Owner's manual

ManualsBrandsV-Tech ManualsAccessories communicationCAT5 System Technical Guide

K5 SYSTEM

Technical guide 2012

Summary of content (156 pages)

PAGE 1
K5 SYSTEM Technical guide 2012
PAGE 2
SYSTEM FEAGUTES Large capacity Simple installation Signal isolution Debug online PRODUCT FEAGUTES Menu Guide Page 2 Intercom Picture Memory K5 System Technical Guide Multi Channels
PAGE 3
Chapter 1: K5 System Overview .................................. 10 1.1 System Description..................................................11 1.2 System Features......................................................12 1.3 System Applications.................................................13 Chapter 2: K5 System Parts.......................................... 14 2.1 Wiring Diagram.......................................................15 2.2 Product List......................................................
PAGE 4
Contents 2.3.3.3 Specification..........................................25 2.3.4 Accessories......................................................25 2.3.4.1 C5-F4...................................................25 2.3.4.2 C5-F414................................................26 2.3.4.3 C5-F422................................................27 2.3.4.4 IP Converter: C5-IPC..............................28 2.3.4.5 Multi-Door station Switcher: C5-MDS........29 2.3.4.6 Picture Memory Controller: C5-IMC.......
PAGE 5
3.4.1 Layout............................................................39 3.4.2 List of Accessories............................................39 Chapter 4: K5 SYSTEM SETTINGS................................. 40 4.1 Door station Setting.................................................41 4.1.1 Door station working mode................................41 4.1.2 IP-MR9L Configuration......................................41 4.1.2.1 How to enter debug mode......................41 4.1.2.2 Program Menu overview....
PAGE 6
Contents 4.3.3 Address Setting with door station.......................68 4.4 C5-IPC Setting........................................................70 4.4.1 Port Description................................................70 4.4.2 Settings..........................................................70 4.4.2.1 Level Switch setting................................70 4.4.2.2 DIP switch setting...................................71 4.4.2.3 IP Address Setting..................................72 4.4.2.
PAGE 7
4.6.2.1 Connection Schematic.............................87 4.6.3 Access control-GP-ACS......................................88 4.6.4 Camera control-CM-IPC.....................................89 Chapter 5: K5 SYSTEM SOFTWARES.............................. 90 5.1 PC Station Installation..............................................92 5.2 IP Address Setup.....................................................96 5.2.1 General Rules for IP Address Setup.....................96 5.2.
PAGE 8
Contents 5.3.6.2 Event up Setting ................................. 115 5.3.6.3 Input table.......................................... 115 5.3.6.4 IP Table............................................... 116 5.3.7 Management of Block C5-IPC........................... 117 5.3.7.1 Call Table............................................ 117 5.3.7.2 Parameters Management....................... 119 5.3.8 Management of Common C5-IPC...................... 123 5.3.8.1 Call Table.......................................
PAGE 9
5.4.5.3 Record List.......................................... 136 5.4.6 Capture Viewer.............................................. 138 5.4.7 Setting.......................................................... 139 5.4.7.1 General............................................... 139 5.4.7.2 Alarm Setting....................................... 140 5.4.7.3 View & Layout...................................... 142 5.4.7.4 Handset.............................................. 143 5.4.7.5 Security & Startup...........
PAGE 10
Chapter 1 K5 System Overview Chapter 1 K5 System Overview 1.1 System Description................................................................. 11 1.2 System Features..................................................................... 12 1.3 System Applications................................................................
PAGE 11
§§1.1 System Description The K5 system is the ideal system for simplifying installation in residential compounds with a high number of users, developed with innovative technology, allows the installation of video intercom systems up to 239 blocks and 512 users per block, applying CAT5 cable only except the power supply to the system. This system consists of six main components: outdoor station, indoor monitor, IP converter, distributor, power supply and other accessories.
PAGE 12
Chapter 1 K5 System Overview §§1.2 System Features •• Max. 512 apartments per block •• Max.8 door stations per block •• Max 3 monitors in one flat •• Max. 239 blocks in network Network Door/camera Monitor 239 8 512 Per Block •• Max.
PAGE 13
§§1.3 System Applications Large residential compound One of the advanced features of K5 intercom system is that it supports 239 blocks in one system; it can satisfy almost any size of residential compounds. Using a standard CAT5 network, each block is able to accommodate hundreds of monitors and multiple outdoor stations. Each building may have up to 8 outdoor stations. Max.14 Switchboards make management of community more convenient.
PAGE 14
Chapter 2 K5 System Parts Chapter 2 K5 System Parts 2.1 Wiring Diagram....................................................................... 15 2.2 Product List............................................................................ 16 2.3 System Parts.......................................................................... 17 2.3.1 Outdoor Station: IP-MR18................................................ 17 2.3.2 Indoor Monitor: C5-AT27................................................. 20 2.3.
PAGE 15
§§2.1 Wiring Diagram The below diagram demonstrates what the K5 system can do, by all the connecting different devices up.
PAGE 16
Chapter 2 K5 System Parts §§2.
PAGE 17
§§2.3 System Parts 2.3.1 Outdoor Station: IP-MR18 Full aluminum panel with luxurious and elegant appearance, design with 3.5” TFT color display for versatile, innovative and high-performing communication. 2.3.1.1 Features Functions such as monitoring, call, conversation and door lock release, etc •• Full anodize aluminum panel; •• CCD camera angle is adjustable; •• 3.
PAGE 18
Chapter 2 K5 System Parts 1. Camera Lens: Capture images 2. Night View LED: Compensate light 3. Speaker: Conversation between visitors and users 4. LCD Screen: Show operational tips and others 5. Card Window: Access control with ID/IC card 6. Digital Keypad: Making call and parameters setting 7. Microphone: Conversation between visitors and users 8. Adjustable Camera: Adjust the camera angle 9. Connecting port: Connect door station with other devices 2.3.1.
PAGE 19
2.3.1.4 Door Station Functions Digital call by visitors A visitor can input the resident’s room number to be shown on the display, As the signal transfer to monitor, the resident can answer to communicate with visitor and release the lock. When necessary, the visitor or resident can dial 0000 to call Switchboard for help. While waiting or during the conversation, the visitor can end conversation by pressing the * key, to end the call.
PAGE 20
Chapter 2 K5 System Parts 2.3.2 Indoor Monitor: C5-AT27 With 7” digital TFT touch screen and touch sensor button, this monitor is the best choice for modern intelligent life. Three different elegant appearances can satisfy different requirements. 2.3.2.1 Features •• 7 inch wide screen digital TFT LCD; •• Full touch screen and touch sensor button; •• Automatically record picture and max.
PAGE 21
1. LCD screen: Display the images from outdoor station. Touch operation 2. LED indicator: Normally light on when in use 3. Unlock key: Press to release the door for visitors during talking or monitoring 4. Mon/Talk key: Press to view the outside condition or to talk with the visitors while receiving a call 5. Menu key: Press to open a list of operations available on the current screen 6. Microphone: Send voice when talking 7. Speaker: receives voice when talking 8.
PAGE 22
Chapter 2 K5 System Parts 2.3.2.4 Indoor Monitor Functions Receiving calls Call from door station: When the monitor rings, it means a call is coming. The display will show the video from the door station camera, press the answer button to accept the call and press the answer button again to end the call after finish the conversation Call from Switchboard: When handset rings, the display can show the video from the Switchboard camera(if the Switchboard is fitted with one camera).
