Wet/Dry Vacuum Operator’s Manual 6 Gallon Model No. VJF608PF 0201 FOR YOUR SAFETY Read and understand this manual before use. Keep this manual for future reference. Distributed By Cleva North America, Inc. 601 Regent Park Court Greenville, SC 29607 Replacement Filters & Accessories available at: Vacmaster.
TABLE OF CONTENTS SECTION PAGE Warranty......................................................................................................................................... Important Safety Instructions.......................................................................................................... Double Insulation Instructions........................................................................................................ Extension Cords...............................................
IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS VACUUM. Read and understand this operator’s manual and all labels on the vacuum cleaner before operating. Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this vacuum only as described in this manual. To reduce the risk of personal injury or damage to your vacuum, use only manufacturer recommended accessories. SAVE THIS MANUAL FOR FUTURE REFERENCE.
CAUTION: To reduce the risk of injury from moving parts - Unplug before servicing. WARNING: To reduce the risk of electric shock - Unplug before cleaning or servicing. When using as blower: • Direct air discharge only at work area. • Do not use Wet/Dry Vacuum as a sprayer. • Do not direct air at bystanders. • Keep children away when blowing. • Wear safety goggles.
EXTENSION CORDS When using an extension cord with your Wet/Dry Vacuum refer to the following table to determine the required A.W.G. wire size. Before using the cleaner make sure the power cord and extension cord are in good working condition. Make repairs or replacements before using the vacuum cleaner. Only use extension cords that are rated for outdoor use. Length of Extension Cord 120V 25ft (7.62m) 50ft (15.24m) Ampere rating 100ft (30.48m) 150ft (45.72m) A.W.G.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
UNPACKING & CHECKING CARTON CONTENTS A B Remove all contents from the box. Remove the power head and take out any contents inside the collection tank. Check each item against the carton contents list. Carton Contents List: C D E I F G H J K L Power Cord Storage Key A B C D E F G H I J K L Description ..…………....……….….... Qty. Vacuum Assembly…………………….... 1 Hose……………………………………... 1 Extension Wands………………..…...... 2 Utility Nozzle.........................................
GENERAL ASSEMBLY INSTRUCTIONS A Philips head screwdriver is required. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 15 WARNING: DO NOT PLUG THE POWER CORD INTO A POWER OUTLET. MAKE SURE THE PLUG IS DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VACUUM. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE TO RAIN. UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY 1. Verify that the power cord is disconnected from the outlet (Fig. 1). 2. Undo the latches (Fig. 2). 3.
7. Your vacuum comes ready for dry vacuum cleaning. If the cartridge filter is not installed, refer to page 14 for installation instructions (Fig. 10 & 11). 8. For wet vacuum cleaning, remove the cartridge filter, and install the supplied foam wet filter. See page 15 for the foam wet filter installation instructions (Fig. 12). 9. Place the power head back on the collection tank and secure into place using the latches (Fig. 13 & 14). 10.
WARNING: DO NOT PLUG THE POWER CORD INTO A POWER OUTLET. MAKE SURE THE PLUG IS DISCONNECTED BEFORE CHANGING THE FILTERS. CAUTION: DO NOT VACUUM DRYWALL DUST, FIREPLACE SOOT, OR ASH WITH STANDARD WET/DRY FILTER. THIS IS A VERY FINE DUST WHICH WILL NOT BE CAPTURED BY THE FILTER AND MAY CAUSE DAMAGE TO MOTOR. WHEN VACUUMING FINE DUST USE A FINE DUST FILTER (INCLUDED). TO PURCHASE ADDITIONAL FINE DUST FILTERS, CALL 1-866-384-8432 OR GET THEM AT YOUR LOCAL OR ONLINE VACMASTER® RETAILER. 1.
LIQUID VACUUM OPERATION 1 2 6 7 4 3 5 LIQUID VACUUMING WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION ENTITLED “IMPORTANT SAFETY INSTRUCTIONS”. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED TO: LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASED PAINTS, GASOLINE, ALCOHOL, OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO: COAL, MAGNESIUM, GRAIN, OR GUN POWDER.
IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely in the liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve that stops the suction action when the collection tank reaches its maximum capacity. You will notice an increase in motor speed. When this happens, turn off the machine, disconnect from power supply, and drain the liquid into a suitable receptacle or drain.
6. Verify that the power switch is in the ‘O’ OFF position before plugging the power cord into the outlet. Plug the power cord into the outlet (Fig. 4 & 5). 7. Before turning on the vacuum, firmly hold onto the loose end of the hose. Turn the motor on by flipping the switch to the ‘I’ ON position (Fig. 6). 8. Once you have completed blowing, flip the power switch to the ‘O’ OFF position and unplug the power cord from the outlet (Fig. 7).
INSTALLING & CLEANING CARTRIDGE FILTER 1 2 4 3 5 6 INSTALLING CARTRIDGE FILTER 1. Verify that the power cord is disconnected from the outlet (Fig. 1). 2. Remove the power head and place in an upside down position. 3. Install the cartridge filter over the filter cage making sure the cage is completely covered (Fig. 2 & 3). 4. Place the filter retainer on the top of the cartridge filter over the raised lip and tighten down by turning the retainer clockwise; do not over-tighten (Fig. 4 & 5). 5.
INSTALLING & CLEANING FOAM WET FILTER 1 2 4 3 5 INSTALLING FOAM WET FILTER 1. Verify that the power cord is disconnected from the outlet (Fig. 1). 2. Remove the power head and place in an upside down position. Follow instructions to remove the cartridge filter on page 14. 3. Carefully slide the foam wet filter down over the filter cage making sure the cage is completely covered (Fig. 2 & 3). 4. Place the power head onto the collection tank. CLEANING FOAM WET FILTER 1.
TROUBLESHOOTING WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, UNPLUG BEFORE TROUBLESHOOTING. PROBLEM POSSIBLE CAUSE Check the power supply, cord, breakers, and fuses. No power supply. The wet/dry vacuum will not Faulty power cord. operate. Collection tank is full. Switch in the wrong position. The dust comes out from the motor cover. Reduced efficiency and motor/speed vibration. SOLUTION Unplug and check the power cord. If damaged, have it repaired by a professional. Empty the collection tank.
EXPLODED VIEW 17
PARTS LIST Part Drawing Number Description Quantity 1 551489101 Handle Assembly 1 2 551011103 Hose Storage Rack 2 Power Head Assembly 1 3 4 551416106 Float 1 5 551437105 Filter Cage 1 Collection Tank 1 6 7 551011106 Vacuum Port 1 8 551015104 Caster Foot Assembly 4 9 551541101 Hose 1 10 551001121 Extension Wand 2 11 551011109 Utility Nozzle 1 12 551001117 Floor Brush/Squeegee Nozzle 1 13 551254103 Cartridge Filter 1 14 551002118 Foam Wet Filter 1 15 55
