6 / 36 / 64 CH Linux NVR Network Video Recorder User’s Manual Network video recording system 2013 OCT V1.
Notice before use This authorization agreement of client’s software/hardware is legally effective to you(individual or single machine) and our company. This agreement covers components of software/hardware, media, print, online publication and electronic files. All the application through installation, duplication or the other way must be based on this agreement. If you disagree with the terms of this agreement, please don’t install or use this product.
Terms and Conditions The overall risk, is that arising out of the use or performance of software and hardware products. This product will be informed, such as when it is used with certain device or other hardware, may enable you to carry out surveillance and data processing, which may be subject to or in violation of applicable law, which includes but is not limited to data privacy, and criminal law. Please check your use to comply with applicable laws is the responsibility of users themselves.
CONTENTS Foreword 【Notices】 ........................................................................................................................ 1 I.【Specification List 】....................................................................................................................... 2 II.【Read before use】 ......................................................................................................................... 4 III.【Installation manual】..............................................
Foreword 【Notices】 WARNING Do not expose the DVR under the sunlight, heat or wet environment while installation. As it could decrease the performance of DVR and damage the machine. Do not touch the power plug or case with wet hands as this could result electric shock. Do not forcedly bend or put heavy object on power cable as this could result in injury to personal or equipment.
I. 【Specification List 】 Hardware Specification Processor Memory HDD Capacity Intel® Core™CPU Core i5 3470 4GB DDR3 RAM,1GB Flash(DOM) Storage: Maximum 2 x 3.5" SATA HDD,1 x 5.25" drive bay One 2T HDD included(support for 3T) Lan Port LED Indicators USB Buttons 1 x Gigabit RJ-45 Ethernet Port HDD, Power, Network LEDs 6 x USB 2.
Playback Control speed control Convert multiple recording files to the external USB device Export Remote Play, pause, stop, reverse play, next/ previous video file, different instantly Display Mode Split-screen display model for 1, 4, 9, 16, 25, 36, 49 or 64 channels.
II. 【Read before use】 2.1 Front panel introduction： 1. 2. 3. 4. 5. Hidden hard drives (built-in 2T) Indication light of hard drives. Indication light of power supply. Switch on button of system 5.25 inch installation device; expandable CD burner(reserved) 2.2 Rear panel introduction： 1. 2. 3. 4. 5. 6. 7. 8. USB2.0 port x 6 P/S2 port(can be accessed by keyboard or mouse) D-Sub DVI HD Out RJ-45 Audio output hole. Power input.
III. 【Installation manual】 1． At the first turn-on, if fail to enter, please select SATA DOM as the first prior turn-on device in BIOS. 2． At the first entrance into system, if tip for HDD formatting, when you need recording, please click “yes”, if no need, please click ”no”. Notice! After HDD formatting, the existing DATA will be non-recoverable. If no tip, it indicates the HDD has been formatted before shipment.
IV. 【Software instruction】 1. Login After installation and restart to enter the operation interface, if you proceed any operation, system will pop-up the dialogue box to tip login (some version will default and not to tip.
V. 【NVR function description by area】 1， exit（exit system，auto power off） 2， channel switch option（1，2，4，9，16，25，36 channel switch） 3， the video display area（select the corresponding camera, double-click for amplification of single channel and return to multi-screen） 4， tool bar menu (enter system setup, camera setting, network setting, option of playback control., etc.
VI. 【Set-up of interface operation】 6.1 System Setup 6.1.1 General Setup: Click the setting button to enter setting interface. You may setup the flow time of video loss, alarm/audio alarm ; setup the shift time length of video image switch; start the loop video to set up the restart time each day; camera can switch to simple Chinese, traditional Chinese and English; you can choose PAL or NTSC.（REMARK: mode switch of PAL/NTSC needs to reboot）click on apply to save.
6.1.2 Date/ Time Setup Set the current time, and then save it. Refer to the following figure. 6.1.3 Network Time Setup: Start auto calibration and setup the server address, port, time intervals and then click on “apply”, “immediate calibration”. And then click return.
6.1.
6.1.5 Version information Enter to find the current software version. You may upgrade and renew the marquee pictures.
6.2 setting of cameras 6.2.1 Click on setting button to enter into the interface of setup. click on ，you may turn on the different channels and set up the IP address/corresponding network port/user name and password(if the setup and network are no problem, camera will display on the corresponding channel)click on to apply. As the following figure： 6.2.1.1 If the user needs to revise the parameters of network camera (resolution, FPS,IP parameters and camera name.
