Platform Product Name WA3003G4 Release 1.0 Guide Type Release 1.0 Doc.
Copyright © 2006 UTStarcom, Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without prior, express and written permission from UTStarcom, Inc. UTStarcom, Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of UTStarcom, Inc. to provide notification of such revision or changes.
1 Overview............................................................................................................... 3 Introduction...................................................................................................................... 3 2 WA3003G4 Installation ....................................................................................... 5 3 Configuration ....................................................................................................... 9 3.1 Setup.....
2 Overview - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
1 1 Overview This chapter provides an overview of the UTStarcom WA3003G4 VDSL 2 Modem and describes its Features and System Requirements. This chapter contains the following topics: · Introduction · Features · System Requirements Introduction Congratulations on becoming the owner of the WA3003G4. Your LAN (local area network) will now be able to access the Internet using your high-speed VDSL connection. This User Guide will show you how to install and set up your WA3003G4.
2 2 WA3003G4 Installation In addition to this document, your WA3003G4 should arrive with the following: · One WA3003G4 · One power adapter and power cord · One cross-over/straight Ethernet cable · One RJ-11 to RJ-11 telephone Cable · One splitter or low-pass filter Front Panel The front panel contains 7 LEDs indicating the status of WA3003G4 showing as Figure 2.1: Figure 2.1 WA3003G4 Front Panel.
6 Chapter 2 WA3003G4 Installation Table 2.1 Illustration of WA3003G4 Front Panel Rear Panel The rear panel contains the ports for WA3003G4 data and power connections showing as Figure 2.2 Figure 2.2 WA3003G4 Back Panel. Label Function Antenna For WiFi functionality.
Chapter 2 WA3003G4 Installation WARNING Before you begin, turn the power off for all devices. These include your computer(s), your LAN hub/switch (if applicable), and the WA3003G4. Figure 2.3 illustrates the hardware connections. The layout of the ports on your device may vary from the layout shown. Refer to the steps that follow for specific instructions. Figure 2.3. Overview of Hardware Connections Step 1. Connect the VDSL cable and optional telephone.
8 Chapter 2 WA3003G4 Installation You can attach a telephone line to the device. This is helpful when the VDSL line uses the only convenient wall phone jack. If desired, connect the telephone cable to the port labeled PHONE. WARNING Although you use the same type of cable, The VDSL and PHONE ports are not interchangeable. Do not route the VDSL connection through the PHONE port. Step 2. Connect the Ethernet cable.
3 3 Configuration 3.1 Setup l l l Step 1: Connect WA3003G4 and PC with an Ethernet cable. Step 2: Power on the WA3003G4. Step 3: The default IP of the WA3003G4 is 192.168.1.1. 3.2 Establish the Connection Enter the IP address (default is 192.168.1.1) of WA3003G4 from the Web Browser. A Dialogue Box will be popped up to request the user to login. (Figure 3.2.1) Figure 3.2.1.
Figure 3.2.2. WA3003G4 Device Info 3.3 Device Info The system administrator can configure WA3003G4 remotely or locally via a Web Browser. Network configuration must be planned and decided before starting the configuration procedure. Under “Device Info” selection, based on different information characteristics, they are grouped into following categories: Summary WAN Statistics Route ARP DHCP 3.3.1 Summary Click on “Summary” in the left frame, Figure 3.3.
Figure 3.3.1. WA3003G4 Device Info – Summary Figure 3.3.1 reflects two different category information of WA3003G4 as following: Device Info Board ID, Software Version, Bootloader (CFE) Version, Firmware Version, Hardware Version, Model Name, VDSL Software Version and Wireless Driver Version. Status of DSL connection B0 Traffic Type: B0 Line Rate, Upstream and Downstream. B1 Traffic Type: B0 Line Rate, Upstream and Downstream.
3.3.2 Device Info -- WAN Figure 3.3.2. Device Info – WAN Figure 3.3.2 displays the WAN status of WA3003G4 3.3.
3.3.3.1. Device Info Statistics -- LAN Figure 3.3.3.1. Device Info Statistics – LAN Check to Enable/Disable IGMP Multicast and WAN Service. Click on “Next” to go to next step.
3.3.3.2 Device Info Statistics -- WAN 3.3.3.
3.3.3.3 Device Info Statistics -- ATM Figure 3.3.3.3 Device Info Statistics -- ATM Enable the WiFi function here and configure the SSID for the WiFi interface.
