Installation Sheet

UTTERMOST
MANUFACTURERS OF WALL DECOR, LIGHTING,
DECORATIVE ACCESSORIES AND ACCENT FURNITURE
PO BOX 558/3325 GRASSY HILL RD. ROCKY MOUNT, VIRGINIA 24151
www.uttermost.com
FIG. 1
FIG. 2
ASSEMBLY AND INSTALLATION
1. Take the parts out of the mounting package.
Srew (3) the CIRCULAR MOUNTING BRACKET (2) to each end of OUTLET BOX (1).
4.
2.
Pull the SUPPLY WIRES (6&8) and the SUPPLY GROUND WIRE (5) out from the OUTLET BOX
(1). Attach the CIRCULAR MOUNTING BRACKET (2) assembly to the OUTLET BOX (1). (See Fig.1).
3.
Put the FIXTURE SCREW (12) and HEX NUT (11) into the hole of the CIRCULAR MOUNTING
BRACKET (2). Place the CANOPY (16) over the OUTLET BOX (1) and adjust the FIXTURE SCREW
(12) and HEX NUT (11) together with the mounting bracket until properly aligned with the CANOPY (16).
5.
Unravel the FIXTURE LEAD WIRE (7 & 9) and FIXTURE GROUND WIRE (4). Connect the power
supply wires with the fixture lead wires using WIRE CONNECTORS (10). Loop the FIXTURE GROUND
WIRE (4) around the ground screw of the MOUNTING BRACKET (2). Note: Be sure to provide extra 3”
length of the GROUND WIRE (4). Connect the remaining FIXTURE GROUND WIRE (4) to the SUPPLY
GROUND WIRE (5) using WIRE CONNECTOR (10).Place wiring and connections in the outlet box (1).
6.
ASSEMBLY & INSTALLATION
INSTRUCTIONS FOR #21530
Please read carefully and save these instructions, as you may need them at a later date.
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If
you are unfamiliar with proper electrical wiring connections obtain the services of a qu
alified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by
referencing the illustrations on the installation instructions.
CAUTION
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
Install the HANGING RODS (14) to the FIXTURE BODY (13). Adjust the length of wire needed for the
installation and remove the excess.Determine the number of rods to be assembled in accordance with the
hanging height. Pull supply and ground wire through the selected rods. Tighten and connect the top end
of the RODS (15)to the canopy.
7.
8.
9.
Hang the SAFETY CABLE (17) on the MOUNTING BRACKET (2).Adjust the CANOPY (16) and screw
the two DECORATIVE NUTS (18) onto the FIXTURE SCREW (12) with HEX NUT (11) to fix in place
(See Fig.1).
Screw light bulbs into the lamp sockets (19) and make sure they do not exceed the maximum wattage specified
on the fixture’s wattage rating capacity. MAXIMUM 60W.
INSTALLATION IS NOW COMPLETED.
CANOPY
CANOPY
SAFETY CABLE
DECORATIVE NUT
DECORATIVE NUT
HANGING ROD(12inch)
FIXTURE FRAME/BODY
BLUB
HANGING ROD(6inch)
LAMP SOCKET
HEX NUT
WIRE CONNECTOR
SMOOTH FIXTURE LEAD WIRE
BLACK SUPPLY WIRE (not included)
RIBBED FIXTURE LEAD WIRE
WHITE SUPPLY WIRE (not included)
SUPPLY GROUND WIRE (not included)
FIXTURE GROUND WIRE
OUTLET BOX SCREW
CIRCULAR MOUNTING BRACKET
OUTLET BOX (NOT INCLUDED)
FIXTURE SCREW
(18)
(16)
(17)
(12)
(2)
(9)
(8)
(5)
(4)
(11)
(3)
(1)
(6)
(7)
(10)
(13)
(20)
(19)
(18)
(15)
(14)
(16)
Carefully unpack all lamp parts from the carton.