PAGE 23
2.3.3 Switchboard: IP-G21 IP-G21 is the advanced Switchboard for K5 system, designed as a dedicated switchboard to support K5 network system. Switchboard is an essential part in K5 system, it makes possible to manage calls from (to) Common Door Station or Door Station, and Indoor Monitor. Additionally, IP-G21 has other functions, such as alarm receiver, depends on system configuration. Max. 8 IP-G21 can be connected in system.
PAGE 24
Chapter 2 K5 System Parts 1. LCD screen: Display the icon menu and images ,touch operation 2. Microphone: Receives sound from the user 3. Alarm Button: Blink when the guard unit receives alarm record 4. LED Indicator: (1) Red indicator flash first, green indicator flash later when power on; (2) Blue indicator normally on when work in normal; (3) Blue indicator flash when in calling state; (4) Red indicator flash when in talking state 5.
PAGE 25
2.3.3.3 Specification Power input: DC 24V Standby Current: 390mA Working Current: 850mA Screen: 10 inch digital TFT Resolution: 800x480pixels Video Signal: CCIR, 1Vp-p, 75Ω Transmission Mode: TCP/IP Connection Port: RJ45 Network Interface: Standard Ethernet interface Working temperature: -100C ~ +400C Dimension: 382 *203 *32mm 2.3.
PAGE 26
Chapter 2 K5 System Parts •• LINK: Signal indicator. Flicker means signal is transmitted in bus •• Power: Power indicator. Always ON •• IN-USE: Status Indicator. ON while working Specifications Power supply: DC24V Standby current: 8mA Working current: 80mA Working temperature: -100C~400C Connection port: RJ45 Dimensions: 88*140*32mm 2.3.4.2 C5-F414 C5-F414 can support four audio and one video channels at the same time while working.
PAGE 27
connected to next distributor •• PORT-A, PORT-B, PORT-C, PORT-D: 4 output, it can be connected to indoor monitors •• VD-SET: Setting for video matching Specifications Power supply: DC24V Standby current: 60mA Working current: 120mA Working temperature: -100C~400C Connection port: RJ45 Dimensions: 140*150*60mm 2.3.4.3 C5-F422 C5-F422 is a advanced distributor which can support two audio and video channels at the same time.
PAGE 28
Chapter 2 K5 System Parts Specifications Power supply: DC24V Standby current: 60mA Working current: 120mA Working temperature: -100C~400C Connection port: RJ45 Dimensions: 140*150*60mm 2.3.4.4 IP Converter: C5-IPC C5-IPC is a network controller. It serves as system controller, manages all the data in the system communication. To severs as a IP converter to effect the network connection.
PAGE 29
station only •• JWB (OUT): Bus Signal Output. RJ45 port includes audio, data & video. It can be connected to distributor. •• CN-MDS: Bus Signal Input. RJ45 port, connected to MDS only •• CN-NET: RJ45 Network Port, connected to LAN •• JP1/JP2/JP3: Jumper. Removed if C5-MDS connected •• SWI: Distributor Setting.
PAGE 30
K5 System Parts S1 ON 1 DIP 2 3 4 5 ERROR LINK RS-485 6 IN-USE •• PA: Test button. Press PA, the IN-USE indicator will light, and then start to monitor door station connected circular with click of relay. T/RT/R+ PA S1 POWER P- P+ P- P+ •• JWB (IN1, IN2, IN3, IN4): Connected to door stations (Max.4). PA LINK JWP INUSE •• JWP: Power input. P+, positive 24V; P-, negative. ERROR Chapter 2 POWER C5-MDS •• S1: DIP Switch function setting, refer to DIP switch setting.
PAGE 31
S201 PA202 PA204 S201 LED204 PA201 PA202 PA203 PA204 LED204 LED203 DIP 1 2 3 4 5 6 LED202 ON •• LED201: Power indicator LED202 LED203 PA201 PA203 LED201 LED201 •• PA204: Reserved in normal status, for door station communication in test status •• LED202: Reserved •• LED203: Picture saving indicator •• LED204: Picture play indicator C5-IMC •• JWP101: Power input, DC 24V •• RS485: PC port.
PAGE 32
K5 System Parts •• LED1: Indicators for first group of card reader •• LED2: Indicators for second group of card reader JP-LK1 1 2 3 •• JWP: Power input, DC 24V •• RS485: PC port, to set the parameters of GP-LIFT BEEP LED WG1 WG0 P+12V 1 2 3 SNSN+ JP-LK2 LED2 LED1 JP-LK1 CN-DS1-1 CN-LK1 CN-RD1 LED1 JP-LK2 CN-DS1-2 CN-LK2 CN-RD2 LED2 EB+ EBN.
PAGE 33
•• Maximum 4 cameras can be connected to the CM-IPC Parts and functions •• JWP: Power input •• JWV: Video signal input CM-IPC •• JW/VP: Video signal input, connected to VT-QSW •• RS485: PC port.
PAGE 34
Chapter 2 •• K5 System Parts : Earth Ground •• V-: DC power output, Negative (20~27 adjustable) •• V+: DC power output, Positive (20~27 adjustable) •• VADJ: Output voltage adjustable •• LED: Working state indicator Specification •• Input Voltage: AC 100~120V (2.5A), 200-240V (1.5A) •• Input Frequency: 50~60Hz •• Rated Voltage: DC 24V •• Rated Current: 4.5A •• Working temperature: -200C~600C •• Dimensions: 97*159*37mm 2.3.4.
PAGE 35
Chapter 3 K5 SYSTEM CONFIGURATION 3.1 One Entrance without Network.................................................. 36 3.1.1 Layout........................................................................... 36 3.1.2 List of Accessories........................................................... 36 3.2 Multi Entrances without Network............................................... 37 3.2.1 Layout........................................................................... 37 3.2.2 List of Accessories..........
PAGE 36
Chapter 3 K5 System Configuration The K5 system is flexible to meet all kinds of need in different structure; installer can install the system they want according to the requirements. Below are the examples with different combination of the system. §§3.1 One Entrance without Network This is the most basic installation, it applies to buildings where there is only one entrance, without network, so it can be connected without C5-IPC. 3.1.
PAGE 37
§§3.2 Multi Entrances without Network It applies to the installation where there is more than one entrance in the building, without network. All door stations can call any of the monitors in the building; monitors in the building can view the door stations in turn or a specified door station. 3.2.1 Layout C5-F414 C5-F414 1 1 2 2 3 3 4 4 Floor N C5-F414 C5-F414 1 1 2 2 3 3 4 4 Floor 1 C5-IPC C5-IPC PS5 RVV 2*1.
PAGE 38
Chapter 3 K5 System Configuration §§3.3 One Entrance with Network Network connection is required when communication between different buildings or between buildings and Switchboard. C5-IPC is needed to effect the network connection. 3.3.1 Layout C5-F414 C5-F414 1 1 2 2 3 3 4 4 Floor N C5-F414 C5-F414 1 1 2 2 3 3 4 4 Floor 1 C5-IPC To LAN/WAN C5-IPC PS5 RVV 2*1.0 RF CARD 1 2 3 4 5 6 7 8 9 * 0 # CAT5 Cable Exit Button 3.3.