3.3.3.4 Device Info Statistics -- ADSL Figure 3.3.3.
3.3.3.5 Device Info Statistics -- VDSL Figure 3.3.3.
3.3.4 Device Info Route Figure 3.3.
3.3.5 Device Info ARP Figure 3.3.5 Device Info ARP .
3.3.6 Device Info DHCP Figure 3.3.6 Device Info DHCP 3.
3.4.1 Advanced Setup -- WAN Figure 3.4.1 Advanced Setup – Wide Area Network (WAN) Setup This page shows the current existing WAN interfaces in the system. User can choose Add, Edit, or Remove to configure WAN interfaces. 3.4.1.1 Advanced Setup – add WAN Interface To add a WAN interface, click “Add”, Figure 3.4.1.
Figure 3.4.1.1 Advanced Setup – ATM PVC Configuration Give proper PORT, VPI/VCI values; for detail information, please consult with your ISP. provider. Enable the QoS function for this PVC here. Use “Advanced Setup/Quality of Service” to assign priorities for the application. To configure VLAN, please check “VLAN Mux – Enable Multiple Protocols Over a Single PVC”, and Figure 3.4.1.1.
Figure 3.4.1.1.a Advanced Setup –VLAN Configuration Input proper VLAN ID and click on “Next” to go to next step. Three different connection types show as below.
3.4.1.1.1 PPP over Ethernet Connection Figure 3.4.1.1.1.a Advanced Setup – PPPoE Connection Type To establish a PPPoE connection, select “PPP over Ethernet (PPPoE)” and “Encapsulation Mode” click “Next” for next step.
Figure 3.4.1.1.1.b Advanced Setup – PPP Username and Password Give “PPP Username”, “PPP Password”, “PPPoE Service Name” and select “Authentication Method” (AUTO/PAP/CHAP). Please consult with your ISP provider for detail information. The “Dial on Demand” function, if checked, will tear down the PPP link automatically if there is no outgoing packet for the programmed period of time, WA3003-G4 will display a box for input “Inactivity Timeout” as showing in Figure 3.4.1.1.
Figure 3.4.1.1.1.
Figure 3.4.1.1.1.d Advanced Setup – Enable IGMP Multicast, and WAN Service. Check “Enable/Disable IGMP Multicast” and “WAN Service”. Click on “Next” to go to next step.
Figure 3.4.1.1.1.e Advanced Setup – WAN Setup – Summary Figure 3.4.1.1.1.e gives a summary of previous steps (PPPoE). Make sure that the configurations match the settings provided by your ISP provider, and then click on “Save” button to complete the configuration procedure displays all the settings in previous steps. Click “Back” if you need to revise previous settings 3.4.1.1.
Figure 3.4.1.1.2.a Advanced Setup –MER Connection Type Select “MAC Encapsulation Routing (MER)”, and the “Encapsulation Mode”. Please consult with your ISP provider for detail information. Click on “Next” to go to next step. .
Figure 3.4.1.1.2.b Advanced Setup –Connection Type MER WAN IP Settings WAN IP/Subnet Mask, Default Gateway, and DNS Server can either be obtained automatically or set manually. The WAN IP can be either fixed (assigned by your ISP provider) or dynamic (via DHCP Client). Enter the “Vendor ID” if DHCP Client is selected and your ISP requests for it. Click on “Next” for next step.
Figure 3.4.1.1.2.c Advanced Setup –MER- NAT, Firewall, IGMP Multicast and WAN service Check to Enable/Disable NAT, Fullcone NAT and Firewall functions. Use “Advanced Setup -- Security” to assign filter rules. Check to Enable/Disable IGMP Multicast and WAN Service. Click on “Next” to go to next step.
Figure 3.4.1.1.2.d Advanced Setup WAN Setup – Summary Figure 3.4.1.1.2.d gives a summary of previous steps (MER). Make sure that the configurations match the settings provided by your ISP provider, and then click on “Save” button to complete the configuration procedure displays all the settings in previous steps. Click “Back” if you need to revise previous settings 3.4.1.1.3 Bridging Connection Select “Bridging”, and the “Encapsulation Mode”. Please contact you ISP for the information.
Figure 3.4.1.1.3.
Figure 3.4.1.1.3.b Advanced Setup –Bridging Type – WAN Service Figure 3.4.1.1.3.cAdvanced Setup WAN Setup – Summary Figure 3.4.1.1.3.c gives a summary of previous steps (Bridging). Make sure that the configurations match the settings provided by your ISP provider, and then click on “Save” button to complete the configuration procedure displays all the settings in previous steps. Click “Back” if you need to revise previous settings 3.4.
