2 -Wire Intercom System DT596(F)/ID User Manual RF CARD DT596/ID RF CARD DT596F/ID DT-ENG-596(F)ID-V1 110S923
Contents 1.Parts and Functions............................................................................................. 1 2.Terminal Descriptions........................................................................................... 1 3.Door Station Mounting.......................................................................................... 2 4. System Wiring and Electric Lock Connection...................................................... 4 5.DIP Switches Setting.............................
1.Parts and Functions Camera Lens Speaker RF CARD 176 mm Indicator ID card window RF CARD 28 mm Nameplate Call Button Microphone Rainy Cover DT596/ID 90 mm Camera Lens Speaker RF CARD ID card window 220 mm Indicator RF CARD Nameplate Call Button Screws for panel mounting Microphone DT596F/ID Mounting box Side View 119 mm 2.
•• •• •• •• •• JP/LK(Lock Control Jumper): To select the lock type: see section 4 Doorstation Code DIP: Total 4 door stations can be supported,see section 5 RS485:Used to update the program for door station MIC: Adjust the volume of Microphone SPK: Adjust the volume of Speaker •• •• •• •• •• Main Connect Port: To connect the bus line and the electronic locks. BUS: Connect to the bus line, no polarity. PL: External lock power input, connect to the power positive(power +).
DT596F/ID Mounting 1 2 adjust camera angle m 174mm 90m 52m m PS Drill a hole in the wall to match the size of the mounting box and attach to the wall. 3 Attach the panel to the mounting box and use screws supplied to fix the panel Connect the cable correctly and adjust right angle for camera 4 Place name label Adjusting Camera Angle use a screwdriver to loosen the screw,then adjust an appropriate camera angle, after finishing , use the screwdriver to fix the screw.
Placing Name Label Press the plastic cover on right/left side to move away the cover,insert a name paper,then put the plastic cover back to the panel. RF CARD 4.
Electric Lock Connection Door Lock Controlled with Internal Power Note: 1. Electronic lock of Power-on-to-unlock type should be used. 2. The door lock is limited to 12V, and holding current must be less than 250mA. 3. The door lock control is not timed from Exit Button(EB). 4. The Unlock Mode Parameter of Monitor must be set to 0 (by default).
connect one lock connect two locks Take off the Jumper BUS S1 + PL S2 + Take off the Jumper S- BUS POWER SUPPLY PL S1 + S2 + S- POWER SUPPLY LOCK LOCK LOCK Unlock parameter setting(set on monitor) Manual Monitor Memory Playback Monitor Album ? About 1.Touch menu page. Intercom Multimedia Close User Setup 09/30/2010 Thu.16:41 item on main H/W : S/W: Local addr: Unlock timing: Video standard: UI-CODE: MCM-VER.: Updated: --- a1.3 V17.11.418.00 ----------- 2.
Multi Door Stations Connection monitors DPS DBC4 BUS PS5 A B C D 85~260VAC 4# Camera 3# Camera ID=11 L1 L2 PL S1+ S2+ S- 2# Camera ID=01 1# Camera ID=00 ID=10 ON ON ON ON 1 234 1 234 1 234 1 234 L1 L2 PL S1+ S2+ S- L1 L2 PL S1+ S2+ S- L1 L2 PL S1+ S2+ S- -7-
Multi Monitors Connection Basic IN-OUT Wiring Mode ON monitor 1 2 3 4 56 Code=15, DIP-6=on ON monitor 1 2 3 4 5 6 Code=14, DIP-6=off ON monitor 1 2 3 4 5 6 Code=0, DIP-6=off PS5 DPS 85~260AC ID=00 RF CARD ON 1 234 -8-