PAGE 39
§§3.4 Multi Entrances with Network It applies to the installation where there is more than one entrance in the building, with network. All door stations can call any of the monitors in the building; monitors in the building can choose to monitor all the door stations in turn or to select a specified door station. Also all door stations will be able to communicate with the Switchboard. 3.4.
PAGE 40
Chapter 4 K5 System Settings Chapter 4 K5 SYSTEM SETTINGS 4.1 Door station Setting................................................................ 41 4.1.1 Door station working mode.............................................. 41 4.1.2 IP-MR9L Configuration.................................................... 41 4.1.3 Configuration IP-MR18L.................................................. 49 4.2 Lock Connection..................................................................... 59 4.2.1 Lock Type......
PAGE 41
§§4.1 Door station Setting 4.1.1 Door station working mode Door station is to be installed in the entrance, to communicate with monitors or with Switchboard. Door station can be set to work under two modes: 1. Unit door station To be installed on the entrance of each separate building, being able to call all the monitors inside the building 2. Common door station To be installed on the common entrance, being able to call all the monitors inside the LAN network 4.1.
PAGE 42
Chapter 4 K5 System Settings 4.1.2.2 Program Menu overview •• Enter debug mode to over view all the menus and Tools Debug State Menu Item [1] Installer Setup [1][1]. DS Serial NO. [1][2]. Unlock Timing [1][3]. Unlock Output [1][4]. Card Memory [1][5]. Doorplate Mode... [1][6]. Audio Option... [1][7]. Parameters... [1][8]. Installer Code... [1][9]. Default Set... [2] Setup [2][1]. Language [2][2]. Tone Select [2][3]. Tone Volume [2][4]. Unlock code [2][5]. Code Check... [2][6]. Clock... [2][7].
PAGE 43
4.1.2.3 Basic program settings •• Installer Setup (Debug State->1.Installer Setup) Item Descriptions Factory Set 1. DS Serial NO. 0 ---- Set as Unit door station. No C5-IPC connected. Set to 0, then input 1/2/3 to select the related distributor type. 1. F411 ------> C5-F4 2. F414 ------> C5-F414 3. F422 -------> C5-F422 1~8 --- Set as Unit door station. C5-IPC connected. Only one door station connected: set to 1.
PAGE 44
Chapter 4 K5 System Settings •• Parameters(Debug State->1. Installer Setup->7. Parameters) Three pages are available inside the parameters, press # to switch between different pages Table 1 Item Descriptions Factory Set 1. Monitor Numbs To set number of monitors that can monitor the door station at the same time [2] 2. Monitor Timing To set the maximum monitoring time on door station [15] 3. Monitor & Talk Enble/Disable talk function when monitor is monitoring [1] Enable 4.
PAGE 45
Table 3 Item Descriptions Factory Set 1. Display Mode Reserved [0] 2. Camera Power-on To choose to power the camera always or to power only when door station is activated [0] Power when activated 3. Enable name list Enable/Disable namelist function [0] 4. Door Open Alarm reserved 5. Disable Intercom Enable/Disable intercom function between montiors 6. Protect Setup Reserved 7. Open Card Mode Reserved 8.
PAGE 46
Chapter 4 K5 System Settings •• Monitor Program (Debug State->3. Monitor Program). Access Monitor Program in Debug Mode (Also See 1.1, Access Monitor program in normal mode > > D E B U G S TAT E < < --------------------------1-# Installer Setup 2-# Setup 3-# Monitor Program 4-# Card Manage [3]Monitor Program --------------------------- [3]Monitor Program --------------------------- Old M.code New M.code Old M.code New M.
PAGE 47
[2] Delete Card Enter Delete by Card; >>[7][2] >>[7][2] Swipe the card to be deleted, and card number and Room Code will be shown after deleted Delete by Card Delete by Card Show the Card Card:15977131 M.code:0101 Updated #Save *Back Us C a er rd *Back #Save Video Entry System Video Entry System [3] Delete by M. Code >>[7][3] Enter Delete by M. Code; Input the Room Code, press “#” to confirm; all the cards attached to the User code will be deleted >>[7][3] Delete by M.Code Delete by M.
PAGE 48
Chapter 4 K5 System Settings 1. Volume Adjust Door station can adjust its talking volume by keypad. Note that the volume adjusting function is automatically activated in the Debug Mode. 2 0 - 0 8 0 6: 1 8 After Volume-Adjust is activated, if Door Station calls a Monitor and enters talking state, current volume values are shown on bottom line. The left value means the microphone volume of door station, and the right value means the speaker volume of the door station.
PAGE 49
4.1.3 Configuration IP-MR18L Door stations also can work in Normal mode and Debug mode. 4.1.3.1 How to enter debug mode >> Debug State << RF CARD 1 4 2 3 5 6 7 8 9 * 0 # [ **** ] 0-# Redial 1-# To o l s 2-# Exits Please Input Password When Door Station is standby, press “#” key Input “9008”, then input Admin Code (“66666666” by default) Debug Mode menu is launched 4.1.3.
PAGE 50
Chapter 4 K5 System Settings 4.1.3.3 Basic program settings •• Installer Setup (Debug State->1#->1.Installer Setup) Item Descriptions Factory Set 1. ID Code. 1.When there is only one door station and no C5-IPC, set to 0. And set the type of distributor used with it. When C5-IPC is connected, must not be set to 0. 2. When C5-MDS is connected, be set to from 1~8 according to which port it is connected on the C5-MDS 3. When used as common door station, set to 9 [0-11] Standalone Used with F411 2.
PAGE 51
•• Installer Setup (Debug State->1#->1. Installer Setup->7. Parameters) Three pages are available inside the parameters, press # to switch between different pages Table 1 Item Descriptions Factory Set 1. Monitor Numbs To set number of monitors that can monitor the door station at the same time [2] 2. Monitor Timing The maximum monitoring time [30] 3. Monitor & Talk Enable/Disable talk function when monitoring [1]: Enable 4.
PAGE 52
Chapter 4 K5 System Settings Table 3 Item Descriptions Factory Set 1. Unlock Code 2 Reserved None 2. Unlock Code Mode Reserved [0] 3. Camera Power-on To choose to power the camera always or to power only when door station is activated [0] Power when activated 4. Reserved Reserved 5. Disable Intercom Disable/Enable intercom function between monitors [0] Enable •• Setup (Debug State->1#->2. Setup) Item Descriptions Factory Set 1.
PAGE 53
•• Unlock by code(Debug State->1#->1. Installer Setup->7. Parameters) RF CARD 1 4 2 i Door Open RF CARD 3 5 6 7 8 9 * 0 # 1 [ **** ] 4 2 3 5 6 7 8 9 * 0 # Please Input Password When Door Station is standby, press “#” key Input 4 digits Unlock Code If verified correctly, door open •• Unlock code setting (Debug State->1#->2. Setup->4.
PAGE 54
Chapter 4 K5 System Settings 1.ID Code [0-11] 2.Unlock Timing[01] 3.Unlock Output[0] Installer 4.Card Memory [0] Setup 5.Doorplate Mode[0] Press1~9 6 . A u d i o O p t i o n s . . . to select 7 . P a r a m e t e r s . . . *Back Tools 8.Installer Code... 9.Default... 1. Installer Setup 2. Setup 3. Card Memory 4. Online Monitors 5. Online Devices *Back Card Memory 1 . A d d C a r d . . . 2.Delete By Card Press No. 3 . D e l e t e B y M . c o d e to select 4 . C a r d I n f o r m a t i o n 5.
