DMR18 Door Station User Manual RF CARD 1 2 3 4 5 6 7 8 9 * 0 # Please read this manual carefully before using the product you purchase, and keep it well for future use.We reserve the right to modify the specification in this manual at any time without notice.
1.Parts and Functions Camera Lens Night View LED Adjustable Camera 350 mm Speaker LCD Screen ID Card Window Connectiong Port RF CARD 3 2 1 Digital Keypad 1 2 3 4 5 6 7 8 9 * 0 # Microphone 128 mm With rainy cover 2. Terminal Descriptions SD Card Slot L1 L2 +12V EB+ EBN.O LK+ LK- CN-LK T/R -T/R+ Bus 3 2 1 RF CARD 3 2 1 1 4 • • • • • • • • • • -1- 2 3 5 6 7 8 9 * 0 # J/KMB JP-LK +12V: 12VDC power output. LK-(GND): power ground.
.Door Station Mounting 1 2 3 Camera angle The view for rainy cover after mounted Drill a hole and attach the rainy cover to it 4 5 Attach screws to fix the metal box Adjust the camera angle and attach the metal to the panel and wire correctly.
. Door Lock Connections 1. Internal Power Supply Mode Use the power of the system to supply for the electronic lock, so that the lock can be connected to the door station directly, without an additional power supply for the electronic lock. Note that the door station can only output 12Vdc power, therefore the kind of lock is limited.
2. External Power Supply Mode When the electronic lock is over 12 Vdc, additional power supply for the lock is needed. • The power supply for the lock must be less than 48Vdc 1.5A. • The Jumper must be removed when using external power supply. The default setting is Power-to-Unlock type(Normally open mode), if use Power-off-to-Unlock type, change the Unlock Relay mode to Normally closed mode .Note that the unlock relay mode is set on the Parameter tab of DT CONFIG software.
5. Door Station Configurations 1. About room code(address): Room Code(also called room address) is a code assigned to each monitor, to identify different monitors; each monitor have a unique room code in one buidling.The room Code is stored in each Monitor’s inner EEPROM memory, and does not lose even the monitor is power off. 2. About Debug State: The Debug State is your starting point for using all the applications on DMR18.
Table 1: Item Submenu 1. Installer Setup 1. ID Code [1] 2. Unlock Timing [05] 3. Unlock Output [0] 4. Card Memory [0] 5. Doorplate Mode 6. Audio Options ... 7. Parameters ... 8. Installer Code ... 9. Default ... 2. Setup 1. Language [1] 2. Tone Select [03] 3. Tone Volume [08] 4. Unlock Code [1111] 5. Display Mode 6. Clock ... 7. Setup Code ... 8. About .
Basic Tools Detail: Table 2(Installer Setup): Item ID Code Unlock Timing Unlock Output -7 - Factory set Description If only one door station is installed in this building, set to 1; [1] If multi door stations are installed, primary door station Single must be set to 1, and other slave door stations must be set from 2 to 4. Note that max. 4 door stations is available in one building To set the time that how long the door keeps open [05] when door is released. Range from 01 to 99 seconds.
Table 2.1(Parameters): Item Description Factory set Monitor Timing To show the monitor time,Range from 6s to 600s Switch Timing To show the surveillance time for each Door Station or 40s CCTV camera.Range from 6s to 600s Wait Timing To show the calling wait time,Range from 10s to 600s 30s Talk Timing To show the limitation time of talking,Range from 10s to 600s Monitor & Speak To enable Indoor Monitor under monitoring state can speak to Door Station at same time.
Table 3(Setup): Item Language Tone Select Tone Volume Unlock Code Display Mode Clock ... Setup Code -9- Description To change language.the code format is 4 digits.Please refer to part 5,section 10(change door station language) for more detail informations. Select the chime of Door Station in calling wait state, 12 chord tunes are available, key in 01 to 12 to select. Adjust the tone volume for dooor station in calling.
Table 4(Card Memory): Item Description Add Card ... To add the user card Delete By Card To delete card by user card Delete By M.code To delete card by room code Cards Information To show the informations about cards Format To format informations about cards Factory set 4. Calling and Unlock Operation: The DMR18 door station is a digital station with 320*240 pixels LCD screen, color CCD camera, night view LED, and digital keypad.