6.2.1.2 Select “Network”, you may revise the IP address of network cameras.
6.2.1.3 Select “time/date” to revise the time date. As the following figure: 6.2.1.4 Select PTZ setting (only support IP speed dome). You can slect protocol as Pelco P and Pelco D. IP address is up to 4, baud rate can choose 1200,2400, 4800, 9600, 19200 and speed can support up to 23.
6.2.1.5 Select audio setting. You can choose turn on or off, mode can choose micro phone, horn or both. There are G.771 and PCM sound encoding. Sample sounds is 8K by default. You can select a higher level as 16K. Volume size defaults to 50, the output volume for 75, and noise level is 50 As the following figure： 6.2.1.
6.2.1.7 Select color to adjust brightness, color, contrast and saturation. Allow users to adjust the default value for reset.
6.2.2 In the settings menu, select “video program” to revise the video status of NVR as full time video, motion detection or non-video. Click on one single channel of click on to setup to set up for all channels. As the following figure: 6.2.3 Select “motion detection” in the camera settings. You may set up motion detection, sensitiveness, start video and sending e-mail, etc.
6.2.4 In the camera settings, select automatic cruise (only support high speed dome). The default point can support up to 32 and stay for the high energy set 15 seconds. 32 default points default in a closed state.
6.3 User Setup: Click on to enter the setting interface. select , you may increase users, edit users and delete users. Only the user with administrator permission can carry out the revision. As the following figure: Click on “Add User” will pop-up the following dialogue box. In the white dialog box, you can increase new“Username” , “Password ” and “Description”. The right side will come out the permission option of browsing, playback, management and remote access for new user.
you can increase new“Username” , “Password ” and “Description”. The right side will come out the permission option of browsing, playback, management and remote access for new user. Click on to save. After setting, click on to exit. 6.4 Network Setup Click on to enter setting interface. Select ，if you need to connect by client in the local area network, please set up IP address, subnet mask and gateway. If you need to link internet, please set up domain name server.
6.4.2 Port Setup: Software default page communication ports: 80, video communication ports: 5500 (CMS remote ports use shall correspond), hand controlled communication port: 5577 (no function). As the following figure： 6.4.3 ADSL Setup: Enter the user account, the user's password, select the link, confirm, display status.
6.4.4 DDNS Setup: Select a DDNS service provider, software defaults to www.3322.org, input domain name, user-ID, login password, select the link, and press to confirm. As shown in figure: 6.4.5 E-mail Setup: Set up the time length of mail sent, input the mail address and then confirm.
6.5 Playback Click on playback button ，playback interface will show up（playback channels are up to 4），as the following figure： Click on the channel with record as the following figure： Click on the channels to check, display area to show the video you select.
to playback. Click on the camera twice or hold down the mouse left button to draw into the split box. Then you can playback the video file. The following figure shows video from 7:00~8:00 in the first split box. Select this split bar and it will turn into deep green. Select the time period, the rim will become blue (unit: hour). In the meantime, minute time bar will show the actual video length (unit: minute). The following figure shows manual recording from 19~41 minute.
6.5.2.1 Insert USB to back up.
6.6 Screenshot Click screen shot icon or click screenshot button of the playback interface to catch the current BMP picture from the monitoring or playback split box. As the following figure: In the blank dialog box of picture folder will display the time, lens information of BMP pictures through screenshot. User can choose the time and channel to click search previous pictures. After selecting specific picture, click to backup the current picture.
6.7 Exit from system Click system-exit system to pop up dialog box.
VII. 【Windows CMS remote monitoring software】 7.1Log on to remote monitoring software Please click on the mouse left button twice to install system to Microsoft on your computer (currently supports XP, 32-bit Vista, 32 bit WIN7). Then on your desktop after the installation or Assembly to see NetMonitorClient.
7.2 Add NVR Click the "Add current device" and back to "real-time" viewing. Then you have set the number of channels into the list, To see the picture, please click twice on the number of cameras so that the camera icon will turn into green. Then you can now display the picture.
Click the right button of mouse to show your favorite settings by the function of listing.
For More Information Please check VACRON Website http://www.vacron.
