www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 OOri quick start guide v1.3a OORI Congratulations on your purchase of OORI! The following quick start guide will show you how to get OORI in the air for the first time, and how to enjoy the fantastic experience of flight! OORI BOX CONTENTS 1 x OOri drone (Inc.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 TABLE OF CONTENTS OUT OF THE BOX ..................................................................................................................................................................... 3 Antenna installation ........................................................................................................................................................ 3 CAMERA ANGLE .............................................
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 OUT OF THE BOX Antenna installation The radio requires the 2 antennas to be installed before operation. They are included in the box and can be screwed onto the top of the radio. Order is not important, screw both down until tight.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 CAMERA ANGLE Making adjustments OORI has two camera angle settings. For initial flights, it should be looking straight out of the front (zero degree angle). If your camera angle isn't straight, set it to zero degrees by clicking it into place. Once you have gained confidence and flying faster, you can increase the camera angle.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 CHARGING Changing the OORI battery The OORI battery slides in and out from the bottom of the drone. Simply slide the battery in like the pictures below, until the battery tab clicks into place. For removal, lift the tab partially and pull backwards.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 CHARGING USB cable charging Charging OORI is simple. With a battery onboard, plug in a micro USB. OORI can charge from a laptop USB port, but will charge fastest from a wall wart style plug. The ring on top of OORI will show the charge on the battery, complete once the entire ring is green.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 POWERING Checking the Battery level A single click of the main OORI button will show the current battery level. For example, a fully charged battery is a full green ring. A partially charged battery is an orange partially lit ring. This is also true for the radio. A single click of the power button will show the charge status.
www.uvify.com Get help at Support.uvify.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 POWERING Powering FPV transmitter In normal operation, the radio should be powered first. This is done by a short click of the power button followed by holding the button until the LED is fully lit. A small delay between clicking and holding may be necessary, as this helps prevent accidental powering of the radio.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 POWERING Powering OORI Click the main OORI button so the LED ring lights up, then hold the button until the green ring is complete. Upon release, the LED will show rainbow colors. The OORI is now powered. Note: if the main button is held too long it will go into bind mode, as described below. This is not required for normal operation, turn off OORI and power up again for normal flying.
www.uvify.com Get help at Support.uvify.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 LED SETUP Changing the LED colors The color of OORI and the radio can be changed by holding the right front button on the radio. When released, the OORI and radio will hold this color. It can be changed at any time.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 BINDING Prepare OOri for binding In some instances, it may be required to link OORI with a radio (out of the box this is not required). Click and then hold the main button on OORI until the yellow ring is completely full, then release. The yellow ring will spin showing OORI is ready for link.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 BINDING Prepare FPV Transmitter for binding Once OORI is in bind mode as above, power on the radio by holding the left front button while clicking and then holding the power button. The colors will sync on OORI and the transmitter once link is established. You will be able to see the FPV feed on the screen.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 VIDEO STREAM Switching video channel When OORI and the transmitter are powered and bound, it is possible to switch between video channels by clicking the "BIND/CH" button. This will cycle both the transmitter and OORI through 8 available channels in the F band. You should switch channels when flying with others and two or more people are on the same channel.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 ARMING Throttle position Lower the throttle stick to the bottom, OORI will not arm without this for safety reasons. Hold this stick down and then click the arm switch as below. ARMING Arm switch The arm switch starts and stops the props on OORI. To start the props, put the throttle stick at the bottom and then short click the arm button, which is in the left trigger position.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 FLYING Stick Layout The default stick layour for the OORI transmitter is Mode 2. The sticks control OORI as laid out below.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 FLYING Optical position hold In flight, OORI has the capability to hold its position with several sensors. Optimal conditions for position hold to work are indoors in a well lit area. Areas with bright sunlight or shiny floors are not optimal for position hold capabilities. Once you lift off OORI, optimal height is around waist to shoulder level during flight, but can go higher or lower depending on where you're flying.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 FLYING Altitude hold If conditions aren't good for position hold, OORI will switch to altitude hold mode. In altitude hold, OORI can drift without correcting itself, so the pilot should use the sticks to ensure OORI doesn't go in unwanted directions. Altitude hold mode will display as "ATTI" in the top left of the video feed, and will change back to "OPTI" automatically once conditions are good again.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 LANDING Disarming Clicking the arm switch while the props are spinning will disarm OORI, causing the props to stop. At the end of our flight, bring OORI to touching the ground and then click the arm / left trigger switch to stop the props from spinning and disarm OORI.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 POWER OFF Powering off OORI Short click of the main OORI button followed by holding the main button will power down OORI. Once off, all LEDs on OORI will be off. POWER OFF Powering off FPV transmitter Short click of the radio power button followed by holding the button will power down the radio. Once powered down, the LEDs and screen will be off.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 PROP REPLACEMENT Prop direction and install If a prop is damaged or bent, it should be replaced before flight or else OORI may not perform optimally, and you could incur damage to the power system if the damage is significant. To replace a prop, undo the 2 bolts from the top of the prop with the included hex wrench. Remove the prop from the motor and replace it with an identical prop.
www.uvify.com Get help at Support.uvify.
www.uvify.com Get help at Support.uvify.
www.uvify.com Get help at Support.uvify.com Talk to us: +1 (628) 888-6336 PROP GUARD Prop guard removal Use the included 1.5mm hex wrench to loosen the 8 bolts out of the bottom of the prop guards. Once loose, the prop guards will come off. CAUTION! DO NOT USE THE BOLTS FROM THE PROP GUARDS TO RE-SECURE THE MOTORS AFTER PROP GUARD REMOVAL IF THESE BOLTS ARE USED THEN YOU MAY DAMAGE THE MOTORS.
www.uvify.com Get help at Support.uvify.
www.uvify.com Get help at Support.uvify.