PAGE 55
[1] Add User Card 1. AddCard ... 1. AddCard ... [----] [0101] C a r d numbs : 1 5 9 7 7 1 3 1 * Back Show The Card # Save * Back Us C a er rd # Save [0101] Show The Card Please Input Room Code * Back 1. AddCard ... Enter Add Card menu, and Room Code is asked. Input Room Code Read the card to be authorized [2] Delete User Card - Delete by reading card 2. Delete By Card ... 2. Delete By Card ...
PAGE 56
Chapter 4 K5 System Settings [4] Format Enter Format, input the installer setup password and # key, then all the information will be deleted about cards 5. Format 5. Format [--------] [--------] Please Input Password Please Input Password * Back i # Save Updated * Back # Save 4.1.3.4 Debug Tools >> Debug State << 4. Online Monitors 0-# Redial 1-# To o l s 2-# Exits Tools 1. Installer Setup [ - - - - ] ~ [- - - - ] 2. Setup 3. Card Memory 4. Online Monitors (Search Range) 5.
PAGE 57
1. Volume Adjust Door Station has the advanced feature that conversation volume of both directions can be adjusted in digital method. SW I T CH : 1 5 After Volume-Adjust is activated, if Door Station calls a Monitor and enters talking state, current volume values are shown on bottom line. The left value means “Door Station talks to Monitor” channel, and the right value means “Monitor talks to Door Station”. Each value can be adjusted separately, ranges for 01 to 25, and 15 by default.
PAGE 58
Chapter 4 K5 System Settings 4. Online Monitors search Function: Search the certain range of Monitor which is for checking the information of the online monitor. After startup this operation, the Door Station search and display the present online monitor according to the setup range automatically. Operation steps are show as below: >> Debug State << 4. Online Monitors 0-# Redial 1-# To o l s 2-# Exits Tools 1. Installer Setup 2. Setup 3. Card Memory [ - - - - ] ~ [- - - - ] 4.
PAGE 59
§§4.2 Lock Connection 4.2.1 Lock Type The door station can connect two kinds of lock: The power-on to unlock type: The lock stays locked when there is no power, and unlocks once it gets the power from the power supply. The power-off to unlock type: The lock stays locked when there is power feeding it , and unlocks once the power is cut off. 4.2.
PAGE 60
Chapter 4 K5 System Settings 4.2.2.2 Door Lock Controlled with External Power To C5-IPC or Distributor + - AC + - PS5 LK- +12V N.O LK+ EB+ EB- CN-LK T/R- T/R+ 3 2 1 RF CARD J/KMB 1 2 3 4 5 6 7 8 9 * 0 # CN2 CN1 Bus JP-LK POWER SUPPLY Remove the jumper Exit Button IP-MR18 Note: LOCK 1. Please use DC lock and the related DC power supply 2. Remove the JP-LK jumper 3.
PAGE 61
Inside call A call made from the unit door station is the inside call, the inside call can only call the monitor inside the building. Visitors input the address of monitor (4 digits: ABCD), the door station will call the monitor right away Outside Call Calls from the Switchboard or common door station are outside call. When making this call, 7 digits address is required: XXX-ABCD. XXX- represents the IP address of C5-IPC of the building ABCD-represents the address of the monitor 4.3.
PAGE 62
Chapter 4 K5 System Settings 2) Touch the User Setup icon to enter setup interface, password will be required, Input 2412 + to get access to the setup. 3) Now touch the User Code and input the new user code to be the address of the monitor.
PAGE 63
•• C5-AT16 1) In Standby Mode, Press the menu button on the surface of the front panel.
PAGE 64
Chapter 4 K5 System Settings 3) Now navigate to the Setup and press menu button to enter setup page Door Station Tone -- 01 Door Bell Tone -- 05 GuardUnit Tone -- 05 No Disturb Mode -- off Installation...
PAGE 65
5) Go to Room Address… Alarm In/Out Delay -- 40 Date And Time Set ... Room Address... Other Settings... Information...
PAGE 66
Chapter 4 K5 System Settings •• C5-AT25 1) In standby mode, press the Menu button 03/29/2012 Thu. 11 : 44 AM 2) In the Calendar page, press the menu again to enter main menu Main Menu Monitor ... Intercom Alarm Function ...
PAGE 67
3) Press the button to entry About page H/W : S/W: Voltage: Local Address: Remote Number: AL. Delay Time: Video Standard: T3-753 a1.2 V11.02.27 22.7V 1002 0 40/90 PAL Exit 4) Press the unlock button and hold for 3s when entry about page, then entry Installer Setup page, just like the following picture shows. Input 0080 then press Menu button to confirm, then entry room code setting status.
PAGE 68
Chapter 4 K5 System Settings 5) Now Set the new room address for the monitor navigation button, and press menu button to save the setting Code Number: 0010: delete remotes 0011: add remote 0020: set as door bell 0021: not door bell 0022: have door station 0023: no door station 0030: out-delay set 0031: in-delay set 0080: room id set 0090: test armed [1002] 0093: direct call gl vd on 0094: direct call gl vd off 8008: MM/DD/YYYY 8009: DD/MM/YYYY 8012: 12 hour format 8013: 24 hour format 2412: restore to d
PAGE 69
Step2: Activate call function on monitor •• C5-ATT27 Monitor Manual Intercom Direct Call Guard Unit Alarm Security Multimedia 1 2 User Setup 3 Intelligent Estate Home Management 4 Press Menu button twice to entry main page Close 09/08/2011 Tue. 09:58 Press Direct Call Guard Unit icon •• C5-AT16 2 TALK MENU MONITOR Intercom Function Call Guard Unit Direct Call Guard Unit Intercom Call Exit Press Call button to entry Intercom Function page Select Call Guard Unit.
PAGE 70
Chapter 4 K5 System Settings Step3: Upload Monitor Address(Monitor Code) === Monitor Program === Old M. code [ 0099 ] New M. code [ - - - - ] === Monitor Program === Old M. code [ 0099 ] New M.
PAGE 71
Distributor type SW1 setting C5-F4 F4/F4DV/F4Q C5-F422 F4/F4DV/F4Q C5-F414 F4/F4DV/F4Q 4.4.2.2 DIP switch setting S1 is a 6-bit DIP switch; each of them is designed to have a specified function. •• DIP status Each bit can be set to be ON or OFF, shows below: ON(1) ON = OFF(0) ON = ON 1 2 3 4 5 6 •• Description of DIP switch Bit NO.
PAGE 72
Chapter 4 K5 System Settings 4.4.2.3 IP Address Setting C5-IPC must be specified an IP address in the network system. And every specified IP address must be unique. You can use IP8210Config software to set IP. NOTE: The default IP address of C5-IPC is 192.168.0.2 Setting steps as follows: 1. Connect C5-IPC and PC, and set IP address of PC to 192.168.0.X Assume that PC IP is 192.168.0.105 IP: 192.168.0.
PAGE 73
3. Search the connected C5-IPC Click Search... to start searching the connected C5-IPC 4. Config IP address Select the Device in the Device List Frame 5. Click on Config to config IP Assume it’s set to 192.168.0.