1. ID Code.[1] >> Debug State << 2. Unlock Timing[05] 0-# Redial Tools 1. Installer Setup 2. Setup 1-# 2-# To o l s Exits 3. Card Memory Pres NO. 4 . O n l i n e M o n i t o r s to select 5 . O n l i n e D e v i c e s *Back In Debug State, press '1#' key 6 . Vo l t a g e M e a s u r e In Tools menu, press '1' key 3. Unlock Output[0] Installer 4. Card Memory [0] Setup 5. Doorplate Mode Press No. to select *Back 6. Audio Options ... 7. Parameters ... 8. Installer Code... 9.
7. Change Installer Code(administrator password): The Installer Code is the password to access the door station debug State. The default Installer Code is '66666666'. Note that if the Default Set have been activated, the Installer Code will be set to default value. 1. ID Code >> Debug State << [1] 2. Unlock Timing[05] 0-# Redial 1. Installer Setup Tools 2. Setup 1-# 2-# 3. Card Memory To o l s Exits Pres NO. 4 . O n l i n e M o n i t o r s to select 5 . O n l i n e D e v i c e s 6 .
9. Change Unlcok Code: If door station runs as Debug State, you can press “1#” to activate Tools Menu, then select “2” to enter setup page,then select 4 item.If it runs as Normal State, follow these steps: [ 8002 ] Setup 2 3 4 5 6 7 8 9 * 0 # Please Input Password Press “#”,Input “8002”, then input Setup Code or Admin Code(88888888 or 66666666 by default) 4. Unlock Code[1111] [----] 4. Unlock Code[1111] 5. Display Mode RF CARD 1 1. Language [1] 2 . To n e S e l e c t [ 0 3 ] 3 .
1. AddCard ... 1. AddCard ... [--] [01] Please Input Room Code # Save [01] C a r d numbs : 1 5 9 7 7 1 3 1 Show the card * Back Show The Card # Save * Back # Save Us C a er rd * Back 1. AddCard ... Enter Add Card menu, and Room Code is asked. Input Room Code Read the card to be authorized Delete user cards: Registered User Cards/Key Fobs can be deleted from the Door station,once doing the delete operation,the card/key fobs can not open the door anymore.
Card information: 4. Cards Information Enter Card Information page, and the screen will display the authorized User Cards count, and card read access events count. Card Count: 1000 * Back # Save Format: 5. Format Enter Card Format page, a password will be asked,input 8 digits installer password (66666666 by default),then press" #" key to save,format operation is activated.all card information will be cleared. [--------] Please Input Password * Back # Save 11.
Setup [ 8002 ] 2 3 4 5 6 7 8 9 * 0 # 1. Language [----] 4. Unlock Code[1111] 5. Display Mode RF CARD 1 1. Language [1] 2 . To n e S e l e c t [ 0 3 ] 3 . To n e V o l u m e [ 0 3 ] Press No. to select *Back Please Input Password Press “#”,Input “8002”, then input Setup Code or Admin Code 6. Clock 7. Setup Code 8. About 9. Default ( Code Number) *Back Input 4 digits code number, Refer to the table.
Check online monitors: >> Debug State << 4. Online Monitors 0-# Redial 1-# To o l s Tools 1. Installer Setup [--]~[--] 2. Setup 2-# 3. Card Memory Pres NO. 4 . O n l i n e M o n i t o r s to select 5 . O n l i n e D e v i c e s Exits *Back In Debug State, press '1 #' key 6 . Vo l t a g e M e a s u r e Press '4' key (Search Range) * Back # Save Input 2 digits monitor code 4#.Online Monitors Search Range: input the monitor adress. For example, input the range from 01 to 05.
6. Specification ●● Power supply: DC24V(Powered by DT-DPS) ●● Camera Lens: 1/4 ACS 4T image sensor with DSP processor ●● Power consumption: Standby 3W;Working status 9W ●● Screen: 3.
DT-ENG-DMR18-V1 2011S0621