Figure 3.4.2 Advanced Setup – LAN Give IP (LAN IP) and Subnet Mask to the device. Select to Disable/Enable DHCP Server and configure related settings for that mode. If necessary, check the “Secondary IP” to configure the secondary IP address and Subnet Mask for LAN. This IP address is used for management only. Note that Network Address Translation function (NAT) is default enabled and is not showing on the page to prevent it from being disabled. Click on “Next” to go to next step. 3.4.
Figure 3.4.3.1.
Figure 3.4.3.1 b Advanced Setup – NAT – Virtual Servers Select the service name, and enter the server IP address and click "Save/Apply" to forward IP packets for this service to the specified server. NOTE: The "Internal Port End" cannot be changed. It is the same as "External Port End" normally and will be the same as the "Internal Port Start" or "External Port End" if either one is modified. Remaining number of entries that can be configured: 32 1.
Figure 3.4.3.2.
Figure 3.4.3.2.b Advanced Setup – NAT – Port Triggering Some applications such as games, video conferencing, remote access applications and others require that specific ports in the Router's firewall be opened for access by the applications. You can configure the port settings from this screen by selecting an existing application or creating your own (Custom application) and click "Save/Apply" to add it. Remaining number of entries that can be configured: 32 2.
Figure 3.4.3.4 Advanced Setup – NAT— ALG 3.4.4 Advanced Setup – Security 3.4.4.1 Advanced Setup – Security – IP Filter 3.4.4.1.1 Advanced Setup – Security – IP Filter -- Outgoing By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be BLOCKED by setting up filters.
Figure 3.4.4.1.1.a Advanced Setup – Security – IP Filter -- Outgoing WA3003G4 allows the users to create a filter rule to identify outgoing IP traffic by specifying a new filter name and at least one condition. All of the specified conditions in this filter rule must be satisfied for the rule to take effect.
3.4.4.1.1.b Advanced Setup – Security – IP Filter—Add Outgoing Rules 3.4.4.1.2 Advanced Setup – Security – IP Filter – Incoming By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled.
Figure 3.4.4.1.2.a Advanced Setup – Security –IP Filter – Incoming WA3003G4 allows the users to create a filter rule to identify incoming IP traffic by specifying a new filter name and at least one condition. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. When there are multiple WAN interfaces configured, users can choose which interface(s) will apply the rule.
Figure 3.4.4.1.2.b Advanced Setup – Security –IP Filter – Add Incoming Rules 3.4.4.2 Advanced Setup – Security – MAC Filter MAC Filtering is only effective on ATM PVCs configured in Bridge mode. “FORWARDED” means that all MAC layer frames will be FORWARDED for those matching with any of the specified rules in Figure 3.4.4.2.a MAC Filter Rules. “BLOCKED” means that all MAC layer frames will be BLOCKED for those matching with any of the specified rules in Figure 3.4.4.2.
Figure 3.4.4.2.
Click “Add” to add a MAC Filter Rule as shows in Figure 3.4.4.2.b Advanced Setup – Security – Add MAC Filter Figure 3.4.4.2.b Advanced Setup – Security – Add MAC Filter To clean all MAC Filter Rules, click “Change Policy” in Figure 3.4.4.2.a Advanced Setup – Security – MAC Filter.
Figure 3.4.4.2.c Advanced Setup – Security – Clean MAC Filter Rules 3.4.4.
Figure 3.4.4.3.a Advanced Setup – Security – Parental Control Click “Add” to set restriction rules as following: Figure 3.4.4.3.b Advanced Setup – Security – Parental Control – Add Restrictions 3.4.5 Advanced Setup – Quality of Service 3.4.6 Advanced Setup – Routing WA3003G4 provides three different routing types as below: 3.4.6.
Figure 3.4.6.1 Advanced Setup – Routing – Default Gateway 3.4.6.
Figure 3.4.6.2.a Advanced Setup – Routing –Static Route Click on “Add” to create a new Static Route. Enter the destination network address, subnet mask, gateway AND/OR available WAN interface then click "Save/Apply" to add the entry to the routing table as showing in Figure 3.4.6.2.
Figure 3.4.6.2.a Advanced Setup – Routing –Static Route 3.4.6.