PAGE 74
Chapter 4 K5 System Settings NOTE: 192.168.0.1 & 192.168.0.255 cannot be used by any device in the network. 192.168.0.1 192.168.0.255 •• IP address range of C5-IPC AG S1 ON POWER DIP PA LINK 1 2 3 4 5 6 VR600 + IN-USE 192.168.0.2 ---- 192.168.0.239 1 2 3 SW1 P+ P- P+ P- RS485 JWB(IN) JWB(OUT) CN(MDS) ETHERNET C5-IPC •• PC IP address IP8210Config 192.168.0.2 192.168.0.3 ---- 192.168.0.254 PC Because default IP address of C5-IPC is 192.168.0.
PAGE 75
4.4.2.4 Parameters Settings All the parameters of C5-IPC can be set through IP-Device. See IP-Device manual for detail. 4.4.2.5 Controller Concept Controller in the system serves as the controlling center, it controls data communicating, audio and video distribution. Of all the devices, Door station and C5-IPC can be set to be the controller. Rules must be followed as below: 1) There must be one and only one controller in the system.
PAGE 76
Chapter 4 K5 System Settings 4.4.2.
PAGE 77
Work with C5-F422 Note that VD-SET must be set to VD if the C5-F422 is the last one of the bus HI / VD To Next PS5 To Next C5-F422 - To other monitors + 1 T/RT/R+ INUSE ON LINK S1 PA ERROR P- P+ P- P+ POWER P- P+ P- P+ 2 C5-AT27 C5-F422 VD-SET 1R GD PORT-A PORT-B PORT-C PORT-D 2W 3Y 4B T/R+ VD FV+ T/R- FV- P-D1&D2 Z1 Z2 Z3 AU P- Z4 COM P+ COM P+ PR 1 JWB(IN) JWB(OUT) 2 3 VD-SET(L=HIGH) 4 PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT) HI / VD - To other monito
PAGE 78
Chapter 4 K5 System Settings Work with C5-F414 Note that VD-SET must be set to VD if the C5-F414 is the last one of the bus HI / VD To Next PS5 To Next C5-F414 - To other monitors + 1 T/RT/R+ INUSE ON POWER S1 PA ERROR P- P+ P- P+ LINK P- P+ P- P+ 2 C5-AT27 C5-F414 VD-SET 1R GD PORT-A PORT-B PORT-C PORT-D 2W 3Y 4B T/R+ VD FV+ T/R- FV- P-D1&D2 Z1 Z2 Z3 AU P- Z4 COM P+ COM P+ PR 1 JWB(IN) JWB(OUT) 2 3 VD-SET(L=HIGH) 4 PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OU
PAGE 79
Work with C5-MDS This example contains the full function available in the system: Multi entrances with C5-MDS; Monitor display network video; and one of the monitor serves as Guard Monitor.
PAGE 80
Chapter 4 K5 System Settings Work with Common Door Station Door station can be set to function as common door station, being able to call all the monitors in the network system, while unit door station can only call the monitors of its own building.
PAGE 81
§§4.5 C5-MDS Setting ON 1 DIP 2 3 4 5 T/RT/R+ S1 ERROR LINK RS-485 POWER PA S1 LINK P- P+ P- P+ PA INUSE JWP ERROR C5-MDS is used where there are more than one door stations in one block, to serve as door station switch, to separate Audio, video signal form or to different door station. 6 IN-USE POWER C5-MDS JWB(IN4) JWB(IN3) JWB(IN2) JWB(IN1) JWB(OUT) JWB(IN4) JWB(IN3) JWB(IN2) JWB(IN1) JWB(OUT) 4.5.1 Port Description Please refer to 2.3.4.
PAGE 82
Chapter 4 K5 System Settings ON(1) ON OFF(0) ON = ON = Note: 1 2 3 4 5 6 Bit1 and Bit2 are for address purpose, the rest are reserved for late use. DIP1 DIP2 C5-MDS Address OFF OFF The first C5-MDS ON OFF The second C5-MDS OFF ON The third C5-MDS ON ON The fourth C5-MDS 4.5.2.
PAGE 83
4.5.
PAGE 84
Chapter 4 K5 System Settings §§4.6 Accessory Parts 4.6.1 Distributor Distributors serves as a branch, they are connected in hand-in –hand-out style in the BUS(BUS comes out from the door station or from C5-IPC), and function to separate the audio and video signal from the bus to the monitors, and also power the monitors. Each Distributor has 4 outputs for the monitors. There are 3 types of distributor available in the system. 4.6.1.
PAGE 85
•• Distributor to C5-IPC Note that VD-SET must be set to VD if the C5-F422 is the last one of the bus HI / VD To Next PS5 To Next C5-F422 - To other monitors + 1 T/RT/R+ INUSE ON LINK S1 PA ERROR P- P+ P- P+ POWER P- P+ P- P+ 2 C5-AT27 C5-F422 VD-SET 1R GD PORT-A PORT-B PORT-C PORT-D 2W 3Y 4B T/R+ VD FV+ T/R- FV- P-D1&D2 Z1 Z2 Z3 AU P- Z4 COM P+ COM P+ PR 1 JWB(IN) JWB(OUT) 2 3 VD-SET(L=HIGH) 4 PORT-A PORT-B PORT-C PORT-D JWB(IN) JWB(OUT) HI / VD - To othe
PAGE 86
Chapter 4 K5 System Settings 4.6.1.2 Distributor Types There are 3 types of distributors in the system: C5-F411, C5-F422 and C5-F414.
PAGE 87
•• Large Capacity: The C5-IMC can save up to 800 pieces of pictures •• Flexible time setting: When browsing the pictures on the monitor, the switching time between different pictures can be changed on the C5-IMC •• Automatic room releasing: When the memory is full, the earliest pictures will be deleted to make room for the new pictures .Also users can delete the pictures by themselves on the monitor. 4.6.2.1 Connection Schematic Connect the C5-IMC as you do a distributor.
PAGE 88
Chapter 4 K5 System Settings 4.6.3 Access control-GP-ACS GP-ACS is access controller. It can work as a standalone access controller or work with C5-IPC to be connected to the network.
PAGE 89
4.6.4 Camera control-CM-IPC CM-IPC is a device designed for Network camera. Through the CM-IPC, the computer can display the video of the camera connected to the CM-IPC using the software IP-Agent. •• Auto Switching: The IP-Agent can display the different cameras by itself; the video also can be set to show different cameras by turn. •• Multi-camera: Maximum 4 cameras can be connected to the CM-IPC by applying VT-QSW.
PAGE 90
Chapter 5 K5 System Softwares Chapter 5 K5 SYSTEM SOFTWARES 5.1 PC Station Installation............................................................. 92 5.2 IP Address Setup.................................................................... 96 5.2.1 General Rules for IP Address Setup................................... 96 5.2.2 IP Address Setup by IP8210-Config................................... 96 5.2.3 IP Address Setup by IP Device Software........................... 101 5.3 IP Device 2012..............
PAGE 91
5.4.7 Setting........................................................................ 139 5.5 IP Access 2012..................................................................... 144 5.5.1 Introduction................................................................. 144 5.5.2 Login.......................................................................... 144 5.5.3 Access Device Console................................................... 146 5.5.4 Card Console . ................................................
PAGE 92
Chapter 5 K5 System Softwares §§5.1 PC Station Installation 1. Double Click Setup.exe. Start to install PC Station. 2. Select language, and then click next.
PAGE 93
3. Click Next 4.
PAGE 94
Chapter 5 K5 System Softwares 5. Click Install button to begin the installation, then waiting till installation finishes. 6.
