ENGLISH VIDEO INTERCOM SYSTEM AT16/C5-AT16 USER MANUAL 2 TALK MENU MONITOR VERSION 1.
Precautions ●● Slots or openings in the back of the monitor, are provided for ventilation and to ensure reliable operation of the video monitor or equipment and to protect if from overheating. These openings must not be blocked or covered. The monitor should never be placed near or over a radiator or heat register and should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided. ●● All parts should be protected from violence vibration.
Contents 1. Parts and Functions........................................................................ 1 2. Basic Door Release Operation....................................................... 2 3. Intercom Function.......................................................................... 2 4. Basic Setup Instructions................................................................. 3 4.1 How to Enter Main Menu Page................................................ 3 4.2 Ring Tone Settings.....................
1 1. Parts and Functions 1 2 7 11 3 4 2 12 8 9 TALK MONITOR MENU 5 6 AT16 hasn’t this terminal. 10 AT16 or C5-AT16 back view Key Functions 1. Microphone ●● Receives sound from the user. 2. LCD screen ●● Display the images from outdoor station.Touch operation. 3. LED indicator ●● ●● Normally light on when power on Flash when receiving signal or activating No disturb mode 4. Call key ●● Press to activate the intercom function page. 5.
2 2. Basic Door Release Operation 1. Input room numbers in Door Station of the building or main entrance, the Monitor rings, at the same time, the screen displays the visitor image. 2. Press TALK Button on monitor, you can talk with the visitor for 70 seconds. During communication, press TALK Button again to end the conversation. If nobody answers the phone, the screen will be turned off automatically after 40 seconds. 3.
3 Intercom Call: you can call the other users in the 3. same network with you. Input the building code and room number by using ▲ / ▼ Button to increase / decrease the value; use Button to select next digit; After finish, press Talk Button to active the calling, a call message will be sent out, if the system is free, you will heard the feedback rings, you can talk with someone who answers the call.Press Button to return Intercom Function page. 4. Basic Setup Instructions 4.
4 4.3 NO Disturb Mode If you don't want to be disturbed (for example, at night), set this item is on(use / button to choose on/off), any call from the outdoor station will be sent to the guard center, and the guard person will tell the visitor that you do not want to accept the visit. 4.4 Date and Time Setting 1. 2. Select item on main menu page to enter setup page,then use ▲ / ▼ button to select Installation... item. A password will be asked before enter next sub menu.
5 4.6 Restore to Default According to 4.4 , select Information... item, this item will show the hardware/software version and voltage information of the Monitor. Select Restore to default item ,then press MENU button. All settings will be restored to default.(Note that the restore to default operation will not change the time setting and the datas.) Hardware Ver. A1.2 Software Ver. V8.9 Voltage 25.6 Manufacture AT16 Restore to default Exit 5.
6 6. Defense Alarm Operation(optional) This system have auto-alarm function to ensure the security for the house owner. Total 4 different sensors were placed to protect different defense area. When the sensor was triggered, the monitor will sent out alarm sound immediately and will sent the alarm signal to the guard center at the same time. Note that your system may not have all the 4 sensors according to the system configuration.
7 3. Out-Delay Period: after you arm the system, you will get into Out Delay Period, monitor will sent out short “Di” every 3 seconds; you will hear a long “Di~” at the end of the Out Delay Period, and the system is gotten into the protecting status. By default, the Out Delay Period is 40 seconds, users must get out off the room within 40 seconds, otherwise the system will treat the user as a invader and sent out the alarm signal. 4.
8 NOTE: 1. Remote control distance is normally up to 30 meters, and will extend if the built-in telescopic antenna is taken out. 2. If the controlled distance is becoming shorter, or LED doesn't light on while pressing any button, open the remote control unit and replace the battery with a new one. 8. Specifications ●● Power supply for indoor monitor: DC 15~18V (supplied by system) ●● Power consumption: Standby 1W; Working status 5W ●● Monitor screen: 3.
Please read this manual carefully before using the product you purchase, and keep it well for future use.We reserve the right to modify the specification in this manual at any time without notice. VERSION 1.
