DT24 USER MANUAL(EN) 2-Wire Video Intercom System Read this manual carefully before using the product, and keep it well for future use.
Introduction The monitor is designed with 4 inch screen, it provides a resolution of 320x240 pixels with high quality image display, and it equipped with a handset to communicate. The touch sensitive button makes the operation more easily.
Unit Mounting 145~160 cm Accessory contents: Accessories include a Bracket, two 4X25 screws (use to fasten the Mounting Bracket), 2 wire connectors (use to connect with Monitor). Installation steps: Installation height for indoor monitor usually is 145~160cm(refer to sketch map). Wire the cable correctly(see the later connection chapter) then hang the Monitor on the Mounting Bracket firmly. About Main Menu The main menu is your starting point for using all the applications on your monitor.
• Pick up handset to talk with the visitor, the talking duration time is 90s. To end the conversation, please hand up the handset. If the system connects two or more Monitors, pick up any Monitor, the others will be automatically shut off. Door Release During talking state, Press UNLOCK button to open the door for the visitor. Entrance Monitoring When the monitor is in standby mode, press MONITOR button(or select Monitor ... item on main menu page), The screen can display the view of outside.
swers the call, conversation is started.and the other monitors will stop ringing at the same time. (Note:the user code of all monitors must be same.) Direct Call Guard unit: A Monitor can be assigned as Guard Unit Monitor; when the Guard Unit Monitor answers the call, conversation with the guard person is started.. Intercom Call Intercom Intercom Call ... Inner Call ... Direct Call Guard Unit ... Exit OK Select Item [ 00 ] [ 01 ] [ 02 ] [ 03 ] [ 04 ] [ 05 ] Jim. Zhang Calo. Liu Jacko. Zhang Philips.
Monitor Time Setting Select Manual Monitor item on main menu page, then select Monitor Time Set... item. Use / button to increase / decrease the value, press MENU button to confirm and return last page. Monitor Time Select Current : Cancel 01min Save&Exit Last/Next Screen Setting During monitoring or talking state, press MENU button,the ADJUST MENU will be displayed. Use / button to select the adjustMemo button to ment item, use change the value. Scene Bright Color Select Camera ...
Step1 Step2 Main Menu H/W : S/W: Local addr: Unlock timing: Unlock2 select: Video standard: Language: Monitor ...
2 locks control: The monitor can be set to control 2 locks while you should set the unlock2 item to “on “ state. The code number of 8015 is used to set the unlock2 off that it can only control one lock. The code number of 8014 is used to set the unlock2 on that it can control two locks. Note:1. During talking or monitoring state, UNLOCK button,two unlock icons will be showed. Use / button to select the 1 item you want, and press UNLOCK or 2 MENU button to release the corresponding door,select item to exit.
Note: 1. the monitor can only support 4 languages. English,French,Spanish and German are default.But you can customize any 4 languages by yourself. 2. we reserve the copyright to add languages without notice to users. How to set the address for monitor Each monitor should be assigned an address in the system, total 32 addresses can be configured, the code number of 8200 to 8231 is used to controlled the address of 00 to 31. Please refer to the following table. -10- Input No. User Code Input No.
Specification: • • • • • • • Power Supply: Power Consumption: Monitor Screen: Display Resolutions: Video Signal: Wiring: Dimension: DC 24V Standby 6mA; Working status 194mA 4 Inch color LCD 320(R, G, B) x 240 pixels 1Vp-p, 75Ω, CCIR standard 2 wires, non-polarity 186(H)×190(W)×26(D)mm Precautions 1) All components should be protected from violence vibration. And not allow to be impacted, knocked and dropped.
The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.