PAGE 95
7. Please note the default login info: ID: Device Password: 123456 Server Name: Machine Name + ‘\K2012’ Database Name: K2012 Customers need to enter the Server name and Database name.
PAGE 96
Chapter 5 K5 System Softwares §§5.2 IP Address Setup For constructing a DEDICATED LAN for IP system, all network devices must be set to different IP Address. •• Network device model includes C5-IPC, IP-G21 and CM-IPC and PC Station. •• All network devices can be detected by IP8210 Config and IP-Device, but only C5-IPC and IPG21 and CM-IPC can be set by these two software. PC Station is set by Windows IP setup. 5.2.1 General Rules for IP Address Setup All the devices must be in the same IP Segment.
PAGE 97
2. Press icon in the notification area. It will pop up a window for setting network. 3. Press Properties button in the Local Network Status window 4. Select Internet Protocol(TCP/IP) item in the Networking tab of Local Network Properties window 5. Select Use the following IP address option in the General tab of Inter Protocol Version (TCP/IP) Properties window 6.
PAGE 98
Chapter 5 K5 System Softwares 5.2.2.2 Connect device to PC directly or network The following is a diagram of direct connection: PS5-24V 2 Wire C5-IPC CAT5 Ethernet 5.2.2.3 IP8210 Config Software Run the IP8210-config Page 98 K5 System Technical Guide IP8210 Config.
PAGE 99
1. Press Search… button to search the device. You can press Stop button to end the search after the device has been detected. Just like the following picture shows. 2. Select the device in the Device List frame, then press Config button.
PAGE 100
Chapter 5 K5 System Softwares 3. A window will pop up for IP address setting. Modify IP address, but remember to leave the Mask and Gate as it is, and then press OK button to confirm. Its Mac address will be automatically modified simultaneously. 4. If setup is successful, it will pop up a window to inform you. Press OK to confirm.
PAGE 101
5.2.3 IP Address Setup by IP Device Software An IP setup tool has been inserted in IP Device software. The function is the same as IP8210-config software. Install PC Station package software. And IP Device software shortcut will be created automatically in the desktop. 5.2.3.1 Set PC Station IP Assume using the following IP address IP address: 192.168.0.246 Subnet mask: 255.255.255.0 Default gateway: 192.168.0.1 Note: IP address range of PC station must be from 192.168.X.241 to 192.168.X.246.
PAGE 102
Chapter 5 K5 System Softwares 5.2.3.3 Set IP Address 1. Start IP Device software 2. Right click on K5 System, then select IP Node Config in the pop-up menu 3.
PAGE 103
4. Then it will pop up a window to show devices that are detected. Assume that 192.168.0.80 is the device that is supposed to be set to 192.168.0.82 5. Double click 192.168.0.80, then a window pops up for modifying IP, input 82 then Mac address will be automatically modified. Press OK button to confirm modification.
PAGE 104
Chapter 5 K5 System Softwares 6. A window will be pop up to inform you if config succeed, just like the following picture shows. Press ‘OK’ to confirm §§5.3 IP Device 2012 5.3.1 Introduction IP Device is used to construct a new project and save project information to a database for IPAgent whose information is based on the database. It can set the parameters of C5-IPC on-line. 5.3.2 Login •• Start the IP Device 2012 Software icon that has been created automatically. IP Device gets starts.
PAGE 105
•• Check the information, then Click Login to access IP Device. File: Include Change and Password and Exit. Language: Include English and Chinese (Simplified).
PAGE 106
Chapter 5 K5 System Softwares 5.3.3 Project Property •• Right click on Default Project, then it will pop up a menu. Select Project Property •• It will pop up a window for setting project property.
PAGE 107
IP Seg: Select a IP Segment for the new project. Note that all the IP address must be in the same segment.We will take 192.168.0.X as an example in this manual System Type: IP-device can be used in DT or C5 system, here we choose C5. Project Name: Name of the new project; we will name K5 System as an example in this manual Project Description: Can input some info about project Project Mark: Can input some info about project Insert time line: Insert the created time in K5 System frame.
PAGE 108
Chapter 5 K5 System Softwares Model Description Model Name Model Description C5-IPC_CDS C5-IPC for Common Door Station C5-IPC_DS C5-IPC for Door Station CM-IPC IPC for CCTV Camera IP-G21 Guard Unit PC PC Station( IP-Agent ) For example, in K5 System, see the table, IP Nodes can be configured like the following picture IP Device 192.168.0.(81/82/84/86) Door Station: A Block/B Block /C Block /D Block 192.168.0.(83/85) Common Door Station: Common Entrance 1/Common Entrance 2 192.168.0.
PAGE 109
After adding the devices to the project, Click on Save to exit. Also, if all the decivices are installed in the system, we can click on Scan&Check to search the devices on-line, and then added them to the project.See below: Now go back to the mian interface, and here we can see the project and all the devices added To it .
PAGE 110
Chapter 5 K5 System Softwares If you want to check if the devices are online, you can press Refresh Online button or click right mouse button on K5 System then select Check Network Device Online. See the following picture, means PC is online, but IP-Agent isn’t opened, means device offline, and indicates the model of IP Node is wrong selected, or wrong DIP switch setting of C5- IPC.Note that, the Refresh Online checks only the IP-Node, such as C5-IPC, PC station and IP-G21. 5.3.
PAGE 111
Assuming that we have that 4 door stations and 8 monitors in each block. And door staions coded from 1~4; monitors coded from 0021~0024 and 0031~0034. •• Door station Configuration DS Config: Right click on A Block -> Select DS Config on the pop-up window -> Config just like the following picture -> Click Save button to confirm -> Then the software will check if the door stations just added are on line or not.
PAGE 112
Chapter 5 K5 System Softwares We can use Add or Batch Add to add monitors. Add is to add monitors one by one, while Batch Add enables you to add monitors in batches. When all the monitors are added. Click close to save and exit. Now go back to the block interface, and right click on A Block -> Select Check IM Online on the pop-up window-> Software will check if the monitors are online automatically. Just like the following picture shows.
PAGE 113
•• Extended Monitor Configuration Maximum 3 monitors can be set in one apartment. One of them is Master and the other 2 slave monitors. Now assume that we want to add slave monitors to the A block 0021 monitor, right click on A Block-0021 ->Select Extend Monitor Config on the pop-up window ->Config just like the following picture-> Click Save button to finish. -> Software will check if the monitors are online automatically. Note that only 2 extended monitors are valid in the system.
PAGE 114
Chapter 5 K5 System Softwares Guard Center Priority: When block givs out call, to set how the calll is transferred to different switch boards Even UP Setting: When block gives out alarm signal, to set how many guard centers it will go to Input Table: To make a name list for all door stations and montiors and switch boards IP Table: To make a name list for all block(C5-IPC) and swithc boards( IP address list) 5.3.6.
PAGE 115
5.3.6.2 Event up Setting Event here has to do with the monitors. Events such as defense-enabling/disabling, emergency call, and alarm signal will be sent to all the switch boards in the list. After the setting , click Save button to finish setup and Write to all device to set all the C5-IPC connected. 5.3.6.3 Input table Input table is to make a name list for all the monitors and door stations and switch boards in the system.
PAGE 116
Chapter 5 K5 System Softwares Here please note that: 1. Switch can call any of the devices directly by their name. 2. Common door stations can all any one of monitor by their name. 3. Door stations and monitors can not choose to call different monitors, should see Guard center priority. 5.3.6.4 IP Table The IP Table is a name list for all the devices which have IP address, such as C5-IPC and switch boards. And when call the devices, we can use the name instead of the IP address.
