current firmware version, please select version and press enter key. ★ Check the current firmware version first before firmware upgraded.
(11) 3G Networking Setting (Only available when DVR with specific 3G module) (1) When enable the 3G networking function, Press the right/left key on remote controller first to select 3G ON/OFF, then press “confirm” key to save the change. ★ After setup finished, press the up/down key to check information about 3G network settings are properly. (12) Alarm setup (1) When the alarm is triggered, the screen should display which CH is triggered.
★Alarm system works only after finishing both hardware and software setting. Ex. It could apply to switch CH to full screen mode for driver when backward of parking or using turn signals to prevent blind corners. 1 CH Input reverse signal G It could connect with the second and third black wire.(share ground wire with automobile) ★When the alarm is triggered, the screen switch to full display which CH is triggered. And It will return to quad display when alarm is finished.
(13) Password Setting (3G version without this function) (1) Set password protected on machine： It required to enter the password before setting, playback, formatting… implement relevant actions. (2) Use remote controller keys to change setting, Click Left key to move one space for selecting number for password, then click up/down key to enter the number, after finished, click “enter” key to confirm. (You can select number 0~9 for the password.
LIVE Display (1) Select CH1~CH4 to full display mode; If you want to return to quad display, please press quad key. (2) On Live view mode, click “menu’ to enter OSD menu or click ‘Play” to enter playback mode. ★ If it shows the “G” mark on Upper right screen, it means GPS positioning successes. Playback mode Use remote controller to enter playback menu. (1) Select CH1~CH4 as full display for each CH; If you want to return to quad display, please press quad key.
2. Through Carbox Player on PC Site (1) Use CF card to playback directly Execute the CarBox2.exe from CD-ROM , the display as showing below. Click Play button to select memory card; to choose the files from memory card or or click open file hard disk, and then double-click the file you want to play. Under playing mode the play key will switch to pause key. ★Caution: It needs to install DirectX 9.0 or above before running CarBox2 software.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 Previous File Previous Frame Backward Play Pause Stop Play Next Frame Next file Open folder, select file. Disk backup. Select the backup path for file storage. Google Map Configuration Snapshot Tool, CF card format, language setting. Hard Disk Backup Review footage on the CF card through PC, Click” ”, then it will pop-up as following backup dialogue windows.
Step 1. Select the CF card drive no. Step 2. Select the recorded file which you want to backup Step 3. Select the Backup Format Backup format: (1)Original CF card format backup. XXXX*.sd file (2)AVI File(*.avi) backup when take this format as backup. CHN01 for front view camera image file, file type: *.avi ★caution: The difference between original CF card format file and AVI file is that AVI file contains only video and audio data but lose the GPS coordinates, speed and G-sensor data.
Step 5. Backup: Click ‘backup’ to start saving the file to your specified destination Configuration Before using the machine, please insert the CF card to card reader and connect to the PC to start setting. After setting, you can insert the card back to DVR and start recording.
5 Audio Recording Audio recording on or off. This function can encrypt the data and prevent others from accessing. Maximum letters:15 letters. Example: 123456789123456 6 After setting the password up, you have to input password every time for playing the files, modify the setting, formatting the memory card etc. Password ★ Note: Please check if you have set capital letters for your password and save your password well in other place to prevent from missing. You can set up the speed unit here.
Snapshot While playing the recorded file, you can use this function to snapshot the picture and save it into your PC. Default saving path for snapshot picture will be in x:\IBoxPlayer/Snapshot folder. File type: .bmp b. Latitude & Longitude Coordinates Position Latitude & Longitude c. G Sensor G-sensor: Detect & record G-force data. G SENSOR (1) X: The G-force from left & right of the car. (2) Y: The G-force from front & back of the car. (3) Z: The G-force from upside & downside of the car d.
e. Video Search & Play Speed Video searching BAR Play speed (1) Video Searching: You can use the mouse to drag the bar to search the video quickly. (2) Play Speed: Support 2x, 4x fast forwarding and -2x, -4x slow play mode. f. Volume Control Volume BAR Volume degree Volume BAR: Click the left button of mouse control to adjust the volume degree. (2) 3G client software for viewing directly(select models with 3G modules) Executive Playback software “3G ClientApp.
