Use & Care Guide

OPERATING INSTRUCTIONS
OUTDOOR TIMER
ITEM #0155550
MODEL #UTTNO2411
L
ights do not turn
on as
programmed.
Lights come on
in “AM” but are
supposed to
come on in “PM.”
Lights come on
in “PM” but are
supposed to
come on in “AM.”
Lights come on
before the actual
time.
Connected lights are
not in “ON” position;
t
hey are not
f
unctioning; timer is
not receiving power,
o
r “BYPASS SWITCH”
i
s in the “OUTLET ON”
position.
Pins were pushed
down in the “AM”
section (highlighted in
white on the timer dial).
Pins were pushed
down in the “PM”
section (highlighted in
black on the timer dial).
“CURRENT TIME” was
not set properly.
Ensure the connected
lights are functional by
p
lugging them directly
i
nto the outlet. Be sure
the connected lights are
i
n the “ON” position if
t
hey have their own
switch. Make sure the
outlet the timer is
plugged into is active.
Check that the “BYPASS
SWITCH” is in the
“TIMER ON” position.
Be sure the pins are
pushed down in the “PM”
section (highlighted in
black on the timer dial).
Be sure the pins are
pushed down in the “AM”
section (highlighted in
white on the timer dial).
Refer to step 2 of this
manual. Be sure
“CURRENT TIME” is set
in the white section on
the timer dial if the
“CURRENT TIME” is in
the “AM.” The
“CURRENT TIME”
should be set in the black
section on the timer dial
if the “CURRENT TIME”
is in the “PM.”
TROUBLESHOOTING
Printed in China
4
. Set the “CURRENT TIME”
Rotate the entire gray push-pin
dial clockwise until the arrow
marked “CURRENT TIME” aligns
with the current time of day on the
dial. “AM” hours are highlighted in
WHITE. “PM” hours are
highlighted in BLACK.
5. Set “BYPASS SWITCH”
When the switch is in the “TIMER
ON” position, timer will
automatically turn the attached
device on and off. When the
switch is in the “OUTLET ON”
position, timer will bypass the
programming and the attached
device will remain on.
6. Attach up to TWO DEVICES
to the timer
Plug the devices into the outlets
on the bottom of the timer.
HELPFUL TIPS
• This timer repeats the same settings daily.
• To push down or pull up the gray pins, use your finger
or the tip of a small non-metalic insulated tool, such as
a toothpick (not included).
• Set up to 48 different “ON” and “OFF” times in a 24
hour period by the positioning of the gray pins. Pins
pressed down represent the ‘ON’ time. Pins in the up
position represent ‘OFF’ time.
• Switching the timer to “OUTLET ON” will bypass
programming, however, the timer dial will continue to
rotate and maintain the current time.
• This timer is weather-resistant and rated for outdoor
use. The timer will function outdoors when installed
and operated as outlined in this manual.
• The “Power” indicator will glow red when the timer
programming is activated and power is being provided
to attached devices.
IN CASE OF POWER FAILURE
Timer will stop operating if the power goes out. Once
power is restored, reset the time of day as explained in
Step 4 of the instructions.
SAFETY INFORMATION & SPECIFICATIONS
THIS TIMER IS A “GROUNDED” DEVICE.
The male plug contains a ground pin and is only intended
for use with a three-pronged grounded outlet.
DO NOT ATTACH A DEVICE THAT EXCEEDS THE
UNIT RATINGS:
125 V AC / 60 Hz
15 A / 1,875 W Resistive (General Purpose)
10 A / 1,250 W Tungsten (Incandescent)
1/2 HP (Horsepower Motor)
LIMITED 1 YEAR WARRANTY
Prime warrants this product to be free from manufacturing defects for
a period of one year from the original date of purchase (“warranty
period”). This warranty is limited to the repair or replacement of this
product only and Prime is not liable for any consequential or
incidental damage to other products that may be used with this unit.
This warranty is effective only if such unit is returned to Prime not
later than thirty (30) days after the expiration of the warranty period.
Warranty is void if damage is due to neglect, misuse, alteration,
modification, improper installation, or repair by other than Prime.
This warranty is in lieu of all other warranties express or implied.
Some states do not allow limitations on how long an implied warranty
lasts or permit the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to
you.
It is our experience that a product that fails prematurely due to a
manufacturing defect in materials or workmanship, will generally do
so very early in the product’s life cycle, often the first or second time
the product is used. Products that are returned for warranty
inspection after months or years of continuous reliable service are
usually the result of normal wear and tear, which is not considered a
defect in materials or workmanship and therefore is not covered by
the warranty.
This warranty gives you specific rights, and you may also have other
rights which vary from state to state. If unit should prove defective
within the warranty period, return within the time period set forth
above prepaid with the original purchase receipt to:
Prime Wire & Cable, Inc.
ATTN: Timer Warranty
280 Machlin Court
City of Industry, CA 91789
1. INSTALL TIMER to a vertical
flat surface close to a
properly installed outdoor-
rated grounded receptacle
a. Using a screw or hook (not
included), secure the
MOUNTING TAB at the top of
the timer to a wall or post.
b. For a more secure mounting,
use the two MOUNTING
HOLES on the back of the timer.
• Create a mounting template
by placing a sheet of paper
over the back of the timer and
punching holes through the
paper where the mounting
holes are located on the timer.
• Temporarily secure the mounting template to the flat
surface where the timer is to be mounted.
• Drill two 3/32 inch pilot holes where indicated on the
mounting template.
• Insert two #6 sheet metal screws (not included),
leaving screw heads protruding 1/8 inch from the
surface.
• Place the timer over the screw heads and push down
to lock into place.
WARNING
Risk of Electric Shock
Keep children away. Unplug timer before cleaning. Fully insert
plug. Do not use near standing water.
Risk of Fire
Do not use to control appliances that contain heating elements
(cooking appliances, heaters, irons, etc.). Do not exceed
electrical ratings.
Outlet
ON
Timer
O
N
AVERTISSEMENT
Risque de choc électrique
Gardez les enfants à l’écart. Débranchez la minuterie avant de
procéder au nettoyage. Insérez complètement la fiche.
N’utilisez pas cet appareil près d’eau stagnante.
Risque d’incendie
N’utilisez pas cet article pour commander des appareils qui
contiennent des éléments chauffants (appareils de cuisson,
radiateurs, fers, etc.). Ne dépassez pas les capacités électriques.
1a
1b
4
5
6
2. Plug timer into an
ELECTRICAL OUTLET
Use an outdoor-rated three-
pronged grounded electrical
outlet. Do not use extension cords
to connect the timer to the power
source.
3. Set a period of time for the
timer to be “ON”
Locate the gray pins and push
them DOWN at the marked times
when the attached device is to be
“ON”. Each pin represents a 30
minute time interval.
2
3
AB1328
PROBLEM POSSIBLE
CAUSE
CORRECTIVE
ACTION
I
AD
Call customer service at 1-866-994-4148,
8 a.m. - 6 p.m., EST, Monday - Thursday,
8 a.m. - 5 p.m., EST, Friday.