PAGE 117
5.3.7 Management of Block C5-IPC The management of C5-IPC provides access to all the parameters of a C5-IPC, the different parameters can be set, changed and saved according to different requirements on each of the C5-IPC.
PAGE 118
Chapter 5 K5 System Softwares 1. Local Call Table: To make namelist for the monitors inside the block. The door station can input the specified number to call the monitor. - View&Edit: To make and edit the call table - View on device: to view the call table of the device 2. IP Call Table See IP Call Table in the previous chapter. 3. Call Priority The call priority here, unlike the Call Priority setting in Default project parameters, is to set the priority for each C5-IPC.
PAGE 119
Here we can choose to Use Project Default, refer to previous chapter Default project parameters. Or we can untick the item, and set the Call priority manually. Maximum 8 Guard centers can be set for each C5-IPC. 5.3.7.
PAGE 120
Chapter 5 K5 System Softwares 1) General Number of Monitor: How many monitors can monitor the door station at he same time, ranging from 1~5 Talk On Mon: Enable/Disable the talk function when monitor is doing monitoring Unlock On Mon: Enable/Disable the unlock function when monitor is doing monitoring IM Monitor Time: To set Monitor Time from IM monitor to Door Station, ranging from6~600s Call Wait Time: To set calling waiting time from door station to monitor.
PAGE 121
3) Event up Event up setting decides which switchboard should the alarm and events be sent to. We can adopt the default setting, or untick to set the switchboard we want. Maximum 4 switchboards can be set to one C5-IPC, and the events will be sent to all the switchboards at one time. 4) MDS MDS serves as multi- door station switcher. When there are more than one door station in one block, it must be used to make the system work properly. The system now allows maximum 2 C5MDS to work at one block.
PAGE 122
Chapter 5 K5 System Softwares does the monitoring. It always surveys camera port , skips the door station port when off line and skips None port always. 5) Monitor Monitor Switch Timer: Set the time duration of each port when do monitoring on the monitor Monitor 1~8: Set the channels available when do automatic monitoring on the monitor, it switches from one to another by turn 6) Advanced •• IP8210 control This item is reserved, don’t change the setting easily.
PAGE 123
7) Dip Statues This information is uploaded from C5-IPC device DIP switch setting; it just can be changed on C5IPC. For more details, refer to C5-IPC settings in part 4. 5.3.8 Management of Common C5-IPC The Common C5-IPC is set to work with Common door station, and common door station is able to call all the monitors in the system.
PAGE 124
Chapter 5 K5 System Softwares 5.3.8.1 Call Table Common Call Table: See Input Table in 5.3.6. IP Call Table: See IP Call Table in 5.3.6. Call priority: See Call Priority 5.3.6. 5.3.8.2 Parameters setting Call Wait Time: To set calling waiting time for door station and m o n i t o r, R a n g i n g from 10 to 600s.
PAGE 125
•• IP8210 control This item is reserved, don’t change the setting easily •• Call Table Quan Rows of Common Call Table: To set the limitation of rows when making the Common call table Rows of IP Table: To set the limitation of rows when making the IP call table Rows of Room Call Table: To set the limitation of rows when making the Local call table 5.3.9 Tip Device Tip Device is debug tool to find the physical C5-IPC.
PAGE 126
Chapter 5 K5 System Softwares 2) Press the PA key of the related C5-IPC, A window will pop up showing the IP address of the C5-IPC. §§5.4 IP Agent 2012 5.4.1 Introduction IP-Agent is the main software of PC Station. It’s a Switchboard that enables you communicate with user, entrance of blocks, common entrances and other Switchboards in one residential area via IP network. •• Unlock door when talking with entrances or monitoring.
PAGE 127
3. Enter the Server name and Database Name Server name: machine name + ‘\K2012’ Database Name: K2012 It is strongly recommened that the password should be changed via IP-Admin. Otherwise it may cause information leak and the responsibility is on the user. 5.4.3 Operate Interface Input the correct User ID, Password, Server Name and Database Name, It will pop up the window of operate interface. Just like the following picture shows.
PAGE 128
Chapter 5 K5 System Softwares Item Description 1. S/W Title Bar Display the name of the software 2. ID Shows the user ID 3. Monitor Launches the Monitor Viewer. 4. Record Launches the Record Viewer 5. Capture Launches the Capture Viewer 6. Setup Open the setup page 7. Exit Terminates the application 5.4.4 Monitor Viewer From the right upper corner of the IP-Agent main screen, click the [Monitor] tab. 5.4.4.
PAGE 129
Item Description 1. Device List Consists of 4 parts: GL & PC, DS & CDS, Monitor & Camera 2. Call List Call info record 3. Alarm Alarm and events record 4. Unlock 1 Unlock the latch of the entrance 5. Unlock 2 Unlock the latch of the entrance 6. Capture Capture a picture of the selected video window 7. Record Performs/Stop Recording the selected video window 8. Digital Keypad Open digital keypad for operation 9. Exit Exit monitoring 10. Maximum Maximize the monitoring screen 11.
PAGE 130
Chapter 5 K5 System Softwares Item Description 1. Monitor Time Displays the monitor time elapsed 2. Device Name Displays the name of the monitored device 5.4.4.3 Name & Function in Pop-up Call Window It will pop up a calling window for video and operation when there is a calling to DS/CDS or an incoming calling from DS/CDS. 8 1 2 3 4 5 6 Item 7 Description 1. Capture Capture a picture of the video window 2. Record Performs/Stop recording the video window 3.
PAGE 131
5.4.4.4 Device List Device List consists of 4 parts, including GL & PC, DS & CDS, Monitor and Camera. After device configuration operation in IP Device software, all the devices that have been configurated in IP Device will show in the Device List. Icons & Description: 1. : Device Online 2. : Device Offline 3. : PC Online, but IP-Agent is not running 4. : Invalid Model 5. : Call 6. : Monitor •• GL & PC GL & PC is a list of Switchboards, including Guard Station and IP-Agent.
PAGE 132
Chapter 5 K5 System Softwares 2) Incoming Call 1) Press Accept to enter talking status, else press Refuse to deny the calling 2) Talking established after accepting the calling, you can press Hand up button to end the conversation •• DS & CDS All the door stations & common door stations are listed in this frame. You can input full or part of a device name to search one DS or CDS in the Search input box.
PAGE 133
2) Incoming Call 1) Press Accept to enter talking status, or else press Refuse to deny the calling. 2) Talking established after accept the calling, you can press Hand up button to end the conversation. 3) Monitor Press button to monitor the related DS or CDS. The video will be shown in the focused monitor window. •• Monitor All the monitors of one selected building are listed in this frame.
PAGE 134
Chapter 5 K5 System Softwares 1) Call and wait for picking up 2) Talking established if the called Switchboard picks up 2) Incoming Call 1) Press Accept to enter talking status, else press Refuse to deny the calling •• Camera You can connect one camera to IP Network via CM-IPC.
PAGE 135
•• Call List Click the Call List tab to unfold the lists. Call List is a record that includes call destination/call source, date, time and length of time Icons & Description of Sub Lists 1. (All Call): All call info including outgoing calls, incoming call, missed calls 2. (Calls): Outgoing call info 3. (Incomings): Incoming call info 4. (Missed calls): Missed call info Double click one record to call the related destination All Calls Outgoing Calls Incoming Call Missed Calls 5.4.
