Owner's manual

Page 83
K5 System Technical Guide
4.5.3§Connecon§Schemac
With two C5-MDS in the system
JWB(IN4)
P-
P+
P-
P+
PA
S1
1
ON DIP
2 3 4 5 6
JWB(IN3) JWB(IN2) JWB(IN1) JWB(OUT)
T/R-
ERROR
INUSE
LINK
POWER
T/R+
P-
P+
P+
P-
JWB(IN4)
P-
P+
P-
P+
PA
S1
1
ON DIP
2 3 4 5 6
JWB(IN3)
JWB(IN2)
JWB(IN1) JWB(OUT)
T/R-
ERROR
INUSE
LINK
POWER
T/R+
P-
P+
P+
P-
1 2 3
6
5
4
7
8
9
#
0
*
RF CARD
CN1 CN2
CN-LK
J/KMB
JP-LK
Bus
EB+ EB- N.O LK+ LK-
+12V
1
2
3
T/R- T/R+
1
2
3
P+ P- P+ P-
RS485
SW1
JWB(IN)
JWB(OUT)
CN(MDS)
ETHERNET
PA
VR600
+
S1
POWER
LINK
IN-USE
AG
1
ON
ON
DIP
DIP
2 3
4
5
6
1
2
3
P+
P+ P-
RS485
SW1
JWB(OUT) ETHERNET
C5-IPC
C5-MDS
C5-MDS
IP-MR18
+
-
+
-
PS5
AC
+
-
F4/F4DV/F4Q
ON
DIP
Remove 3 jumpers
LAN
Note that ID Code(#8001-1) setting in MR18 must be set to 8
1 2 3
6
5
4
7
8
9
#
0
*
RF CARD
CN1 CN2
CN-LK
J/KMB
JP-LK
Bus
EB+
EB-
N.O
LK+
LK-
+12V
1
2
3
T/R- T/R+
IP-MR18
+
-
Note that ID Code(#8001-1) setting in MR18 must be set to 1
JWB(IN)
+
+
-
-
ON
DIP
JWB(OUT)
P-
1V 4A/2V 2A/1V 1A
1V 4A/2V 2A/1V 1A
CN(MDS)
1
2
3
4
C5-AT27
C5-F414
To other monitors
To other door
To other door
PS5
AC
+
-
1R
2W
GD VD
T/R+
T/R-
Z1
Z2 Z3 Z4 COM COM
PR
3Y
4B FV+
FV-
P-
AU P- P+
P+D1&D2
To Next C5-F414
PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT)
VD-SET(L=HIGH)
P-
P+
P-
P+
PA
S1
1
ON
2
T/R- ERROR INUSE LINK POWER T/R+
PORT-A PORT-B PORT-C PORT-D JWB(IN)
JWB(OUT)
+
-
P-
P+
P+
P-
VD-SET
HI / VD
1
2
3
4
C5-AT27
C5-F414
To other monitors
1R
2W
GD VD
T/R+
T/R-
Z1
Z2 Z3 Z4 COM COM
PR
3Y
4B FV+
FV-
P-
AU P- P+
P+D1&D2
PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT)
VD-SET(L=HIGH)
P-
P+
P-
P+
PA
S1
1
ON
2
T/R- ERROR INUSE LINK POWER T/R+
PORT-A PORT-B PORT-C PORT-D JWB(OUT)
+
-
P-
P+
P+
P-
VD-SET
HI / VD
+
-
To Next PS5
Note that VD-SET must be set to VD if the C5-F414 is the last one of the bus
HI / VD
JWB(IN)
CAT5
RVV2*1.0mm
２
A single cable to connect
P-(Ground) together
JWB(IN4)
JWB(IN1)
JWB(IN3)
JWB(IN2)
123
4
567
8
JWB(OUT)
JWB(IN4)
JWB(IN1)
JWB(IN3)
JWB(IN2)