Note: To perform this software will require DirectX 9.0 or more. Click and then select the name of vehicle to view the image (example, the figure of 175) then click on Channel-01 (or other Channel) and then hold down the left mouse button and drag to the split screen in right side. The other method to choose split-screen first and then click on Channel-01 with right key of the mouse, click PLAY function to view real-time image. (When the icon becomes , it means the vehicle that is currently offline.
Click records... can watch the event log and vehicle driving Click can watch the Google Map and inquiry the date and time record of the vehicle…..
3G ClientApp page and other relevant settings 1. Login: click Login on the top of the screen to open the login screen information. 2. Add Device: In order to identify each device, add the vehicle information here. 3. Style: watch different split-screen, just click Style option to set values; Total 1 * 1, 2 * 2, 3 * 3, 4 * 4, 4 types of split screen to choose. F. Format Memory Card When should you「format」the CF CARD? When the used CF card or just a new card, you should format CF card first before use.
a. b. c. d.
5. After formatting completed, re-insert the CF card to do relative setting. please insert the card into DVR for recording. █Process to Format the CF Card on DVR: 1. Use remote controller to enter DVR menu and choose Delete All the Record Data(format disk). 2. Select “Yes” and Click “Enter’’ to start formatting. 3. When the screen back to LIVE mode ,the formatting is completed. G.
3. Execute the player “CarBox2.exe” into main page(refer ) to the charts below 4. Select restore button to start as following steps a. b. c.
e. d. f. 5. You can use the memory card for other purposes.
H. Installation and setting up for 3G module Please confirm 3G system with the telecom provider in local area, and choose appropriate module to fit in with. Telecommunication Norm: WCDMA 3G Network Card:EM770W Telecommunication Norm: CMDA2000 3G Network Card: EM660 1. Installation Guide for 3G module a. Take off two screws from front and back cases as red mark; please remove upper cover from this device.
Installation interface for SIM card and 3G module.
b. Installation process for EM770W of HUAWEI 3G Module (SIM card shell be purchased by customer) i. Disable PIN code from SIM card by mobile phone firstly and insert this card into the device. 1. Insert SIM card into the slot 2. Flat the SIM card and push into the buttom then locked ii. Start to install of 3G module after SIM card installation. 1. Slanting insert the 3G module into PCI-E slot. 2. Push the 3G mould on flat status and lock two pieces of M2 screws. 3.
2. a. b. 3G INTERNET SETTING Please confirm whether the code number is closed or not. Confirm if The Telecommunication providers’ APN is the same with Dial-Up Number’s information, if not, please follow all 3G Config Tool setting file steps. and open the setting i. Please double click page as below: The explanation for setting up: 1. UserName: No need in common 2. Password: No need in common 3.
4. 5. 6. 7. Server IP Address is 61.221.66.200 Server Port: Default Sever Port is 13579, Not recommend to change the original setting). APN: 3G APN, generally preset to be Taiwan Telecommunication providers, if in other area, Please check local Telecommunication providers offered APN setting name.) Dial-Up Number: 3G Dial-Up Number, generally preset to be *99#, if in other area, Please check local Telecommunication providers offered 3G Dial-Up SETTING Numbers.
iv. And Please put your USB FLASH DRIVER into the SA-650-CF USB connecting Port, and re-connect the battery again. v. After re-start, please pick the 3G internet item up in contents to confirm whether the 3G information updating successful or not. When updating successfully, all the updating information would shown on the 3G module related web information.
I. Record Time Estimation (Based on constant record mode with 8GB card) ＊The chart of estimated record time listed below is for reference only(based on 8Gb with 2 inner &2 exterior Cameras). The length of time recorded can be varied due to different record condition. Unit: Hr Resolution/ fps Video Quality High Normal Low D1 CIF 5 fps 10 fps 15 fps 5 fps 10 fps 15 fps 20 fps 25 fps 30 fps 9.5 4.2 3.1 15 13.3 8.5 8 7.5 7 12 6.7 6.3 18 14.3 9 8.3 8.1 7.5 16.8 7.2 12 20 17.
