Installation Sheet

ManualsBrandsUttermost ManualsLightingQuadrangle 13" Wide Urban Industrial 2 Light Cage Style Single Pendant with Taper Candle Lights by Kalizma Home

UTTERMOST

MANUFACTURERS OF WALL DECOR, LIGHTING,

DECORATIVE ACCESSORIES AND ACCENT FURNITURE

PO BOX 558/3325 GRASSY HILL RD. ROCKY MOUNT, VIRGINIA 24151

www.uttermost.com

FIG. 1

FIG. 2

ASSEMBLY AND INSTALLATION

1. Take the parts out of the mounting package. Insert the

OUTLET SCREW

(3) into mounting bracket

slots and screw to the OUTLET BOX (1). Pull the SUPPLY WIRES (6&8) and the SUPPLY GROUND

WIRE (5) out from the OUTLET BOX (1) and attach the mounting bracket assembly to the OUTLET

BOX (1). (See Fig.1).

Insert the FIXTURE SCREW and HEX NUT (12) into the slots of the MOUNTING BRACKET (2).

Place the CANOPY (16) over the OUTLET BOX (1) and adjust until the canopy is aligned and

centered.

Unravel the FIXTURE LEAD WIRES (7&9) and FIXTURE GROUND WIRE (4). Attach the power

supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (8) to the SMOOTH

FIXTURE LEAD WIRE (9). WHITE SUPPLY WIRE (6) to the RIBBED FIXTURE LEAD WIRE

(7) and Loop the FIXTURE GROUND WIRE (4) around the GROUND SCREW (11) of the MOUNTING

BRACKET (2). (Note: Be sure to provide extra 3” length of the FIXTURE GROUND WIRE (4).

Connect the remaining FIXTURE GROUND WIRE (4) to the SUPPLY GROUND WIRE (5) using

WIRE CONNECTOR (10). Place wires and connections in the OUTLET BOX (1). (See Fig.1).

ASSEMBLY & INSTALLATION

INSTRUCTIONS FOR #21529

Please read carefully and save these instructions, as you may need them at a later date.

GENERAL

All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If

you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.

Remove the fixture and the mounting package from the box and make sure that no parts are missing by

referencing the illustrations on the installation instructions.

CAUTION

Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.

Insert the hanging rods to the center fixture cage and tighten. Adjust the length of wire needed for your

installation and remove excess. Determine number of HANGING RODS (14) to be assembled to the

fixture body in relation to the hanging height. Pull supply wire with Ground wire through the selected

rods. Joined together and tighten the RODS (14). Connect the top end of the ROD (15) to the center

CANOPY (16). (See Fig.2).

Attach the FIXTURE BODY (13) through its canopy by locking the Fixture SCREW and HEX NUT

(12) with two DECORATIVE NUTS (17). (See Fig.1).

Screw the light bulbs into the lamp sockets (18) and make sure they do not exceed the maximum

wattage specified on the fixture’ wattage rating capacity. MAXIMUM 60W.

INSTALLATION IS NOW COMPLETED.

Carefully unpack all lamp parts from the carton.

HANGING RODS(6inch)

CANOPY

DECORATIVE NUT

FIXTURE FRAME/BODY

HANGING RODS(12inch)

LAMP SOCKET

GROUND SCREW

WIRE CONNECTOR

SMOOTH FIXTURE LEAD WIRE

BLACK SUPPLY WIRE (not included or house supply)

RIBBED FIXTURE LEAD WIRE

WHITE SUPPLY WIRE (not included or house supply)

SUPPLY GROUND WIRE (not included)

FIXTURE GROUND WIRE

OUTLET BOX SCREW

MOUNTING BRACKET

OUTLET BOX (NOT INCLUDED)

FIXTURE SCREW and HEX NUT

(11)

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(12)

(16)

(17)

(16)

(17)

(15)

(14)

(13)

(18)