Wet/Dry Vacuums Aspiradoras Mojado/Seco OPERATOR’S MANUAL MANUAL DEL USUARIO EN P2 ESP P 13 2.5 Gal / 10 L Model No. • Modelo VOM205P 0901 FOR YOUR SAFETY Read and understand this manual before use. Keep this manual for future reference. PARA SU SEGURIDAD Lea y entienda este manual antes de usar. Guarde este manual para futura referencia. Distributed By / Distribuido Por Cleva North America Inc.
TABLE OF CONTENTS Part No. VO70BZ.20.60.02 SECTION Page Warranty…………………………………………………………………………………………...……. Safety Instructions and Warnings……………………………………………………………………. Double Insulation Instructions………………………………………………………………………... Extension Cord…………………………………………………………………………………………. Unpacking and Checking Carton Contents………….……………………..…………….…………. General Assembly Instructions…………………………………………………………….…………. Dry Vacuuming Operation……..
SAFETY INSTRUCTIONS & WARNINGS IMPORTANT SAFETY INSTRUCTIONS Read and understand all instructions before using this vacuum Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before operating. Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your Wet/Dry Vac, use only Armor All® recommended accessories.
DOUBLE INSULATION INSTRUCTIONS This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before servicing. Use this Wet/Dry Vac as described in this manual. Observe the following warnings that appear on the motor housing of your Wet/Dry Vac. DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS.
UNPACKING AND CHECKING CARTON CONTENTS Remove entire contents of carton. Check each item against the carton contents list. Key Description………………... A B C D E F G H I J K L QTY Vac Assembly…………....... 1 Wall Mounting Support……. 1 Hose ……………..........…… 1 Crevice Tool….…………….. 1 2-in-1 Utility Nozzle..………. 1 Small Car Nozzle……………1 Cloth Filter………………….. 1 Foam Filter…………………..1 Screws………… ……………2 Storage Pouch………………1 Detail Kit (6 pc)...…………. .1 Operator’s Manual………….
GENERAL ASSEMBLY INSTRUCTIONS Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and diagram. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts. Estimated Assembly Time: 15 minutes Tools Required for Assembly: Drill, Screwdriver WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC.
IMPORTANT! 11. Do not mount the rack over 5 feet from the floor. Do not screw the rack to drywall only. Secure the screws to a stud. Do not hang from or sit on the vacuum when on mounting rack. Do not use the vacuum while it is mounted on the wall mounting support. Empty the tank before mounting the vacuum on the wall. Make sure the rack is level and mark the hole locations. Make1/8-inch diameter pilot hole in each marked location.
LIQUID VACUUM OPERATION DO NOT USE THE REUSABLE CLOTH FILTER FOR LIQUID VACUUMING. LIQUID VACUUMING WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR AEROSOL SPRAYS.
BLOWING OPERATION This Wet/Dry Vac has blowing capabilities. To use the blower feature follow the instructions listed. WARNING: ALWAYS WEAR SAFETY GOGGLES COMPLYING WITH ANSI Z87.1 (OR IN CANADA, CSAZ94.3) BEFORE USING BLOWER. WARNING: KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS. WARNING: WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE INHALED. 1. 2. 3. 4. 5. 6. Verify that the power cord is disconnected from the outlet. (fig. 1) Make sure the container is empty before using as a blower.
INSTALLING & CLEANING REUSABLE CLOTH FILTER Installing Reusable Cloth Filter 1. Verify that the power cord is disconnected from the outlet. (fig.1) 2. Remove power head and place in upside down position. 3. Slide reusable cloth filter down over the filter cage making sure the whole cage is covered. (fig. 2 & 3) 4. Replace and lock the power head on to the container. Removing and Cleaning Reusable Cloth Filter 1. With the removed power head in the upside down position. 2.
TROUBLESHOOTING WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-UNPLUG BEFORE TROUBLESHOOTING. Symptom Possible Causes Corrective Action Vacuum will not operate. 1) No power supply. 1) Check power supply – cord, breakers, fuses. 2) Unplug and check the power cord. If damaged, have it repaired by a professional. 3) Empty container. 1) Attach or replace the reusable cloth filter. 1) Check nozzle, hose and inlets for blockage. Take off the filter and clean it. Or install new filter. 2) Faulty power cord.
EXPLODED VIEW AND PARTS LIST 12