PAGE 136
Chapter 5 K5 System Softwares Item Description 1. Record List Includes audio record, video record and talking record 2. Video Screen Displays video/audio record 3. Record Controller Controls record playing 4. Progress Bar Shows the playing progress when playing record 5.4.5.2 Name & Function in The Record Window 2 1 Item Description 1. Device Name Displays the recorded device name 2. Record Time Displays the time when the video/audio was recorded 5.4.5.
PAGE 137
Icons & Description 1. (All Record): All record including audio record, video record and talk record 2. (Audio Record): Audio record for conversation between IP-Agent and monitor (based on setting), no video. 3. (Video Record): Video record for DS/CDS when monitoring (based on setting), no audio. 4. (Talk Record): Talk record for conversation with video. 5. (Record Filter): Filter record ased on specific time and address. Double click to select one record to display in the video screen.
PAGE 138
Chapter 5 K5 System Softwares 5.4.6 Capture Viewer 2 3 1 5 4 Item Description Captured Picture List Click to select the specific picture Record Filter Filter record based on specific time and address Video Screen Displays captured pictures Slide bar Slide to adjust the number of pictures that can be viewed simultaneously in the video screen Scroll bar Slide to browse other pictures TO View Big Picture Select one picture in the captured picture list.
PAGE 139
BROWSE MODE BIG PICTURE MODE If you want to back to BROWSE MODE, just double click on one picture in the video screen. 5.4.7 Setting From the right upper corner of the IP-Agent main screen, click the button to enter setting page. 5.4.7.
PAGE 140
Chapter 5 K5 System Softwares Title OSD Time: Show time in video window when monitoring or calling Name: Show device name in video window when monitoring or calling IP IP: Select the local machine address Camera IP: Input IP Address of IP-Agent camera（CM-IPC） Use IP Camera in IM call: Transmit video of IP-Agent camera to the called monitor Use IP Camera in GL call: Transmit video of IP-Agent camera to the called Switchboard Capture Capture Path: Select a path to save all captured pictures Record Record Pa
PAGE 141
Region Name Each of the 8 alarm regions can be set to its name. And when alarm trigger, the IP-Agent will show the name of the region.
PAGE 142
Chapter 5 K5 System Softwares Play time: how many times the alarm sound is played Ignore Time: A certain period of time after which the alarm tip/window will be disabled when there In no answer on the PC. 5.4.7.3 View & Layout Channel On Start : Layout: To set initial aspect ratio for video screen when IP-Agent gets start Channel Number: To set initial channel number for video screen when IP-Agent gets start Enable Max Channel: Deselect the option to disable 9 and 12 channel selection in the main frame.
PAGE 143
5.4.7.4 Handset Handset: Add one handset to IP-Agent Use handset: Enable a handset Com Port: Select related com port for the connected handset Ring Sound: Select a Ring Tone for handset Ring Volume: Adjust Ring Volume for handset 5.4.7.5 Security & Startup Password Control For Setting Select the Enable item, input the password and confirm it. If you want to change the setting, you must input the correct password.
PAGE 144
Chapter 5 K5 System Softwares §§5.5 IP Access 2012 5.5.1 Introduction IP Access 2012 is responsible for the maintenance and management of access control system to the whole management software, which can add access controller (C5-IPC), add/delete cards, back up and restore cards information, also check the pass record. Operating tools: Access controller gets card information Via Door Station and RFID link USB. 5.5.
PAGE 145
- The default password can be exposed to a hacking thread so it is recommended to change the password by IP-Admin software after installing the product. Otherwise the users are responsible for any information leak. - The following are two examples of login failure; you will see the error messages if input wrong information. Input incorrect ID or Password Input incorrect Server Name or Database Name 3) When successfully login the system File: Include Card Type, Change Password, Change Account and Exit.
PAGE 146
Chapter 5 K5 System Softwares 5.5.3 Access Device Console Click on Access Device Console into setting interface, just like the following picture shows 5.5.3.1 Cards information (Device) Valid Cards: Cards those have been added to theC5-IPC and are able to open the door Unregister Cards: Cards added via door station directly, but PC doesn't have these cards info. Click Process button to add these cards info to database in PC. New Event: The number of new records of card access.
PAGE 147
Not Downloaded Cards: Cards that have been inputted into database in PC but haven't been downloaded to the related device. Event Record: Card access record that has been saved in PC. Click on View Events to view card access records that include card number, access time, related room number and whether pass granted or not. 5.5.3.3 Utilities Import cards from file to device: Click Import Cards to import a backup file suffixed by CDF to the related device.
PAGE 148
Chapter 5 K5 System Softwares Property: The device information, include device address, hardware versions, software version and timer. Just like the following picture shows Refresh: Refresh all the info in this page. Download All: Download all the cards in the database to their related device respectively Refresh all: Refresh all devices to check if it’s online Close: Exits current window 5.5.3.
PAGE 149
5. Set clock: Synchronize the device time by PC time 6. Set pass rule: Set pass rule for device.( Retails refer to setting rule section) 7. View Pass Rule: View the pass rule in the device 8. Search: Search all the devices to check if it’s online 9. Set Clock All: Synchronize time of all devices by PC time 10. Set Pass Rule All: Set Pass Rule for all devices 11. Check online all: Check all devices if it’s online 12.
PAGE 150
Chapter 5 K5 System Softwares 5.5.4 Card Console Click Card Console into setting interface, just like the following picture shows. 5.5.4.1 Browse Display all card information in detail, including the card No, Remark, Card Person, Card type, room No, whether downloaded or not, and added time and operator.
PAGE 151
Fill the text boxes with card info in the Card Information frame. Card NO: Two methods: 1) Inputted Card NO by keyboard manually 2) Filled automatically by swiping the card over card reader(USB card reader) Room No: Input the related room Remark: Remark info for card Card type: Choose the type of card (User/control) Remember Last: Enable keeping all the card info of last card except card NO Batch Mode: Enable batch adding for cards Auto Download: Enable auto-download.
PAGE 152
Chapter 5 K5 System Softwares Click Filter item, It will pop up a window, just like the right picture shows. Record Count: Choose the max number of the card. Saved Filters: Save the filters for quick start next time. Create a new filter Edit the selected filter Delete the selected filter Save filter info Field Name: include all the info of cards.
PAGE 153
Auth +: Add the selected card to other authorized C5-IPC Re Auth: The selected card will be diverted to other authorized entrances. And the card info will be deleted in the original entrances automatically Event: Access records of cards 5.5.5 Pass Rule Pass Rule can be useful for real estate management. Pass rule is valid only with control card which is designed for management stuff of a residential area.
PAGE 154
Chapter 5 K5 System Softwares Click Save, set Rule 1 success. Rule 2 ~ Rule 6 settings refers to above-mentioned operation. If you want to download the rules to all devices, click Download to all devices button If you want to download the rules to one specified device, setting method refers to Access device configuration->device management->(Set Clock/Set Pass Rule) Click Close exits current setting window 5.5.6 Report Click on Report, enter Report interface, just like the following picture.
PAGE 155
Click Print to print report card, click Export to export a report document.
PAGE 156
The technical guide will be changed without notice. Right to interpret and copyright will be reserved(2012.