With DBC-4 Wiring Mode ON ON 1 2 3 4 5 6 monitor monitor 1 2 3 4 5 6 HI OUT IN Code=14, DIP-6=on Code=15, DIP-6=on A B C D DBC-4 ON ON 1 2 3 4 5 6 monitor Code=13, DIP-6=on ON ON 1 2 3 4 5 6 monitor 1 2 3 4 5 6 Code=12, DIP-6=on monitor HI monitor 1 2 3 4 5 6 OUT IN Code=2, DIP-6=on Code=3, DIP-6=on A B C D 1 2 3 4 5 6 Code=1, DIP-6=on DBC-4 ON ON monitor monitor 1 2 3 4 5 6 Code=0, DIP-6=on DPS PS5 85~260AC ID=00 RF CARD ON 1 2 -9-
Extending Connections with DCU unit ON ON CALL UNLOCK CALL UNLOCK TALK/MON TALK/MON IN-USE IN-USE 1 2 3 4 5 6 HI 1 2 3 4 5 6 Code=3, DIP-6=on OUT IN Code=2, DIP-6=on ON CALL UNLOCK CALL UNLOCK TALK/MON TALK/MON IN-USE IN-USE 1 2 3 4 5 6 1 2 3 4 5 6 Code=1, DIP-6=on Code=0, DIP-6=on AC DCU Code =3(11) ON ON 123456 DBC-4 BUS 1234 DPS DCU PS5 A B C D 85~260VAC Camera 1 Camera 2 RF CARD ID=00 RF CARD ID=10 ON ON 1 2 1 2 Doorstation 1 RF CARD ID=01 ON 1 2 Doorsta
5.DIP Switches Setting ON(1) ON = OFF(0) ON = DIP Switches Settings of Door Station Total 4 bits on the DIP switches can be configured.The switches can be modified either before or after installation. Setting Item Bit state ON 1 2 34 Bit1 and Bit2 (it is used to set the ID code for door station) ON 1 2 34 ON 1 2 34 ON 1 2 34 ON Bit3 1 234 ON 1 234 Bit4 Descriptions Default setting, ID = 0(00), set to the first Door Station. ID = 1(10), set to the second Door Station.
Bit-6 is used to match the video impendance, which have to be set to on if the monitor is in the end of the bus, otherwise set to off. Bit state ON 1 2 3 4 5 6 Setting The monitor is not at the end of the bus. Bit state ON 1 2 3 4 5 6 Setting The monitor is at the end of the bus. Bit-1 to Bit-5 are used to User Code setting.The DT596(F)/ID responds to 0~15 .
Add User Cards: 1.Control one lock(the first lock) Show the MASTER CARD ADD card to ID card window in standby mode. red blue (on) (off) beep+,beep Show user cards to be added, one by one. red blue (blink)(off) beep+ Show the MASTER CARD ADD card to exit.But it will return to standby mode if no operation within 15s. red blue (off) (off) beep,beep+ 2.Control two locks Show the MASTER CARD ADD card to ID card window in standby mode. red blue (on) (off) beep+,beep Press "CALL" button.
Authorize master cards: By default,there are two master cards marked MASTER CARD ADD and MASTER CARD DELETE ,but you should know that the master card can be authorized by users at any time.That means any two user cards can be authorized to master cards,When registered new master cards, the old master cards are invalid automatically. Continuously set DIP4 switch status to "off"->"on" ->"off">"on"->off"->"on" in sequence,must finish in 3s.
•• You can activate the electric door strike by pressing the request to exit button connected to the unit. Pressing request to exit button 1 releases relay 1, and pressing request to exit button 2 releases relay 2.(The unlock function will work when the request to exit button is pushed, even while the proximity access is forbidden. 1. If show the authorized user card,the buzzer will sound of beep+,and the LED indicator will light up. 2.
10. Cables Requirements The maximum distance of the wiring is limited in the DT system. Using different cables may also affect the maximum distance which the system can reach. The farest monitor monitor with two or four monitors monitor monitor DBC/DBC-4 B C When Monitor quantity < 20 DPS Cable Usage A B C Twisted cable 2x0.75 mm2 60 60 30 Twisted cable 2x1 mm2 80 80 40 A When Monitor quantity > 20 Cable Usage A B C Twisted cable 2x1 mm2 70 30 20 Twisted cable 2x1.
Note:
The design and specifications can be modified without notice to the user. Right to interpret and copyright of this manual are reserved.
