VisiDoc-It™ Imaging System Installation and User Instructions VisiDoc-It with Stand VisiDoc-It with Hood UVP, LLC 2066 W. 11th Street Upland, CA 91786 Phone: (800) 452-6788 / (909) 946-3197 Fax: (909) 946-3597 Ultra-Violet Products Ltd. Unit 1, Trinity Hall Farm Estate Nuffield Road, Cambridge CB4 1TG UK Phone: +44(0)1223-420022 Fax: +44(0)1223-420561 Web Site: www.uvp.
VisiDoc-It Imaging System 2 System Introduction The VisiDoc-It Imaging System is designed for researchers who already have a transilluminator in the lab. Configurations include a compact hood or camera stand. The compact hood fits on top of UVP’s High Performance and Benchtop Transilluminators.
VisiDoc-It Imaging System 3 VisiDoc-It with Stand Camera Stand with X/Y Movement Camera and Lens Kit EtBr Filter is mounted under the Lens 8” LCD Touch Screen Transilluminator with UV Blocking Cover (check the packing slip to determine if the system includes a transilluminator) USB Drive System Processor
VisiDoc-It Imaging System 4 System Specifications Camera The VisiDoc-It includes the FluorCam 210 Camera with a resolution of 640 x 480 (VGA) and a USB 2.0 PC interface. All camera settings are factory pre-set for optimum performance when viewing gels, films, or membranes under low light level conditions. UVP Technical Support should be contacted before making any adjustments to the camera settings. Lens The 8-48 mm zoom lens is fitted with a close-up diopter and step-up ring.
VisiDoc-It Imaging System 5 Transilluminator For VisiDoc-It systems, transilluminators are optional equipment. The VisiDoc-It System can accommodate UVP’s Benchtop and FirstLight transilluminator models. The VisiDoc-It (with stand design) can also accommodate the High Performance UV Transilluminators (25-watt) and White/UV Transilluminators (8-watt).
VisiDoc-It Imaging System 6 Setup Instructions Components Camera with zoom lens, bracket, filter, cables VisiDoc-It hood or stand USB storage device, 8GB (minimum) Transilluminator (may be ordered separately) WARNING: DO NOT ATTEMPT TO CONNECT ANY WIRING WHILE THE EQUIPMENT IS CONNECTED TO ANY POWER SUPPLY CAUTION: Do not install the system in places with high moisture, dust, or high temperatures. Do not use any oil or petroleum based cleaner for the cabinet.
VisiDoc-It Imaging System Insert and tighten the knob/washer in the central hole in the camera to secure the camera to the bracket. Plug the camera cable into the top the camera and the other end into a USB port on back of the processor. Connect the power cord from the transilluminator to a surge protected power outlet. Connect the main power cord from the back of the processor to a surge protected power outlet.
VisiDoc-It Imaging System 8 Using the System Powering Up the System Power up the system by pushing once on the MAIN POWER button located on the right side of the processor. Turn on the transilluminator. To power down the system, push the main power button. Main power Adjusting the Screen Angle To adjust the angle of the screen, loosen the knobs on each side of the monitor. Twist each knob counter-clockwise. Tilt the screen to the desired angle. Turn each knob clockwise to tighten.
VisiDoc-It Imaging System 9 To shut down the TS software, touch the X on the bottom left corner of the screen. To turn the system off, press the MAIN POWER button or power down from the Windows icon on the bottom right corner of the screen. Refer to Touch Screen Interface in this manual for detailed instructions on using the software. Using the Transilluminator To use the transilluminator, turn on the transilluminator power on the front of the unit.
VisiDoc-It Imaging System 10 Touch Screen Interface Setting User Preferences on the TS Software Before capturing images, set up the user preferences by touching the PREF (preferences) button on the main screen. Select from the following tabs: Capture Postprocessing Saving Capture Tab Active Camera: The name of the attached camera will be shown. Bit Depth: Select the bit depth. 16 bpp (bits per pixel) is shown for the Gel HR Camera. Display Time Stamp: Turn the time stamp on or off.
VisiDoc-It Imaging System 11 Saving Tab NOTE: If the auto save function is enabled, the image will automatically save when the SNAP button is pressed. If the auto save function is not enabled, press the SAVE button to save an image. A pop up screen will allow the user to save to the USB Drive or a different location with Prompt for Location function. Save Images To: Select the location where images are to be saved. White highlight indicates which button is activated.
VisiDoc-It Imaging System 12 Identifying the Touch Screen Functions and Tools Using the software touch screen allows convenient selection of image capture, save, print and other functions of the system. Callouts are provided below to briefly describe the buttons.
VisiDoc-It Imaging System 13 5. To snap (capture) the image, touch the SNAP button. NOTE: When using the SNAP button, if the Auto Save function is enabled, the image will automatically be saved. 6. Touch the SAVE button to save the image to the location specified in the Preferences. The file name is assigned automatically by the software as UVP#####mmddyyyy.* NOTE: Once an image is saved, the user cannot open the image with the software.
VisiDoc-It Imaging System 14 Connecting to a Network Network Connectivity The TS System has built-in networkability. While it is fairly simple to connect the device to the network, it is highly recommend to obtain assistance from your network administrator. Follow the Microsoft or local standard network protocols for network configuration. To exit the TS software interface and go to Microsoft Windows, touch the WINDOWS ICON located at the bottom right corner of the main screen.
VisiDoc-It Imaging System 15 Service Procedures Return Procedure A Returned Goods Authorization (RGA) number must be obtained from UVP Customer Service before returning any product. Replacement Parts and Accessories To order accessories or replacement parts for the VisiDoc-It System, contact UVP’s offices.
VisiDoc-It Imaging System 16 Error Messages Pop Up on the Screen Messages appear on the screen that might be related to the TS software interface, or Microsoft Windows. If the message is related to Microsoft Windows, such as a reminder to activate or update your copy of Windows, please contact your system administrator for assistance.
