Owner's manual

Page 88
K5 System Technical Guide
4.6.3§Access§control-GP-ACS
GP-ACS is access controller. It can work as a standalone access controller or work with C5-IPC to be
connected to the network.
1
2
3
4
C5-AT27
PS5
1 2 3
6
5
4
7
8
9
#
0
*
RF CARD
CN1 CN2
CN-LK
J/KMB
JP-LK
Bus
EB+ EB- N.O LK+ LK-
+12V
1
2
3
T/R- T/R+
1
2
3
P+ P- P+ P-
RS485
SW1
JWB(IN) JWB(OUT) CN(MDS) ETHERNET
PA
VR600
+
S1
POWER
LINK
IN-USE
AG
1
ON
ON
DIP
DIP
2 3
4
5
6
1
2
3
P+
P+ P-
RS485
RS485
SW1
CN(MDS) ETHERNET
C5-IPC
C5-F414
IP-MR18
AC
+
-
+
-
+
-
+
-
+
-
To other monitors
PS5
AC
+
-
1R
2W
GD VD
T/R+
T/R-
Z1
Z2 Z3 Z4 COM COM
PR
3Y
4B FV+
FV-
P-
AU P- P+
P+D1&D2
To Next C5-F414
F4/F4DV/F4Q
ON
DIP
Keep 3 jumpers
LAN
CAT5
RVV2*1.0mm
２
Note that ID Code(#8001-1) setting in MR18 must be set to 1
PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT)
VD-SET(L=HIGH)
P-
P+
P-
P+
PA
S1
1
ON
2
T/R- ERROR INUSE LINK POWER T/R+
PORT-A PORT-B PORT-C PORT-D
JWB(OUT)
JWB(IN)
JWB(OUT)
P-
P+
P+
P-
P-
A1
D1
D2
P-
+
-
P-
P+
P+
P-
VD-SET
HI / VD
1
2
3
4
C5-AT27
C5-F414
To other monitors
1R
2W
GD VD
T/R+
T/R-
Z1
Z2 Z3 Z4 COM COM
PR
3Y
4B FV+
FV-
P-
AU P- P+
P+D1&D2
PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT)
VD-SET(L=HIGH)
P-
P+
P-
P+
PA
S1
1
ON
2
T/R- ERROR INUSE LINK POWER T/R+
PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT)
+
-
P-
P+
P+
P-
VD-SET
HI / VD
+
-
+
-
To Next PS5
A single cable to connect
P-(Ground) together
Note that VD-SET must be set to VD if the C5-F414 is the last one of the bus
HI / VD
GP-ACS
1
ON DIP
2 3 4 5 6
P+ A1 P- D1 D2 JWB(IN) JWB(OUT)
P-
JP-LK1
JP-LK2
S1
SN- SN+
P+
P-
POWER LINK IN-USE
PA
RS485
1
2
3
1
2
3
EB+ EB- N.O LK+ LK-
+12V
BEEP LED
LED2
LED1
WG1 WG0 P-
+12V
JWB(IN)
JWB(OUT)
JWB(IN)
Chapter 4 K5 System Settings