Figure 3.4.6.3 Advanced Setup – Routing –RIP To activate RIP for the device, select the 'Enabled' radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the 'Enabled' checkbox for the interface. Click the 'Save/Apply' button to save the configuration, and to start or stop RIP based on the Global RIP mode selected. 3.4.7 Advanced Setup – DNS 3.4.7.1 Advanced Setup – DNS – DNS Server Figure 3.4.7.
Figure 3.4.7.2.a Advanced Setup –DNS –Dynamic DNS This page allows you to add a Dynamic DNS address from DynDNS.org or TZO. Figure 3.4.7.2.
3.4.8 Advanced Setup – DSL Under DLS settings, a lot of DSL modulations can be set including: G.DMT, G.lite. T1.413 ADSL2, Annex L, M and ADSL2+; also the phone line pair and capability showing as Figure 3.4.8.1 Advanced Setup – DSL Settings. Figure 3.4.8.1 Advanced Setup – DSL Settings Click “Advanced Settings”, Figure 3.4.8.
Figure 3.4.8.2 Advanced Setup – DSL Advanced Settings A capable of test modes including: Normal, Reverb, Medley, No retrain and L3 are available for choice. Click “Tone Selection”, Figure 3.4.8.3 Advanced Setup – DSL -- ADSL Tone Settings shows as below: Before any changes of these settings, please make sure you do understand the actual meaning of each setting; otherwise, please leave as it. For detail information, please consult with your ISP provider. Figure 3.4.8.
3.4.9 Advanced Setup – Print Server You are able to set up the print server through this page, enable “Enable on-board print server” checkbox, and input “Printer name” and “Make and model”; click “Save/Apply” as showing on Figure 3.4.9 Advanced Setup – Print Server. Figure 3.4.9 Advanced Setup – Print Server 3.4.10 Advanced Setup – Port Mapping Port Mapping supports multiple ports to PVC and bridging groups. Each group will perform as an independent network.
Figure 3.4.10.a Advanced Setup – Port Mapping Port Mapping Configuration To create a new mapping group: 1. Enter the Group name and select interfaces from the available interface list and add it to the grouped interface list using the arrow buttons to create the required mapping of the ports. The group name must be unique. 2. If you like to automatically add LAN clients to a PVC in the new group add the DHCP vendor ID string.
Figure 3.4.10.b Advanced Setup – Port Mapping Configuration. 3.4.
Figure 3.4.11 Advanced Setup – IPsec 3.4.12 Advanced Setup – Certificate 3.4.12.1 Advanced Setup – Certificate – Local Certificates Add, View or Remove certificates through this page. Local certificates are used by peers to verify your identity. Maximum 4 certificates can be stored. .Figure 3.4.12.1.a Advanced Setup – Certificate – Local Certificates Click “Create Certificate Request” button on Figure 3.4.12.1.a Advanced Setup – Certificate – Local Certificates and Figure 3.4.12.1.
3.4.12.1.b Advanced Setup – Certificate – Create new certificate request Enter appropriate data and click “Apply” button, Figure 3.4.12.1.
Figure 3.4.12.1.c Advanced Setup – Certificate – Local Certificates – Certificate signing request shows Certificate signing request successfully created. Note a request is not yet functional - have it signed by a Certificate Authority and load the signed certificate to this device Click “Import Certificate” button on Figure 3.4.12.1.a Advanced Setup – Certificate – Local Certificates and Figure 3.4.12.1.d Advanced Setup – Certificate – Local Certificates – Import certificate shows up Figure 3.4.12.1.
3.4.12.2 .a Advanced Setup – Certificate – Trusted CA Click “Import Certificate” button, 3.4.12.2.b Advanced Setup – Certificate – Trusted CA – Import CA Certificate shows up; click “Apply” when finish the input.
3.5 Wireless Use the Wireless screen to configure WA3003-G4 for wireless access. Six parts are list as following: Basic Security MAC Filter Wireless Bridge Advanced Station Info 3.5.1 Basic This page allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements.
Figure 3.5.2 Wireless -- Security 3.5.3 MAC Filter This page allows users to Add/Remove hosts with the specified MAC addresses that are able or unable to access the wireless network. When users decide to use Allow, only the MAC addressed in the user defined list can access the wireless network. When users use Deny, only the user specified MAC addresses are unable to access to wireless network. Note: The MAC addresses in the list would immediately take effect when Allow or Deny is checked.
3.5.4 Wireless Bridge 3.5.5 Advanced 3.5.6 Station Info 3.6 Diagnostics 3.
